CY8C3446LTI-084 - 8-Bit 50MHz PSoC 3 MCU | Infineon
料号: CY8C3446LTI-084 ✓ 量产中CY8C3446LTI-084 概述
A programmable system-on-chip is a mixed-signal semiconductor that integrates a microcontroller, analog converters, comparators, timers, and programmable digital logic into one package. The PSoC 3 family places these resources behind configurable peripherals, so a designer can adapt signal acquisition, conditioning, and control behavior to an application instead of fixing every function in dedicated silicon. This places the CY8C3446LTI-084 within the hierarchy of embedded controllers, mixed-signal microcontrollers, and programmable system-on-chip devices.
Three headline characteristics define the device: its 50 MHz maximum CPU clock, 64 KB flash program memory, and 8 KB SRAM. The 8051-based processor provides a familiar instruction set while the PSoC architecture adds configurable analog and digital peripherals. The 1.71 V to 5.5 V operating range supports both 3.3 V and 5 V system rails, and the listed 25 I/O provide connections for sensors, actuators, communications, and control signals within a compact 8 mm by 8 mm footprint.
The 64 KB flash provides on-chip program storage for firmware, while the 8 KB SRAM holds working data, stack state, and peripheral buffers. The 50 MHz clock supports faster control loops and time-sensitive digital functions than lower-clock 8-bit systems. The exact divider, timer, ADC, DAC, comparator, and GPIO configuration available to a specific design should be confirmed against the device datasheet because PSoC peripheral assignments are selected through device configuration rather than through a fixed external pin map.
Typical uses include industrial sensor controllers, building and access-control modules, compact motor-control boards, digital potentiometer and analog-interface designs, and low-cost consumer products with a small number of mixed-signal I/O functions. Its small QFN package also suits densely populated control boards where component area is limited. Designers should confirm that the exposed-pad connection and thermal requirements are compatible with the PCB stack-up and assembly process.
When planning a PCB layout, place decoupling capacitors close to the supply pins, route sensitive analog inputs away from fast-switching nodes, and follow the manufacturer's recommended exposed-pad land pattern. Because a mixed-signal device can combine sensitive analog functions with digital peripherals, grounding, isolation between analog and digital return paths, and stable reference routing can be as important as the pin assignment itself.
This page consolidates the key device characteristics, ordered-family alternatives, package details, application guidance, and practical PCB considerations into one engineering reference. It is designed to support initial component selection and board planning while directing final verification to the manufacturer datasheet for the exact ordering code, temperature grade, pin multiplexing, and electrical limits.
直接替换替代料: CY8C3446LTI-084 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: CY8C3446LTI-084 (相同外形与封装尺寸) ——差异在于 CPU Core, Package, Program Memory.
CY8C3446LTI-074
✅ 直接替换联系询价
查看数据手册 →CY8C3446LTI-073
✅ 直接替换联系询价
查看数据手册 →CY8C3446LTI-085
✅ 直接替换联系询价
查看数据手册 →CY8C3446LTI-084 最大额定值与电气特性
| Product Type | 8-bit PSoC 3 mixed-signal microcontroller |
| CPU Core | 8051, 8-bit |
| Maximum CPU Frequency | 50 MHz |
| Program Memory | 64 KB flash (64K x 8) |
| SRAM | 8 KB |
| 工作电源电压 | 1.71 V to 5.5 V |
| I/O Count | 25 I/O |
| Programmable Analog and Digital Resources | PSoC 3 configurable mixed-signal architecture |
| 封装 | 68-QFN, 8 mm x 8 mm |
| Package Type | QFN, surface mount |
| 安装类型 | Surface Mount |
| Ordering Code | CY8C3446LTI-084 |
CY8C3446LTI-084 qfn, surface mount 引脚配置指南
CY8C3446LTI-084(qfn, surface mount 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: CY8C3446LTI-084.
请参阅 数据手册 以查看完整引脚配置。
典型应用
CY8C3446LTI-084 适用于 6 应用s: Industrial Sensor Controller, Building Access and Security Control, Compact Motor and Actuator Control, Digital Potentiometer and Analog Interface, Networked Data Acquisition Module, Consumer Interface and Control Module.
Industrial Sensor Controller
The CY8C3446LTI-084 fits industrial sensor-controller boards that must acquire, condition, and interpret multiple signals within a limited footprint. Its 50 MHz 8051 CPU provides execution headroom for control algorithms, while 64 KB of flash stores application firmware and 8 KB of SRAM supports working buffers and peripheral state. The PSoC 3 configurable analog and digital resources can implement interface functions without multiplying discrete components. Place bypass capacitors near the supply pins and keep analog traces away from switching nodes so the small 8 mm by 8 mm 68-QFN package maintains a usable signal environment.
推荐
Building Access and Security Control
The CY8C3446LTI-084 is appropriate for access-control and security modules that combine local decision logic with external sensors and electromechanical outputs. The 25 I/O can support digital inputs, indicator outputs, and bus connections, while the 50 MHz processor handles debouncing, state-machine updates, and communication tasks. The 64 KB flash accommodates protocol and application code, and 8 KB of SRAM is useful for event buffers. In a compact 68-QFN implementation, maintain a clean analog reference path and isolate long external lines from sensitive control inputs to improve system immunity.
推荐
Compact Motor and Actuator Control
The CY8C3446LTI-084 can serve as the logic controller in compact motor, valve, or actuator products where deterministic digital control and mixed-signal support are needed. The 50 MHz 8051 core executes position, speed, or timing routines, while configurable timers and digital blocks handle pulse generation and input capture. With 64 KB of flash for control code and 8 KB of SRAM for state variables, the device provides useful capacity without requiring a larger package. Keep switching-device drives and motor wiring separated from analog and low-level control traces to prevent transient coupling into the microcontroller.
推荐
Digital Potentiometer and Analog Interface
The programmable mixed-signal resources of the CY8C3446LTI-084 make it suitable for digital potentiometer, signal-conditioning, and interface-control products. The 8051 core runs at 50 MHz, providing deterministic control of configurable analog and digital blocks, while 64 KB flash stores lookup tables and device logic. The device consolidates functions that would otherwise require separate microcontroller support and passive networks. Layout quality is especially important in this use: route high-impedance analog inputs away from digital outputs and use the manufacturer's recommended grounding arrangement to minimize conversion error.
推荐
Networked Data Acquisition Module
The CY8C3446LTI-084 fits compact data-acquisition modules that gather local measurements and forward processed results over a digital interface. Its 50 MHz processor can run sampling schedules, filtering, calibration, and protocol handling, while the configurable peripheral architecture supports signal-path customization. The 64 KB flash and 8 KB SRAM provide separate program and working-memory regions for a standalone controller. A communication companion such as an Ethernet transceiver or RS-232 interface can be placed nearby, but the layout should separate high-speed digital return currents from the analog input area.
推荐
Consumer Interface and Control Module
The CY8C3446LTI-084 is suitable for compact consumer products that need flexible control and configurable peripheral behavior in a small board area. The 25 I/O support keys, indicators, displays, and serial links, while the 50 MHz CPU can coordinate multiple UI and control tasks. Its 1.71 V to 5.5 V operating range permits integration across common 3.3 V and 5 V rails. The 68-QFN package reduces board-space demand, but exposed-pad soldering and ground-via placement must follow the manufacturer layout guidance to maintain electrical and thermal performance.
推荐
推荐产品汇总
工程参考数据: CY8C3446LTI-084 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | CY8C3446LTI-074 | CY8C3446LTI-073 | CY8C3446LTI-085 |
|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon |
| Package | 68-QFN (8 mm x 8 mm) | 68-QFN (8 mm x 8 mm) - same | 68-QFN (8 mm x 8 mm) - same | 68-QFN (8 mm x 8 mm) - same |
| Product Family | PSoC 3 CY8C34xx | PSoC 3 CY8C34xx | PSoC 3 CY8C34xx | PSoC 3 CY8C34xx |
| CPU Core | 8051, 8-bit | 8051, 8-bit | 8051, 8-bit | 8051, 8-bit |
| Maximum CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Program Flash | 64 KB | 64 KB | 64 KB | 64 KB |
| SRAM | 8 KB | 8 KB | 8 KB | 8 KB |
| Ordering Configuration | LTI-084 | LTI-074 | LTI-073 | LTI-085 |
关键差异点
- Configurable mixed-signal integration (对比 CY8C3446LTI-074)
- High clock rate with embedded memory (对比 CY8C3446LTI-073)
- Wide 3.3 V and 5 V system compatibility (对比 CY8C3446LTI-085)
设计说明
Use the manufacturer land pattern and exposed-pad drawing before releasing the PCB artwork. Place the required bypass capacitors adjacent to the supply pins, with short and wide return paths to the ground plane. The exposed pad is a central thermal and electrical feature of the 68-QFN package, so its via pattern and solder-assembly profile must be coordinated with the board stack-up and soldering process.
Separate analog inputs and references from digital switching nodes wherever the PSoC configuration permits. PSoC peripherals can place analog and digital functions in the same device, so package adjacency alone does not guarantee signal isolation. Route sensitive inputs on the quiet side of the board, avoid coupling to the clock net and high-current outputs, and use a continuous ground reference beneath the device.
Do not create the PCB pinout from a generic QFN drawing. The CY8C3446LTI-084 uses programmable peripheral multiplexing, and the selected PSoC configuration determines which functions appear on many pins. Verify the pin-description table for the exact ordering code, review startup and configuration pins in the manufacturer's datasheet, and regenerate the firmware configuration whenever the peripheral assignment changes.
Design the supply network for both 3.3 V and 5 V operating environments only after confirming all selected I/O levels and external interfaces. Follow the manufacturer guidance for supply voltage, decoupling, and power sequencing. Keep analog and digital return currents under their respective signal domains and connect them at a controlled low-impedance point to reduce ground-potential differences across sensitive PSoC blocks.
合规信息
Compliance declarations are not stated in the cited catalog records. Request the current manufacturer product declarations for the exact ordering code before release to a regulated market.