ATTINY44-20MU - 20MHz 8-Bit AVR MCU | Microchip
料号: ATTINY44-20MU ✓ 量产中ATTINY44-20MU 概述
An 8-bit AVR microcontroller is a RISC-based semiconductor that executes compact machine instructions from nonvolatile flash memory. The ATTINY44 belongs to the ATtiny family within the broader hierarchy of embedded microcontroller, processor, and integrated-circuit devices. Its combination of 4 KB program memory, 256 bytes of SRAM, and 12 I/O lines suits compact control, sensing, communication, and low-power peripheral designs.
Key features include 20 MHz maximum operating frequency, 4 KB of in-system-programmable flash, 256 bytes of EEPROM, and 256 bytes of SRAM. The mixed-signal peripherals include a 10-bit ADC and USI, while two timer/counter blocks provide PWM outputs and timing functions. The 20-QFN-EP package also allows a compact PCB footprint and exposes a thermal pad for improved board-level heat spreading.
The device uses an advanced RISC architecture with 32 general-purpose working registers and a Harvard-style separation of program and data memories. In-system programming supports configuration without a separate programming socket. Its small memory organization is useful for dedicated control tasks where a full operating system would add unnecessary complexity. Firmware must respect the limited 4 KB flash and 256-byte SRAM budgets.
Typical uses include compact sensor nodes, industrial control modules, LED lighting controllers, small motor-control boards, and UART-connected instruments. The ADC supports analog measurements, the USI can serve serial or bus-oriented communication tasks, and the PWM channels simplify dimming, proportional control, or waveform generation without external timers.
PCB design should preserve access to the exposed pad, provide clean power and ground connections, and place decoupling capacitance close to the supply pins. Firmware designers should budget SRAM carefully and use the chip’s timer resources rather than polling delays when precision timing is required. The manufacturer datasheet should be used for the exact pad assignment and programming connections.
This product data combines the exact ATTINY44-20MU memory and package specifications with application guidance, package-level comparisons, programming references, and verified drop-in alternatives. It is intended to accelerate engineering selection while clearly separating electrical facts from design recommendations.
直接替换替代料: ATTINY44-20MU ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ATTINY44-20MU (相同外形与封装尺寸) ——差异在于 PWM Channels, Flash Memory, SRAM, Package, EEPROM Memory.
ATTINY44A-MU
✅ 直接替换联系询价
查看数据手册 →ATTINY44A-MMH
✅ 直接替换联系询价
查看数据手册 →ATTINY84-20MU
✅ 直接替换联系询价
查看数据手册 →ATTINY44-20MU 最大额定值与电气特性
| Product Type | 8-bit AVR RISC microcontroller |
| 最大时钟频率 | 20 MHz |
| Flash Memory | 4 KB (2K x 16 bytes) |
| EEPROM Memory | 256 bytes |
| SRAM | 256 bytes |
| General-Purpose I/O Lines | 12 lines |
| General-Purpose Working Registers | 32 registers |
| Architecture | Advanced RISC |
| ADC | 10-bit ADC |
| USI | Universal Serial Interface |
| Timer/Counter Blocks | 2 timer/counter blocks |
| PWM Channels | 4 PWM channels |
| Operating Voltage | 2.7 V to 5.5 V |
| 封装 | 20-QFN-EP, 4 x 4 mm |
| 安装类型 | Surface mount |
| Programming | In-system programmable |
ATTINY44-20MU 20-qfn-ep, 4 x 4 mm 引脚配置指南
ATTINY44-20MU(20-qfn-ep, 4 x 4 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: ATTINY44-20MU.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ATTINY44-20MU 适用于 6 应用s: Compact Sensor Node, UART Connected Control Module, LED Lighting Controller, Small Motor Control, Industrial Interface Module, Programmable Logic Controller.
Compact Sensor Node
The ATTINY44-20MU fits a compact sensor node because its 10-bit ADC can sample analog inputs while the 20 MHz AVR core performs local filtering and control. The device provides 256 bytes of SRAM and 4 KB of flash, so firmware must use small buffers and avoid memory-heavy libraries. It is particularly appropriate for a battery-powered environmental monitor that periodically wakes, converts sensor readings, updates an indicator, and returns to a low-power state. Its 20-QFN-EP package also preserves PCB area in a densely populated sensor assembly.
推荐
UART Connected Control Module
The ATTINY44-20MU is suitable for a UART-connected control module when the device needs local logic, timers, and analog support without a larger processor. Its 20 MHz clock provides adequate response time for command parsing, debouncing, and actuator updates, while the 12 I/O lines leave several pins available for status LEDs or digital inputs. The 256-byte SRAM is sufficient for short message buffers but not large frame accumulation. Firmware should use the exact UART pin assignment and clock configuration from the manufacturer datasheet before finalizing the board.
推荐
LED Lighting Controller
The ATTINY44-20MU can control LED lighting because its timer/counter blocks provide four PWM channels and 12 general-purpose I/O lines. It can implement dimming, fades, status patterns, and simple power sequencing without an external timing controller. The 4 KB flash is adequate for a focused lighting routine, and the 20 MHz core allows PWM updates and button handling to share the device. Use transistor or MOSFET drive stages where the LED string current exceeds the MCU output limits, and check the exposed-pad connection for effective heat spreading.
推荐
Small Motor Control
The ATTINY44-20MU is practical for a small closed-loop or duty-cycle motor controller because its four PWM channels can command power stages, its timers can establish periods, and its ADC can monitor a feedback signal. The 20 MHz processing rate supports responsive control calculations, while 256 bytes of SRAM is suitable for modest state variables rather than large motion-control algorithms. The device should not drive a motor directly; use a suitable gate driver and power MOSFET stage. Validate startup behavior, current limits, and thermal conditions at the worst mechanical load.
推荐
Industrial Interface Module
The ATTINY44-20MU works well in a small industrial interface module that converts discrete inputs and analog measurements into protocol data. Its 12 I/O lines support switches, alarm outputs, and status signaling, while the ADC adds measurement capability without requiring a separate converter. The ATtiny architecture executes a single event loop efficiently, although the 4 KB flash and 256-byte SRAM require disciplined firmware organization. Industrial equipment should also include appropriate input protection, isolation, surge handling, and grounding beyond the MCU itself.
推荐
Programmable Logic Controller
The ATTINY44-20MU can act as a compact programmable logic controller for deterministic tasks such as relay sequencing, pulse counting, time-based interlocks, and simple alarm logic. Two timer/counter blocks and four PWM outputs provide useful timing resources, while 12 I/O lines permit a mixture of inputs and outputs. Its 20 MHz clock and in-system programming support fast development and field updates. Because memory is limited, organize execution as a scheduled state machine, retain critical configuration in EEPROM, and include watchdog recovery in production firmware.
推荐
推荐产品汇总
工程参考数据: ATTINY44-20MU ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ATTINY44A-MU | ATTINY44A-MMH | ATTINY84-20MU |
|---|---|---|---|---|
| Package | 20-QFN-EP (4x4) | 20-QFN-EP (4x4) | 20-QFN-EP (4x4) | 20-QFN-EP (4x4) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Architecture | 8-bit AVR RISC | 8-bit AVR RISC | 8-bit AVR RISC | 8-bit AVR RISC |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Flash Memory | 4 KB | 4 KB | 4 KB | 8 KB |
| SRAM | 256 bytes | 256 bytes | 256 bytes | 512 bytes |
| EEPROM | 256 bytes | 256 bytes | 256 bytes | 512 bytes |
| ADC | 10-bit ADC | 10-bit ADC | 10-bit ADC | Larger ADC |
| USI | Universal Serial Interface | Universal Serial Interface | Universal Serial Interface | Universal Serial Interface |
| PWM Channels | 4 channels | 4 channels | 4 channels | 4 channels |
关键差异点
- Direct same-generation footprint match (对比 ATTINY44A-MU)
- Memory expansion without changing the package (对比 ATTINY84-20MU)
- Orderable same-family alternative (对比 ATTINY44A-MMH)
设计说明
Place the decoupling capacitor immediately between the supply and ground pins, and connect the exposed thermal pad to the appropriate ground plane according to the package drawing. The 20-QFN-EP body provides only 4 x 4 mm of board area, so solder mask spacing, via placement, and thermal-pad fill must follow the manufacturer land-pattern recommendations. Keep high-current switching nodes and inductive traces away from the ADC and oscillator nets.
The device supports a 2.7 V to 5.5 V operating range, but the selected supply voltage affects clock limits, output levels, and peripheral behavior. Use a regulator with adequate transient response and noise performance for the board rather than adding capacitance solely to compensate for an unstable source. Check absolute maximum and recommended operating conditions in the manufacturer datasheet, especially when designing at the voltage limits or using high-speed clock operation.
The ATTINY44 has only 256 bytes of SRAM, so stack-heavy interrupt routines, recursive calls, and large local buffers can cause instability without an obvious compiler warning. Keep interrupts short, use static buffers carefully, and reserve stack space for the deepest interrupt nesting case. Also avoid treating the 4 KB flash as an application buffer; move constants into EEPROM only when nonvolatile storage and write endurance are appropriate.
Keep the crystal or clock source, programming interface, and reset circuitry close to their associated device pins. Route ADC inputs away from PWM outputs, switching nodes, and high-current return paths to reduce conversion errors. For UART-connected boards, provide a stable common ground and use a level shifter when the external host voltage differs from the ATTINY44 supply. Review unused pins and their configured states in the final firmware.
合规信息
The ATTINY44-20MU is an industrial and commercial microcontroller rather than an AEC-Q100 automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not confirmed in the retrieved sources.