ATSAME54P20A-AU - 120MHz Cortex-M4F 1MB MCU | Microchip Technology
料号: ATSAME54P20A-AU ✓ 量产中ATSAME54P20A-AU 概述
A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripheral interfaces, and control logic into one device. The ATSAME54 belongs to the SAM E54 high-performance microcontroller family. Its Cortex-M4F core adds hardware floating-point acceleration, helping improve computational performance in control, signal-processing, and communications workloads while retaining the low-complexity architecture suited to embedded systems.
Key capabilities include up to 120 MHz operation, up to 1 MB of dual-panel Flash with ECC, and up to 256 KB of SRAM with ECC. The family also provides a 10/100 Ethernet MAC and two CAN-FD controllers, making it appropriate for industrial networking, motor control, gateway equipment, and connected automation systems. ECC-protected memory supports data-integrity requirements in applications where uncontrolled bit errors are unacceptable.
The ATSAME54P20A-AU is identified in the manufacturer material as a 1 MB Flash device in a 128-TQFP package. The -AU ordering code corresponds to the tray packaging shown in the product listings. Applications using the device should account for its 120-pin TQFP footprint, 14 mm by 14 mm body size, 3.3 V supply requirement, and the pin assignments defined for the specific ATSAME54P20A device.
The target MPN is suitable for industrial automation, factory equipment, building controls, motor-control platforms, Ethernet-connected controllers, and CAN-FD network nodes. Its combination of high-frequency Cortex-M4F processing, ECC memory, Ethernet MAC, and dual CAN-FD support allows multiple communications functions to be consolidated in a single controller rather than requiring separate interface devices.
PCB implementation requires careful decoupling near the supply pins, correct grounding, and controlled routing for high-speed and communication signals. Firmware development requires the appropriate SAM E54 device support, startup files, linker configuration, clock setup, and peripheral initialization. The manufacturer application information and the ATSAME54 128-pin motor-control reference material should guide pin multiplexing, peripheral routing, and board-level validation.
This product record combines the manufacturer specifications, exact MPN packaging details, available drop-in alternatives, pricing references, comparison parameters, and implementation guidance. It highlights the engineering considerations needed to decide whether the ATSAME54P20A-AU is suitable for an industrial control design and how to evaluate its closest same-package replacements.
直接替换替代料: ATSAME54P20A-AU ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ATSAME54P20A-AU (相同外形与封装尺寸) ——差异在于 Operating Temperature, Package, SRAM, Core Architecture, Flash Memory.
ATSAME54P20A-AU-EFP
✅ 直接替换联系询价
查看数据手册 →ATSAME54P20A-AFT
✅ 直接替换联系询价
查看数据手册 →ATSAME54P20A-AU 最大额定值与电气特性
| Product Type | 32-bit ARM Cortex-M4F microcontroller |
| Processor Core | ARM Cortex-M4F with floating-point unit |
| Maximum CPU Frequency | 120 MHz |
| Flash Memory | 1 MB |
| Flash Organization | 1M x 8 bits |
| Flash Architecture | Dual-panel Flash with ECC |
| Maximum SRAM | 256 KB with ECC |
| 电源电压 | 3.3 V |
| Ethernet Support | 10/100 Ethernet MAC |
| CAN-FD Controllers | 2 |
| 封装 | 128-pin TQFP |
| Package Dimensions | 14 mm x 14 mm |
| 安装类型 | Surface mount |
| 工作温度 | -40C to +85C |
| Core Architecture | ARMv7-M with hardware floating point |
| Memory ECC | Supported for Flash and SRAM |
ATSAME54P20A-AU 14 mm x 14 mm 引脚配置指南
ATSAME54P20A-AU(14 mm x 14 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: ATSAME54P20A-AU.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ATSAME54P20A-AU 适用于 6 应用s: Industrial Motor Control, CAN-FD Networked Controller, Ethernet Industrial Gateway, Factory Automation Controller, Building Automation Equipment, Connected Sensor Hub.
Industrial Motor Control
The ATSAME54P20A-AU fits industrial motor-control platforms that require deterministic 120 MHz Cortex-M4F processing, up to 256 KB of ECC-protected SRAM, and a large 128-pin TQFP pin count for timers, PWM outputs, control loops, and external interfaces. Its hardware floating-point unit is useful for control calculations that would otherwise increase CPU utilization. The two CAN-FD controllers can support networked motion systems, while the 10/100 Ethernet MAC supports supervisory communications. Microchip’s ATSAME54 motor-control plug-in module information identifies the family as suitable for 128-pin motor-control development, although the final design must verify the required timer channels, analog inputs, and external power stage.
推荐
CAN-FD Networked Controller
The ATSAME54P20A-AU is well suited to industrial CAN-FD nodes because it combines two CAN-FD controllers with a 120 MHz Cortex-M4F core and up to 256 KB of ECC-protected SRAM. Engineers can run protocol handling, diagnostics, and local control concurrently while using the Ethernet MAC for supervisory links. The 1 MB dual-panel Flash provides substantial room for application code, boot software, and configuration data, with ECC helping protect firmware integrity. The 128-TQFP package also offers enough pins for isolated CAN-FD transceivers, supervision signals, and digital I/O. Firmware qualification should include bus timing, fault recovery, termination strategy, and validation under the worst expected network traffic.
推荐
Ethernet Industrial Gateway
The ATSAME54P20A-AU can serve as the control processor in a compact Ethernet industrial gateway where 120 MHz performance, ECC-protected memory, and real-time peripheral handling are required. Its integrated 10/100 Ethernet MAC supports network traffic processing, while the two CAN-FD channels allow the gateway to bridge or monitor lower-level industrial networks. The 1 MB of Flash accommodates protocol stacks, configuration data, and secure update mechanisms, and up to 256 KB of SRAM supports packet buffering and concurrent control tasks. Unlike a small 32-pin microcontroller, the 128-TQFP footprint provides extensive I/O for status indicators, configuration interfaces, and isolated communications hardware. Board design should route Ethernet differential pairs according to the manufacturer layout guidance.
推荐
Factory Automation Controller
The ATSAME54P20A-AU supports factory-automation controllers that must combine real-time machine control with communications and diagnostic intelligence. A 120 MHz Cortex-M4F core can execute motion, sequencing, and sensor-processing tasks, while hardware floating-point acceleration benefits filter and compensation algorithms. ECC-protected Flash and SRAM improve integrity in equipment where silent corruption could create unsafe operating conditions. The 10/100 Ethernet MAC provides a management path, and two CAN-FD controllers can connect sensors, drives, or remote I/O modules over high-speed industrial networks. With 128 pins, the controller can expose substantial digital I/O and analog-control channels without an external parallel interface device. Production firmware should add peripheral fault checks and verify startup behavior across all supply and temperature conditions.
推荐
Building Automation Equipment
The ATSAME54P20A-AU is appropriate for building-automation equipment that monitors sensors, controls actuators, and maintains network connectivity. Its 120 MHz Cortex-M4F processor provides ample performance for scheduling, communications, and local diagnostics, while the two CAN-FD channels can support building-network devices. The Ethernet MAC enables integration with supervisory infrastructure, and the large Flash capacity can hold multiple protocol stacks and update images. ECC-protected memory is particularly useful in long-life equipment where transient faults must be detected rather than silently altering control state. The 128-TQFP package supports isolated communication interfaces, digital outputs, and sensing connections. The design should use robust external protection because building controllers may face long wiring runs, transients, and temperature variation beyond the MCU itself.
推荐
Connected Sensor Hub
The ATSAME54P20A-AU can act as a connected sensor hub for industrial IoT equipment requiring local filtering, control, and two forms of network communication. The 120 MHz Cortex-M4F core can process several sensor streams, perform scaling and filtering, and use hardware floating-point operations where algorithm workloads justify them. Up to 256 KB of ECC-protected SRAM provides room for acquisition buffers, while 1 MB of ECC-protected dual-panel Flash supports networking stacks and configuration data. Ethernet carries higher-level traffic, and CAN-FD supports local sensors or actuators. The 128-pin package provides extensive connections for analog and digital sensor interfaces. Engineering validation should include clock accuracy, sensor timing, watchdog behavior, and recovery after network or power disturbances.
推荐
推荐产品汇总
工程参考数据: ATSAME54P20A-AU ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ATSAME54P20A-AU-EFP | ATSAME54P20A-AFT |
|---|---|---|---|
| Package | 128-TQFP (14x14 mm) | 128-TQFP (14x14 mm) | 128-pin PQFP/TQFP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Processor Core | 32-bit ARM Cortex-M4F | 32-bit ARM Cortex-M4F | 32-bit ARM Cortex-M4F |
| Maximum CPU Frequency | 120 MHz | 120 MHz | 100 MHz |
| Flash Memory | 1 MB | 1 MB | 1 MB |
关键差异点
- Higher documented operating frequency (对比 ATSAME54P20A-AFT)
- Extended Flash performance option (对比 ATSAME54P20A-AU)
- Integrated industrial communications (对比 ATSAME54P20A-AFT)
设计说明
Place the device’s required bypass capacitors directly beside their associated supply and ground pins, using the values and placement specified in the manufacturer package documentation. Separate analog and digital supply paths where the application permits, and avoid routing high-current outputs through sensitive input return paths. Validate the power budget across 120 MHz operation and the highest expected peripheral load because processor frequency, Ethernet activity, and CAN-FD transceivers can change current demand over time.
Follow the manufacturer’s 128-TQFP land pattern and pin-numbering diagram exactly, and confirm the package body dimensions are 14 mm by 14 mm. Keep clock, debug, and communication routes away from noisy power-stage routes. Ethernet differential pairs should be routed as a controlled impedance pair with continuous reference planes and minimal stubs. Because the MCU has 128 pins, a careful floorplan is essential to separate communications, motor-control outputs, analog inputs, and ground returns.
Do not treat ATSAME54P20A, ATSAME54P20A-AU, ATSAME54P20A-AFT, and ATSAME54P20A-AU-EFP as interchangeable solely because they share a family name. Review the ordering-information table for temperature grade, package, Flash-performance suffix, and qualification requirements. A hardware footprint match also does not guarantee firmware compatibility; regenerate the startup configuration, linker script, pin definitions, and peripheral initialization for the selected ordering code.
The 120 MHz Cortex-M4F core and active Ethernet or CAN-FD peripherals can raise device temperature beyond the simple idle condition. Use the manufacturer’s maximum-frequency and active-current guidance when estimating junction temperature, and provide copper area around the TQFP without violating isolation or signal-clearance requirements. Validate with chamber-temperature operation, maximum peripheral activity, and worst-case supply voltage rather than relying only on an ambient-temperature calculation.
合规信息
The available manufacturer and distributor records do not explicitly state the requested compliance classifications. The -85C operating-temperature notation appears in a same-package family listing and should be verified against the Microchip ordering table for the exact suffix.