Analog Devices

DG408CY+T - 8:1 CMOS Analog Multiplexer | Analog Devices

料号: DG408CY+T ✓ 量产中
-20 V to -5 V or 5 V to 30 V Vdss 100 ohm Rds(on) 16-SOIC, 4.4 mm nominal body width Package
最小起订量: 1 |

DG408CY+T 概述

The Analog Devices DG408CY+T is an improved 8-channel, single-ended CMOS analog multiplexer with a 100 ohm maximum on-resistance, 16-SOIC package, and 8:1 channel configuration. Designed for multiplexing one of eight analog inputs into a common output, it uses TTL/CMOS-compatible address and enable controls and supports single or dual supply operation.

An analog multiplexer is a switching interface that routes multiple analog signals through one shared output path. The DG408 family belongs to the analog switch and multiplexer hierarchy, where reduced channel count, low on-resistance, low charge injection, and controlled leakage become important when precision signals must be selected without introducing excessive error. This device can also operate in a demultiplexing arrangement when signal flow is reversed.

Key characteristics include a maximum on-resistance of 100 ohms, 8 ohm maximum on-resistance flatness, and 9 pC maximum charge injection. Input off leakage is limited to 5 nA at +85 degrees Celsius, while the logic section accepts TTL/CMOS-compatible control levels. ESD protection exceeds 2000 V, and low power consumption is specified at a maximum of 1.25 mW. Rail-to-rail signal handling supports operation across the supplied analog signal range.

The internal design uses eight CMOS analog switches, a digital decoder for channel selection, a voltage reference for logic thresholds, and an enable input for device selection when several multiplexers share a bus. Analog Devices describes the DG408 and DG409 as pin-compatible plug-in upgrades for the industry-standard DG408 and DG409 families, while Renesas identifies them as drop-in replacements for popular DG508A and DG509A devices.

Typical uses include audio-signal routing, communication systems, data-acquisition equipment, guidance and control systems, sample-and-hold circuits, and test equipment. The 16-SOIC package supports conventional surface-mount assembly, and the DG408CY+T commercial-temperature ordering code targets operation from 0 to +70 degrees Celsius.

Designers should account for charge injection during channel transitions and keep sensitive analog traces short and adequately decoupled. Supply rails, logic thresholds, signal amplitude, and the selected input channel must remain within the manufacturer’s operating limits. Because the device can conduct equally well in either direction, it is suitable for both multiplexing and demultiplexing.

This page combines manufacturer specifications, package and temperature details, drop-in replacement information, and application-focused engineering guidance. It also highlights the measurable differences among compatible DG408 variants so that PCB reuse can be evaluated without overlooking temperature grade, package construction, or channel-selection requirements.

直接替换替代料: DG408CY+T ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: DG408CY+T (相同外形与封装尺寸) ——差异在于 Package, Channel Matching, Charge Injection, Configuration, ESD Protection.

Maxim Integrated
Package: 16-SOIC narrow
Channel Matching: 8Ω maximum
Charge Injection: 15pC maximum
对比 DG408CY+T →
Analog Devices
Package: 16-SOIC
Channel Matching: 8 ohm maximum
对比 DG408CY+T →

DG408CY+

✅ 直接替换
Maxim Integrated
📦 16-SOIC
8-channel CMOS analog multiplexer · Single 8:1 multiplexer · 100Ω maximum · 8Ω maximum · 9Ω maximum · 15pC maximum · 5nA maximum at 85°C · 1.25mW maximum

联系询价

查看数据手册 →

DG408DY+T

✅ 直接替换
📦 16-SOIC
Operating range changes from 0 to +70 degrees Celsius to -40 to +85 degrees Celsius

📋 参考替代料(不在目录中)

DG408DY+

✅ 直接替换
Analog Devices
📦 16-SOIC
8:1 · 8 channels · 100 ohm maximum · 8 ohm maximum · 9 ohm maximum · Single 8-channel · Monolithic CMOS · TTL/CMOS-compatible

联系询价

查看数据手册 →

DG408EUE+T

✅ 直接替换
📦 16-SOIC
Cross-reference information reports matching performance profiles, with no measurable primary-parameter difference identified

📋 参考替代料(不在目录中)

DG408DJZ

✅ 直接替换
📦 16-SOIC
Same DG408 8-channel function, with an extended-temperature ordering option instead of the commercial 0 to +70 degrees Celsius grade

📋 参考替代料(不在目录中)

DG408CY+T 规格参数

Configuration 1 circuit, 8:1 single-ended multiplexer
Number of Channels 8 channels
Maximum On-Resistance 100 ohm
On-Resistance Flatness 8 ohm maximum
Charge Injection 9 pC maximum
Input Off Leakage 5 nA maximum at +85 degrees Celsius
Maximum Input Leakage 100 ohm maximum
Power Consumption 1.25 mW maximum
Signal Handling Rail-to-rail
Logic Compatibility TTL/CMOS compatible
ESD Protection >2000 V
Supply Voltage Range -20 V to -5 V or 5 V to 30 V
工作温度 0 degrees Celsius to +70 degrees Celsius
Temperature Grade Commercial
封装 16-SOIC, 4.4 mm nominal body width
安装类型 Surface mount
Package Shape Rectangular
RoHS 状态 Compliant

DG408CY+T rectangular 引脚配置指南

DG408CY+T(rectangular 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

DG408CY+T 的 rectangular 封装引脚图

暂无详细引脚数据: DG408CY+T.

请参阅 数据手册 以查看完整引脚配置。

典型应用

DG408CY+T 适用于 6 应用s: Audio Signal Routing, Data Acquisition Systems, Communication Systems, Sample-and-Hold Circuits, Guidance and Control Systems, Test and Measurement Equipment.

🎧

Audio Signal Routing

DG408CY+T is well suited to selecting among several audio inputs when a system must preserve usable signal amplitude across a shared output path. Its 100-ohm maximum on-resistance limits voltage loss into moderate loads, while rail-to-rail signal handling supports direct routing across the applied analog supply range. Eight channels can replace multiple discrete selectors and reduce routing complexity in audio-signal routing equipment. Designers should still budget for the 9-pC maximum charge injection when channels change during sensitive transitions. Practical layouts should keep the common output short, provide a stable return path, and place any required filtering after the multiplexer so switching transients do not feed back into upstream stages.

📊

Data Acquisition Systems

DG408CY+T can route up to eight external measurements into one data-acquisition channel, reducing the number of front-end inputs required by a controller or converter. The 5-nA maximum input-off leakage at +85 degrees Celsius is especially useful when the measured source has high impedance, because leakage from unselected channels can otherwise create errors. The 8:1 configuration also permits demultiplex operation when returning multiple switched signals through one conductor. For accurate acquisition, allow the circuit to settle after each address change, include anti-alias filtering suited to the measurement bandwidth, and verify the combined effects of source impedance, switch resistance, and charge injection against the required accuracy.

🌐

Communication Systems

DG408CY+T provides analog channel selection for communication equipment that must route transmit, receive, feedback, or test paths through a shared analog stage. TTL/CMOS-compatible address and enable controls simplify coordination with standard digital logic, while the eight-channel arrangement offers more routing flexibility than a single-pole selector. The 100-ohm maximum on-resistance should be evaluated against the input impedance of the following RF or baseband stage; it is generally more appropriate for low-frequency and instrumentation paths than for impedance-sensitive high-frequency designs. Control traces should remain short, and supply bypassing should be located close to the device to prevent logic or supply transients from coupling into the selected channel.

⚡

Sample-and-Hold Circuits

DG408CY+T can select one of eight source signals for a sample-and-hold or pulsed-measurement system, allowing one high-value converter or amplifier to serve multiple inputs. Its low leakage of 5 nA maximum at +85 degrees Celsius helps preserve accuracy when sampling high-impedance sources, and its 8:1 arrangement supports shared acquisition hardware. The dominant engineering consideration is charge injection: the specified 9-pC maximum can create a voltage step whenever the address changes. Use sufficiently long acquisition times, source impedances that limit injected-error gain, and a sampling architecture that isolates the source during the transition. Verify the complete settling behavior with the source impedance and front-end capacitance used in the final design.

🏭

Guidance and Control Systems

DG408CY+T is applicable when a guidance or control system must select among several sensor, feedback, or command signals for common processing. Eight channels reduce the routing burden in compact control assemblies, and the commercial 0-to-+70-degree-Celsius grade is appropriate for indoor laboratory, industrial enclosure, or room-temperature equipment. The device’s ESD protection above 2000 V adds useful robustness, but system designers must still provide appropriate external protection for long cables and field wiring. Use a common ground reference, keep high-impedance sensor paths away from switching controls, and include diagnostics that identify which channel is selected. Confirm that every multiplexed signal remains within the device’s specified voltage range at all operating states.

🧰

Test and Measurement Equipment

DG408CY+T can route eight test points, sources, or returns into a common instrument channel, helping compact test equipment cover more measurements without duplicating front-end hardware. Rail-to-rail handling, TTL/CMOS-compatible control, and low off leakage support a broad range of low- and medium-impedance analog test points. The 100-ohm maximum on-resistance should be included in the error budget for voltage measurements, while the 9-pC maximum charge injection should be considered in capacitance-sensitive or high-impedance tests. For production test fixtures, use short coaxial or guarded traces where appropriate, provide local decoupling, and keep external relay switching separate from the analog path when both technologies are required.

What is the DG408CY+T and what does it do?
The DG408CY+T is an 8-channel, single-ended CMOS analog multiplexer in a 16-SOIC package. It connects one of eight analog inputs to a common output and can also perform demultiplexing when signal flow is reversed. According to the Analog Devices DG408 datasheet, the device uses TTL/CMOS-compatible decoding and is intended for analog-signal routing, data acquisition, communication, and test systems.
What is the maximum on-resistance of DG408CY+T?
The DG408CY+T has a maximum on-resistance of 100 ohms. This resistance appears in the selected signal path and can create voltage errors when driving a finite load. The Analog Devices DG408 product page also states that on-resistance flatness is guaranteed to 8 ohms maximum, a useful characteristic for systems that require similar channel resistance as the address selection changes.
What supply voltages does DG408CY+T support?
The DG408CY+T supports a -20 V to -5 V supply or a 5 V to 30 V supply, as listed for the DG408CY+ ordering configuration. These are dual-supply operating ranges for bipolar analog signals. According to the Analog Devices datasheet information, the device also provides rail-to-rail signal handling, allowing selected signals to span the usable range of the applied analog supply.
Where can I download the DG408CY+T datasheet PDF?
The official DG408 product page at Analog Devices provides access to the manufacturer datasheet, product selection table, and supporting documentation. The family data sheet is identified as Data Sheet Rev. 4. For circuit implementation, use the pin configuration and electrical-characteristics tables from that document to verify address logic, supply sequencing, leakage, charge injection, and package details.
Where is the pinout for DG408CY+T?
The DG408CY+T pinout is defined in the pin-configuration section of the Analog Devices DG408 data sheet, Rev. 4. The component uses a 16-SOIC package with eight common or drain terminals, eight source or channel terminals, address inputs, enable control, and supply pins. The system-generated package diagram accompanies this page, while the manufacturer document should be used to assign every PCB net.
What is the operating temperature range of DG408CY+T?
The DG408CY+T is specified for a commercial operating temperature range of 0 to +70 degrees Celsius. This differs from DG408DY variants listed for operation from -40 to +85 degrees Celsius. The temperature-grade distinction is important for industrial equipment, automotive environments, and outdoor test systems because a mechanically similar package does not make every DG408 ordering code suitable for the same ambient range.
DG408CY+T vs DG408DY+T: which is better for industrial use?
DG408DY+T is the preferable choice when the surrounding electronics must operate from -40 to +85 degrees Celsius, while DG408CY+T is limited to 0 to +70 degrees Celsius. The DG408DY+T comparison identifies the same lower temperature limit and a 15 degrees Celsius higher upper limit. Both belong to the DG408 8-channel multiplexing family, but temperature requirements should be checked before PCB reuse.
Can DG408DY+T replace DG408CY+T on the same PCB?
DG408DY+T can serve as a pin-compatible alternative for a 16-SOIC DG408CY+T design when the increased temperature rating is acceptable and the complete device functions match. The principal documented difference is the operating range: -40 to +85 degrees Celsius for DG408DY+T versus 0 to +70 degrees Celsius for DG408CY+T. Confirm pin assignment, supply limits, and device-specific timing in the manufacturer documentation.
What is the best drop-in replacement for DG408CY+T?
DG408CY+ is the closest documented drop-in choice because it uses the same 16-SOIC DG408 configuration and matches the target’s 8:1, 100-ohm, commercial-temperature characteristics. DG408DY and DG408DY+T are also pin-compatible family alternatives when their wider temperature range is suitable. Use the Request a Quote form on this page to confirm exact suffix availability, package form, and production status.
When should I choose DG408CY+T over another DG408 variant?
Choose DG408CY+T when the design requires the improved DG408 8-channel multiplexer, a 16-SOIC footprint, 0 to +70 degrees Celsius operation, and up to 100-ohm on-resistance without requiring an extended-temperature grade. DG408DY and DG408DY+T are more appropriate when operation down to -40 degrees Celsius is mandatory. The choice should be based on temperature, exact pin configuration, and qualification requirements.
Is DG408CY+T suitable for audio and communication systems?
Yes, DG408CY+T is suitable for audio-signal routing and communication systems because it provides eight-channel analog selection, rail-to-rail signal handling, and TTL/CMOS-compatible controls. For low-level audio paths, calculate the settling error caused by charge injection and the channel resistance, and verify that the selected source impedance keeps the resulting signal error within the system budget.
How much power does DG408CY+T consume?
The Analog Devices DG408 product page specifies maximum power consumption of 1.25 mW for the DG408 family configuration. Actual dissipation depends on the selected supply voltages, logic state, and internal current path. Designers should use the electrical-characteristics table for operating-current and supply-current information and account for the additional thermal contribution of external circuit losses.
How does charge injection affect DG408CY+T designs?
Charge injection creates a transient voltage step when DG408CY+T changes channels, and the manufacturer specifies a maximum of 9 pC. In high-impedance or precision measurement circuits, this error can move the sampled voltage even when the mechanical switch timing is correct. Reduce sensitivity by using lower source impedance, suitable settling time, and input filtering, and verify the transient with an oscilloscope.
Where to buy DG408CY+T online and what is its lead time?
Use the Request a Quote form on this page to request DG408CY+T pricing, stock confirmation, and current lead time. The product is identified as a production device by Analog Devices and is listed as a 16-SOIC analog switch from the manufacturer’s authorized distribution network. A quote request allows the exact suffix, quantity, and delivery requirements to be checked together.
What are the key specifications of DG408CY+T that engineers should know?
The principal DG408CY+T specifications are 8:1 single-ended multiplexing, 100-ohm maximum on-resistance, 8-ohm maximum flatness, 9-pC maximum charge injection, 5-nA input-off leakage at +85 degrees Celsius, 1.25-mW maximum power consumption, TTL/CMOS-compatible logic, and operation from 0 to +70 degrees Celsius. It is packaged for surface mounting in a 16-SOIC package.

工程参考数据: DG408CY+T ——对比、设计指导和合规信息。

选型指南

Choose DG408CY+T for a 16-SOIC design that needs an improved 8-channel, single-ended CMOS multiplexer in the commercial temperature range from 0 to +70 degrees Celsius. It is a practical selection for room-temperature data-acquisition, audio-routing, communication, sample-and-hold, and test equipment where up to 100-ohm on-resistance and 9-pC maximum charge injection fit the error budget. DG408CY+ is the closest family alternative when the exact ordering suffix, packing form, and environmental requirements match. Select DG408DY or DG408DY+T when the same DG408 function is needed down to -40 degrees Celsius; their 15-degree-Celsius higher upper rating broadens industrial use but does not change the fundamental multiplexing role. Before reusing a PCB, confirm pin assignments, supply polarity, package dimensions, control timing, and qualification requirements in the manufacturer documentation.

与替代料对比

参数 本产品 DG408CY+ DG408DY+T DG408DY DG408EUE+T DG408DJZ
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Configuration 8:1 single-ended multiplexer 8:1 single-ended multiplexer 8-channel multiplexer 8-channel multiplexer 8-channel multiplexer 8-channel multiplexer

关键差异点

  • Improved 8-channel DG408 function with low charge injection (对比 DG408DY+T)
  • Commercial-temperature ordering option (对比 DG408DY+T)
  • Direct family-family PCB reuse (对比 DG408CY+)

设计说明

Treat channel switching as a charge-transfer event rather than an instantaneous ideal transition. The manufacturer specifies charge injection up to 9 pC. For a high-impedance source, the resulting error can be approximately the injected charge divided by the effective node capacitance. Include source resistance, input capacitance, and downstream filtering in the settling calculation, and verify the transient at the mux output with an oscilloscope.

Place the DG408CY+T close to the sources that share its output and keep all eight channel traces short and symmetric where practical. Route sensitive analog signals away from address and enable traces, provide a continuous ground reference beneath the analog path, and place decoupling near the supply pins. Keeping the common output compact reduces susceptibility to capacitive pickup and makes the measured settling behavior easier to control.

Do not treat the 16-SOIC outline as proof that every DG408 suffix has identical environmental requirements. DG408CY+T is a commercial-temperature part rated from 0 to +70 degrees Celsius, whereas DG408DY variants are identified for -40 to +85 degrees Celsius. Also check the supply polarity and selected-channel voltage before operation; incorrect logic levels or an out-of-range analog signal can exceed the switching conditions.

The family specification lists maximum power consumption of 1.25 mW, but the converter or amplifier connected to the mux can dominate system power and thermal design. Use separate, adequately decoupled analog and logic supplies where the architecture permits, and verify supply sequencing against the manufacturer guidelines. Keep the analog return current out of digital return paths to reduce supply noise appearing at the selected channel.

合规信息

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

RoHS compliance is indicated for DG408CY+T. No explicit REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement is included in the cited product information.

相关搜索

DG408CY+T datasheet DG408CY+T specifications DG408CY+T pinout DG408CY+T datasheet pdf DG408CY+T equivalent DG408CY+T replacement DG408CY+T cross reference DG408CY+T vs DG408DY+T DG408 16-SOIC multiplexer DG408 8:1 analog switch DG408CY+T data acquisition DG408CY+T audio routing Analog Devices DG408CY+T DG408CY+T price DG408CY+T stock

相关元器件 & 术语

Analog Devices Maxim Integrated DG408CY+T DG408CY+ DG408DY+T DG408DY DG408EUE+T DG408DJZ CMOS analog multiplexer analog switch multiplexer demultiplexer TTL CMOS on-resistance charge injection input off leakage rail-to-rail signal handling 16-SOIC SOIC package family surface mount SMD data acquisition sample-and-hold audio-signal routing
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情