DG408CY+T - 8:1 CMOS Analog Multiplexer | Analog Devices
부품 번호: DG408CY+T ✓ 활성DG408CY+T 개요
An analog multiplexer is a switching interface that routes multiple analog signals through one shared output path. The DG408 family belongs to the analog switch and multiplexer hierarchy, where reduced channel count, low on-resistance, low charge injection, and controlled leakage become important when precision signals must be selected without introducing excessive error. This device can also operate in a demultiplexing arrangement when signal flow is reversed.
Key characteristics include a maximum on-resistance of 100 ohms, 8 ohm maximum on-resistance flatness, and 9 pC maximum charge injection. Input off leakage is limited to 5 nA at +85 degrees Celsius, while the logic section accepts TTL/CMOS-compatible control levels. ESD protection exceeds 2000 V, and low power consumption is specified at a maximum of 1.25 mW. Rail-to-rail signal handling supports operation across the supplied analog signal range.
The internal design uses eight CMOS analog switches, a digital decoder for channel selection, a voltage reference for logic thresholds, and an enable input for device selection when several multiplexers share a bus. Analog Devices describes the DG408 and DG409 as pin-compatible plug-in upgrades for the industry-standard DG408 and DG409 families, while Renesas identifies them as drop-in replacements for popular DG508A and DG509A devices.
Typical uses include audio-signal routing, communication systems, data-acquisition equipment, guidance and control systems, sample-and-hold circuits, and test equipment. The 16-SOIC package supports conventional surface-mount assembly, and the DG408CY+T commercial-temperature ordering code targets operation from 0 to +70 degrees Celsius.
Designers should account for charge injection during channel transitions and keep sensitive analog traces short and adequately decoupled. Supply rails, logic thresholds, signal amplitude, and the selected input channel must remain within the manufacturer’s operating limits. Because the device can conduct equally well in either direction, it is suitable for both multiplexing and demultiplexing.
This page combines manufacturer specifications, package and temperature details, drop-in replacement information, and application-focused engineering guidance. It also highlights the measurable differences among compatible DG408 variants so that PCB reuse can be evaluated without overlooking temperature grade, package construction, or channel-selection requirements.
드롭인 대체품: DG408CY+T — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: DG408CY+T (동일 폼 팩터 및 풋프린트) — 차이점: Package, Channel Matching, Charge Injection, Configuration, ESD Protection.
DG408CY+
✅ 드롭인가격 문의
데이터시트 보기 →DG408DY+T
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DG408DY+
✅ 드롭인가격 문의
데이터시트 보기 →DG408EUE+T
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DG408DJZ
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DG408CY+T 사양
| Configuration | 1 circuit, 8:1 single-ended multiplexer |
| Number of Channels | 8 channels |
| Maximum On-Resistance | 100 ohm |
| On-Resistance Flatness | 8 ohm maximum |
| Charge Injection | 9 pC maximum |
| Input Off Leakage | 5 nA maximum at +85 degrees Celsius |
| Maximum Input Leakage | 100 ohm maximum |
| Power Consumption | 1.25 mW maximum |
| Signal Handling | Rail-to-rail |
| Logic Compatibility | TTL/CMOS compatible |
| ESD Protection | >2000 V |
| Supply Voltage Range | -20 V to -5 V or 5 V to 30 V |
| 동작 온도 | 0 degrees Celsius to +70 degrees Celsius |
| Temperature Grade | Commercial |
| 패키지 | 16-SOIC, 4.4 mm nominal body width |
| 실장 유형 | Surface mount |
| Package Shape | Rectangular |
| RoHS 상태 | Compliant |
DG408CY+T rectangular 핀 구성 가이드
DG408CY+T(rectangular 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: DG408CY+T.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
DG408CY+T 적합 용도: 6 애플리케이션s: Audio Signal Routing, Data Acquisition Systems, Communication Systems, Sample-and-Hold Circuits, Guidance and Control Systems, Test and Measurement Equipment.
Audio Signal Routing
DG408CY+T is well suited to selecting among several audio inputs when a system must preserve usable signal amplitude across a shared output path. Its 100-ohm maximum on-resistance limits voltage loss into moderate loads, while rail-to-rail signal handling supports direct routing across the applied analog supply range. Eight channels can replace multiple discrete selectors and reduce routing complexity in audio-signal routing equipment. Designers should still budget for the 9-pC maximum charge injection when channels change during sensitive transitions. Practical layouts should keep the common output short, provide a stable return path, and place any required filtering after the multiplexer so switching transients do not feed back into upstream stages.
추천
Data Acquisition Systems
DG408CY+T can route up to eight external measurements into one data-acquisition channel, reducing the number of front-end inputs required by a controller or converter. The 5-nA maximum input-off leakage at +85 degrees Celsius is especially useful when the measured source has high impedance, because leakage from unselected channels can otherwise create errors. The 8:1 configuration also permits demultiplex operation when returning multiple switched signals through one conductor. For accurate acquisition, allow the circuit to settle after each address change, include anti-alias filtering suited to the measurement bandwidth, and verify the combined effects of source impedance, switch resistance, and charge injection against the required accuracy.
추천
Communication Systems
DG408CY+T provides analog channel selection for communication equipment that must route transmit, receive, feedback, or test paths through a shared analog stage. TTL/CMOS-compatible address and enable controls simplify coordination with standard digital logic, while the eight-channel arrangement offers more routing flexibility than a single-pole selector. The 100-ohm maximum on-resistance should be evaluated against the input impedance of the following RF or baseband stage; it is generally more appropriate for low-frequency and instrumentation paths than for impedance-sensitive high-frequency designs. Control traces should remain short, and supply bypassing should be located close to the device to prevent logic or supply transients from coupling into the selected channel.
추천
Sample-and-Hold Circuits
DG408CY+T can select one of eight source signals for a sample-and-hold or pulsed-measurement system, allowing one high-value converter or amplifier to serve multiple inputs. Its low leakage of 5 nA maximum at +85 degrees Celsius helps preserve accuracy when sampling high-impedance sources, and its 8:1 arrangement supports shared acquisition hardware. The dominant engineering consideration is charge injection: the specified 9-pC maximum can create a voltage step whenever the address changes. Use sufficiently long acquisition times, source impedances that limit injected-error gain, and a sampling architecture that isolates the source during the transition. Verify the complete settling behavior with the source impedance and front-end capacitance used in the final design.
추천
Guidance and Control Systems
DG408CY+T is applicable when a guidance or control system must select among several sensor, feedback, or command signals for common processing. Eight channels reduce the routing burden in compact control assemblies, and the commercial 0-to-+70-degree-Celsius grade is appropriate for indoor laboratory, industrial enclosure, or room-temperature equipment. The device’s ESD protection above 2000 V adds useful robustness, but system designers must still provide appropriate external protection for long cables and field wiring. Use a common ground reference, keep high-impedance sensor paths away from switching controls, and include diagnostics that identify which channel is selected. Confirm that every multiplexed signal remains within the device’s specified voltage range at all operating states.
추천
Test and Measurement Equipment
DG408CY+T can route eight test points, sources, or returns into a common instrument channel, helping compact test equipment cover more measurements without duplicating front-end hardware. Rail-to-rail handling, TTL/CMOS-compatible control, and low off leakage support a broad range of low- and medium-impedance analog test points. The 100-ohm maximum on-resistance should be included in the error budget for voltage measurements, while the 9-pC maximum charge injection should be considered in capacitance-sensitive or high-impedance tests. For production test fixtures, use short coaxial or guarded traces where appropriate, provide local decoupling, and keep external relay switching separate from the analog path when both technologies are required.
추천
추천 제품 요약
엔지니어링 참조 데이터: DG408CY+T — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DG408CY+ | DG408DY+T | DG408DY | DG408EUE+T | DG408DJZ |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Configuration | 8:1 single-ended multiplexer | 8:1 single-ended multiplexer | 8-channel multiplexer | 8-channel multiplexer | 8-channel multiplexer | 8-channel multiplexer |
주요 차별점
- Improved 8-channel DG408 function with low charge injection (vs DG408DY+T)
- Commercial-temperature ordering option (vs DG408DY+T)
- Direct family-family PCB reuse (vs DG408CY+)
설계 노트
Treat channel switching as a charge-transfer event rather than an instantaneous ideal transition. The manufacturer specifies charge injection up to 9 pC. For a high-impedance source, the resulting error can be approximately the injected charge divided by the effective node capacitance. Include source resistance, input capacitance, and downstream filtering in the settling calculation, and verify the transient at the mux output with an oscilloscope.
Place the DG408CY+T close to the sources that share its output and keep all eight channel traces short and symmetric where practical. Route sensitive analog signals away from address and enable traces, provide a continuous ground reference beneath the analog path, and place decoupling near the supply pins. Keeping the common output compact reduces susceptibility to capacitive pickup and makes the measured settling behavior easier to control.
Do not treat the 16-SOIC outline as proof that every DG408 suffix has identical environmental requirements. DG408CY+T is a commercial-temperature part rated from 0 to +70 degrees Celsius, whereas DG408DY variants are identified for -40 to +85 degrees Celsius. Also check the supply polarity and selected-channel voltage before operation; incorrect logic levels or an out-of-range analog signal can exceed the switching conditions.
The family specification lists maximum power consumption of 1.25 mW, but the converter or amplifier connected to the mux can dominate system power and thermal design. Use separate, adequately decoupled analog and logic supplies where the architecture permits, and verify supply sequencing against the manufacturer guidelines. Keep the analog return current out of digital return paths to reduce supply noise appearing at the selected channel.
규정 준수 정보
RoHS compliance is indicated for DG408CY+T. No explicit REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement is included in the cited product information.