DG411CUE+ - Quad 45Ω SPST Analog Switch | Analog Devices
料号: DG411CUE+ ✓ 量产中DG411CUE+ 概述
An analog switch is an electrically controlled semiconductor device that connects or disconnects signal paths with minimal disturbance to the signal being routed. The SPST designation identifies a single-pole, single-throw configuration, while the DG411CUE+ provides four such switch circuits in one package. In the signal-chain hierarchy, it belongs to the analog switch and multiplexer family within interface ICs, where it sits between sensors, amplifiers, data converters, and external instrumentation.
Key characteristics include a 45 Ω maximum on-resistance, 1:1 signal routing, four switch circuits, and bidirectional analog-channel operation. Analog Devices states that the redesigned DG411, DG412, and DG413 family provides improved matching between switches, with a maximum on-resistance matching figure of 3 Ω, and guaranteed on-resistance flatness across the signal range of no more than 4 Ω. These characteristics help reduce channel-to-channel variation and distortion when routing precision signals.
The DG411CUE+ uses CMOS-based switching elements controlled by digital logic inputs. Because its channels are bidirectional, the switched nodes can carry signals in either direction, subject to the voltage and current limits defined by the manufacturer datasheet. Its 16-pin TSSOP surface-mount package supports compact PCB layouts while providing separate control and signal connections for four analog switches.
Typical uses include multimeter and oscilloscope input routing, automated test equipment, sample-and-hold systems, industrial measurement interfaces, and audio or communication signal-path switching. In these applications, the four independent channels can reduce the number of discrete relays or mechanical switch elements needed when a design requires several signal connections to be rerouted under digital control.
PCB design should keep the analog signal pins and associated traces away from high-current switching nodes and clocked digital circuitry. Follow the Analog Devices DG411 datasheet pin description and typical application circuits for the exact control logic, supply requirements, input voltage limits, and recommended external components. Confirm signal amplitude and switching speed against the device limits before finalizing the routing design.
This product page combines the manufacturer’s DG411 family information with package, ordering, regulatory, and cross-reference details. It also organizes practical selection guidance, comparison parameters, and PCB-focused design notes to help engineers evaluate the DG411CUE+ for new analog-routing designs.
直接替换替代料: DG411CUE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
DG411CUE
✅ 直接替换📋 参考替代料(不在目录中)
DG411CUE+T
✅ 直接替换📋 参考替代料(不在目录中)
DG411CUE-T
✅ 直接替换📋 参考替代料(不在目录中)
DG411CUE+ 最大额定值与电气特性
| Switch Type | SPST (single-pole, single-throw) |
| Number of Circuits | 4 circuits |
| Number of Channels | 4 channels |
| On Resistance | 45 Ω maximum |
| Signal Configuration | 1:1 |
| Signal Direction | Bidirectional |
| On-Resistance Matching | 3 Ω maximum between switches |
| On-Resistance Flatness | 4 Ω maximum over the signal range |
| 工作温度范围 | 0°C to +70°C |
| Package Type | 16-pin TSSOP (MO-153AB) |
| Package Body Width | 4.4 mm |
| Package Shape | Rectangular |
| 安装方式 | Surface mount |
| Number of Terminals | 16 terminals |
| 生命周期状态 | Production |
| RoHS 状态 | Compliant |
DG411CUE+ rectangular 引脚配置指南
DG411CUE+(rectangular 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: DG411CUE+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DG411CUE+ 适用于 6 应用s: Multimeter Signal Routing, Automated Test Equipment, Oscilloscope Input Switching, Sample-and-Hold Systems, Industrial Sensor Interfaces, Audio Signal Path Switching.
Multimeter Signal Routing
The DG411CUE+ is suitable for routing measurement signals between input terminals and internal circuitry because it provides four independent SPST paths with bidirectional operation. Its 45 Ω maximum on-resistance and 3 Ω maximum switch-to-switch matching can help limit insertion-loss variation between selected channels, while the 1:1 configuration preserves the signal path topology. A common arrangement uses control logic to connect a source, return, and guard path in sequence. Before implementation, verify the permitted signal and logic voltages, switching speed, leakage, and off-isolation in the Analog Devices DG411 data sheet.
Automated Test Equipment
In automated test equipment, the DG411CUE+ can connect test stimuli and return signals under instrument-control logic without using multiple bulky mechanical relays. Four separately controlled SPST switches support repeatable routing of input, output, and guard lines, and the 45 Ω maximum on-resistance provides a defined basis for insertion-loss analysis. Bidirectional channels are useful when a test node can either drive or receive a signal. Keep copper traces short, provide a stable return path, and confirm timing against the control system because the switch transition characteristics must satisfy the measurement settling window.
Oscilloscope Input Switching
The DG411CUE+ can route selected oscilloscope channels between test points, buffers, and calibration networks. Its four SPST switches, bidirectional paths, and 45 Ω maximum on-resistance allow several measurement connections to be managed by digital control in a compact 16-pin TSSOP package. Improved matching of 3 Ω maximum between switches helps reduce channel-dependent attenuation, which is valuable when comparing similar waveforms. Account for capacitance, leakage, and switching time when budgeting measurement bandwidth, and keep sensitive input traces away from adjacent switching and control nets.
Sample-and-Hold Systems
A sample-and-hold design can use the DG411CUE+ to connect and isolate a sensor or source node during acquisition and processing intervals. The SPST topology provides straightforward signal isolation, while bidirectional operation supports configurations where the held node is charged from one path and read through another. The 45 Ω maximum on-resistance must be included in the source impedance and settling calculations because it forms part of the charging path. Use the manufacturer’s switch timing, leakage, capacitance, and maximum signal ratings to determine the required acquisition time and external compensation components.
Industrial Sensor Interfaces
The DG411CUE+ can route sensor signals between conditioning channels, calibration references, and diagnostic paths in an industrial interface. Four independently controlled SPST circuits give the controller a compact way to select multiple analog inputs without requiring one relay per channel, and the 0°C to +70°C rating covers many ambient-controlled equipment installations. Bidirectional switching is beneficial for two-wire sensors and shared buses. The design must protect all switched nodes from exceeding the manufacturer’s absolute maximum ratings and should isolate high-energy industrial wiring from sensitive analog traces.
Audio Signal Path Switching
The DG411CUE+ can select among audio or low-frequency signal sources in compact test and control equipment. Its bidirectional SPST channels support source-to-destination routing, while the 45 Ω maximum on-resistance must be considered alongside the source and load impedance to establish expected insertion loss. The family’s 3 Ω maximum matching and 4 Ω maximum flatness specifications help reduce channel-dependent level differences. Place the device away from motor, relay, and switching-power stages, maintain a quiet ground reference, and verify distortion, bandwidth, and signal limits against the Analog Devices data sheet.
工程参考数据: DG411CUE+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DG411CUE | DG411CUE+T | DG411CUE-T |
|---|---|---|---|---|
| Package | 16-pin TSSOP (MO-153AB) | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Switch Type | SPST | SPST | SPST | SPST |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Signal Configuration | 1:1 | 1:1 | 1:1 | 1:1 |
| On Resistance | 45 Ω maximum | 45 Ω maximum | 45 Ω maximum | 45 Ω maximum |
| Signal Direction | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
| On-Resistance Matching | 3 Ω maximum between switches | 3 Ω maximum between switches | 3 Ω maximum between switches | 3 Ω maximum between switches |
| On-Resistance Flatness | 4 Ω maximum over the signal range | 4 Ω maximum over the signal range | 4 Ω maximum over the signal range | 4 Ω maximum over the signal range |
关键差异点
- Four-channel integration in a single TSSOP package (对比 DG411CUE)
- Consistent bidirectional 1:1 signal routing (对比 DG411CUE+T)
- Improved channel matching and flatness (对比 DG411CUE-T)
设计说明
Treat the 45 Ω maximum on-resistance as part of the complete switched signal path. Calculate the resulting divider with the source impedance, load impedance, switch capacitance, and any input bias current rather than checking the switch in isolation. For measurement and audio paths, preserve a continuous ground reference and compare the 3 Ω maximum switch-to-switch matching when defining acceptable channel-to-channel level variation.
Place the DG411CUE+ close to the signals it routes and connect the package ground reference directly to the relevant analog ground plane. Keep switched-node traces away from clocks, relay drivers, inductors, and high-current power paths. Use the pin-description and package drawing in the Analog Devices DG411 data sheet when assigning the 16 terminals; do not derive control polarity from a similarly named switch.
Do not exceed the published limits for supply voltage, analog signal voltage, switch current, or absolute maximum conditions. Because the DG411CUE+ is bidirectional, both directions of a switched node must remain inside the operating envelope. Also account for off-isolation and leakage when a disconnected source can remain energized, and verify the settling interval required by precision acquisition or measurement systems.
合规信息
The product comparison information identifies the DG411CUE+ as RoHS compliant. No additional REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statements are stated for this exact ordering configuration.