BSC9132NSE7KNKB - QorIQ Qonverge SoC, 2x e500+2x SC3850 | NXP
料号： BSC9132NSE7KNKB ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $425 | $425.00 |
| 10 | $395 | $3,950.00 |
| 100 | $360 | $36,000.00 |
| 500 | $335 | $167,500.00 |
| 1,000 | $305 | $305,000.00 |
BSC9132NSE7KNKB 概述
A multicore SoC (System-on-Chip) is a highly integrated processor that merges general-purpose CPU cores, DSP cores, hardware accelerators, memory controllers, and I/O peripherals onto one silicon die. The BSC9132 belongs to NXP's QorIQ Qonverge platform, which sits at the intersection of MPU (microprocessor) and DSP (digital signal processor) products; it functions as a baseband processor that performs physical-layer modulation, demodulation, and Layer-2 protocol processing without requiring an external companion processor.
Key headline features include two PowerPC e500 cores running up to 1 GHz, two StarCore SC3850 DSP cores running up to 1 GHz, an integrated MAPLE-B2P hardware accelerator for baseband forward-error-correction offload, a 32-bit DDR3 memory controller with ECC, integrated SEC security engine for cryptographic acceleration, and a SerDes-based multi-protocol fabric. The device is offered in a 780-ball FCBGA with commercial 0C to +105C temperature range.
Architecturally the BSC9132 uses a coherent CoreNet fabric that ties CPU, DSP, and accelerator blocks together, allowing shared-memory programming across heterogeneous cores. The MAPLE-B2P block offloads turbo-decoding and Viterbi decoding, freeing DSP cycles for Layer-1 synchronization and channel estimation. The DDR3 controller supports up to DDR3-1066 with ECC for reliability in carrier-grade deployments.
Typical applications include small-cell LTE femtocell base stations, LTE/WiMAX PHY Layer-1 cards, smart-grid communication controllers, industrial deterministic networking platforms, and secure defense radio systems. The combination of CPU + DSP + hardware accelerator makes it well suited to any system that must execute both control-plane and signal-processing workloads concurrently.
Design consideration: this BGA-780 part requires a multilayer PCB with via-in-pad and controlled-impedance SerDes routing; thermal management is critical because the device dissipates significant power at full CPU plus DSP loading. Software development requires NXP's CodeWarrior or Linux SDK with SMP Linux 3.x and StarCore DSP toolchain.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone, including parametric match percentages and cross-sourcing from NXP's Qonverge family portfolio.
直接替换替代料： BSC9132NSE7KNKB ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： BSC9132NSE7KNKB （相同外形与封装尺寸） ——差异在于 Operating Temperature, RoHS Status, Security Engine.
快速对比工具——选择替代料号进行并排对比：
BSC9132NXE7KNKB
✅ 直接替换✓ 有现货
$198 / 个
查看数据手册 →BSC9131NSE7KNKB
✅ 直接替换📋 参考替代料（不在目录中）
BSC9132NSE7MNK
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
BSC9132NSE7KNKB 最大额定值与电气特性
| Manufacturer | NXP Semiconductors |
| Series | QorIQ Qonverge BSC9132 |
| Product Type | Multicore SoC (CPU + DSP + Accelerator) |
| CPU Cores | 2x PowerPC e500 |
| CPU Core Frequency | 1 GHz (up to) |
| DSP Cores | 2x StarCore SC3850 |
| DSP Core Frequency | 1 GHz (up to) |
| Hardware Accelerator | MAPLE-B2P (turbo / Viterbi decode) |
| 数据总线宽度 | 32-bit |
| Memory Controller | DDR3 with ECC |
| Security Engine | SEC (cryptographic accelerator) |
| 封装 | 780-FCBGA (23x23 mm) |
| 工作温度 | 0C to +105C |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
BSC9132NSE7KNKB 780-fcbga (23x23 mm) 引脚配置指南
BSC9132NSE7KNKB（780-fcbga (23x23 mm) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： BSC9132NSE7KNKB.
请参阅 数据手册 以查看完整引脚配置。
典型应用
BSC9132NSE7KNKB 适用于 6 应用s: Small-Cell LTE Base Station, LTE/WiMAX Physical Layer Card, Smart-Grid Communication Controller, Defense / Military Radio Platform, Industrial Deterministic Networking Platform, Enterprise VoIP / Unified-Communications Appliance.
Small-Cell LTE Base Station
The BSC9132NSE7KNKB fits small-cell LTE base station baseband cards because it combines dual PowerPC e500 control-plane cores with dual StarCore SC3850 signal-processing cores and the MAPLE-B2P accelerator on a single die. The 1 GHz CPU clock, MAPLE-B2P turbo/Viterbi offload, and DDR3-ECC memory controller meet real-time LTE PHY budgets for femtocell and picocell deployments. Placed on a small-cell baseband card, the SoC executes Layer-1 modulation, Layer-2 protocol stacks, and IQ data routing without a companion processor. The integrated SEC engine secures backhaul traffic via hardware-accelerated cipher suites, reducing software overhead. Designers benefit from consolidated BOM and reduced board area compared with discrete CPU + DSP architectures.
推荐
LTE/WiMAX Physical Layer Card
The BSC9132NSE7KNKB is purpose-built for LTE/WiMAX PHY Layer-1 cards because its SC3850 DSP cores at 1 GHz, MAPLE-B2P accelerator, and coherent CoreNet fabric execute PHY synchronization, channel estimation, and FEC decoding under hard real-time deadlines. The DDR3 controller with ECC handles the large IQ-sample buffers required for OFDMA modulation, while the SEC engine accelerates Kasumi / Snow 3G cipher for user-plane integrity. Placed between RF front-end and upper-layer processing, the SoC consolidates baseband, control, and security into one chip. The 780-FCBGA package supports controlled-impedance SerDes break-out for CPRI/OBSAI backhaul interfaces, simplifying RF-to-bus connectivity.
推荐
Smart-Grid Communication Controller
The BSC9132NSE7KNKB fits smart-grid communication controllers because its dual PowerPC e500 cores handle industrial protocol stacks (IEC 61850, DNP3, Modbus) while the StarCore SC3850 DSP cores process simultaneous power-line communication or wireless metering data streams. The 0C to +105C temperature range and DDR3 with ECC support reliable operation in substation environments with extended thermal stress. The SEC engine provides secure firmware attestation and cryptographic isolation for critical-infrastructure compliance, while MAPLE-B2P accelerates FEC on noisy power-line channels. Designers benefit from a single-chip solution that replaces separate CPU + DSP daughter-card stacks, reducing mean time between failure in long-life grid deployments.
推荐
Defense / Military Radio Platform
The BSC9132NSE7KNKB suits defense radio platforms because its CPU + DSP + hardware accelerator topology supports software-defined radio (SDR) waveforms including HAVE QUICK, SINCGARS, and modern wideband tactical radios. The MAPLE-B2P accelerator handles low-latency FEC required by tactical waveforms, while the SEC engine provides tamper-resistant crypto for classified traffic. The coherent CoreNet fabric allows shared-memory programming across CPU and DSP cores, simplifying SDR waveform porting. Designers validate against MIL-STD-810 environmental conditions and MIL-STD-461 EMI limits with the 780-FCBGA mounted on ruggedized multilayer PCBs. The same BSP / toolchain used in commercial LTE deployments shortens qualification cycles.
推荐
Industrial Deterministic Networking Platform
The BSC9132NSE7KNKB serves industrial deterministic networking platforms because its PowerPC e500 cores run real-time OS (RTOS) schedulers at 1 GHz while the SC3850 DSP cores process deterministic audio/video or vibration signal streams. The DDR3 controller with ECC and the SEC engine deliver the reliability required for industrial Ethernet gateways, PROFINET controllers, and TSN bridges. The 780-FCBGA 23x23 mm footprint allows compact industrial footprint designs with adequate thermal headroom. Designers pair the SoC with NXP's industrial PHY and switch portfolio (SJA1105, TJA1101) to build full industrial Ethernet solutions. The same OS image works across the Qonverge family, simplifying field upgrades.
推荐
Enterprise VoIP / Unified-Communications Appliance
The BSC9132NSE7KNKB suits enterprise VoIP / unified-communications appliances because the dual e500 cores execute packet processing, SIP/H.323 stacks, and QoS scheduling, while the StarCore SC3850 DSP cores handle narrowband / wideband audio codecs (G.722, Opus, SILK) at low latency. The MAPLE-B2P offloads acoustic-echo-cancellation FEC for handset-grade voice quality, and DDR3-ECC provides deterministic latency for conference bridge buffers. Placed on a 1U appliance mainboard, the SoC handles up to hundreds of concurrent VoIP sessions without external DSP chips. Designers benefit from consolidating control-plane, media-plane, and security onto one BGA component, simplifying thermal and EMC design.
推荐
推荐产品汇总
工程参考数据： BSC9132NSE7KNKB ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | BSC9132NXE7KNKB | BSC9131NSE7KNKB | BSC9132NSE7MNK |
|---|---|---|---|---|
| Package | 780-FCBGA (23x23 mm) | 780-FCBGA (23x23 mm) - same | 780-FCBGA (23x23 mm) - same | 780-FCBGA (23x23 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| CPU Cores | 2x e500 @ 1 GHz | 2x e500 @ 1 GHz | 2x e500 @ 1 GHz | 2x e500 @ 1 GHz |
| DSP Cores | 2x SC3850 @ 1 GHz | 2x SC3850 @ 1 GHz | 1x SC3850 @ 1 GHz (-50%) | 2x SC3850 @ 1 GHz |
| Hardware Accelerator | MAPLE-B2P | MAPLE-B2P | MAPLE-B (older generation, lower throughput) | MAPLE-B2P |
| Memory Controller | DDR3 with ECC, 32-bit | DDR3 with ECC, 32-bit | DDR3 with ECC, 32-bit | DDR3 with ECC, 32-bit |
| Operating Temperature | 0C to +105C | 0C to +105C | 0C to +105C | 0C to +105C |
| Lifecycle Status | Active | Active | Active | Active |
关键差异点
- Higher DSP cluster count for parallel baseband workloads （对比 BSC9131NSE7KNKB)
- MAPLE-B2P accelerator generation （对比 BSC9131NSE7KNKB)
- Same family, same package, same toolchain （对比 BSC9132NSE7MNK)
设计说明
The BSC9132NSE7KNKB dissipates significant power at full dual e500 + dual SC3850 + MAPLE-B2P loading; in a typical 4G/4.5G small-cell deployment the device draws 8-12 W. The 780-FCBGA 23x23 mm package requires a multilayer PCB with at least 8 thermal vias under the die shadow, plus a heat spreader or heatsink for sustained load. Junction temperature must remain below 105C; monitoring via on-die thermal diodes is recommended.
Route the SerDes lanes (CPRI/OBSAI/PCIe) with 85-ohm differential impedance and length-matching tolerance within 0.15 mm between pair members. Use the NXP reference design footprint for the 780-FCBGA including via-in-pad and microvia stack-up to escape the inner-row BGA signals. Decoupling requires 0.1 uF X7R close to every power pin plus bulk polymer / tantalum capacitors at each voltage rail entry point.
Do not power the device outside the manufacturer datasheet power-sequencing requirements; the BSC9132 enforces a strict VDD / VDD_CORE / VDD_DDR ramp order and monitors via the internal SEC engine. Reboot can be triggered if rail sequencing violates spec, leaving the device in a non-recoverable state without external reset. Designers must implement proper POR sequencing as described in section 4 of the manufacturer datasheet.
DDR3 interfaces on the BSC9132NSE7KNKB require matched-length routing and careful trace impedance control; the ECC byte lane must be routed to a populated DRAM device and validated through IBIS simulation. SSTL-15 signaling is used; reference the NXP reference board design files for byte-lane pairing and capacitor placement. Mismatched write/read timing budgets will surface as intermittent data-corruption under load.
合规信息
RoHS and lead-free compliant per NXP product page. Not AEC-Q100 qualified (commercial 0C to +105C). REACH and conflict-mineral compliance indicated; halogen-free status not explicitly stated in available data.
