DG428DN - Latchable 8:1 Analog Multiplexer | Vishay | ATE
料号: DG428DN ✓ 量产中DG428DN 概述
An analog multiplexer is an interface IC that connects one of several analog inputs to a common output according to a digital address. The DG428DN belongs to the broader multiplexer-switch and signal-routing hierarchy, where latched address inputs reduce the number of control signals required from a microprocessor. Its differential configuration allows two switch pairs to route paired signals, supporting balanced measurements and reducing common-mode routing complexity.
The device provides a maximum on-resistance of 100 ohms, an on-state switching time of 225 ns, an off-state switching time of 300 ns, and an isolation value of 75 dB. Onboard TTL-compatible address latches permit the selected channel to remain stable between control updates. Break-before-make operation prevents two channels from being connected simultaneously during a transition, which is important for external equipment, instrumentation, and measurement systems.
The DG428DN can operate with positive or negative supply voltages and also supports single-supply operation. Its absolute maximum voltage rating extends to 44 V. An epitaxial layer is designed to reduce latch-up risk, while low power consumption of 0.3 mW supports power-conscious acquisition and control systems. The address interface is compatible with microprocessor buses, reducing external logic and board-space requirements.
Typical applications include data-acquisition systems, automatic test equipment, process-control equipment, avionics, instrumentation, and multiplexed sensor interfaces. A single package can route eight single-ended channels or four differential channels, making it useful where several physical inputs must share one converter, amplifier, or measurement front end.
When laying out a board, keep the selected analog path short and place protection networks away from the multiplexer pins. Confirm signal swing, supply polarity, and break-before-make behavior before assigning channels to external equipment. The complete pin and package details should be checked against the Vishay datasheet before layout release.
This page consolidates the DG428DN electrical characteristics, package information, replacement guidance, comparison data, and practical application guidance. It is intended to help engineers evaluate the device for multiplexed analog acquisition, test, control, and signal-routing systems.
直接替换替代料: DG428DN ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
DG428DN-E3
✅ 直接替换📋 参考替代料(不在目录中)
DG428DN 规格参数
| Configuration | 8:1 single-ended or 4:1 differential |
| Number of Switches | 8 |
| On-Resistance | 100 ohms maximum |
| Supply Voltage Range | -15 V to +15 V |
| Absolute Maximum Voltage | 44 V |
| Turn-On Time | 225 ns |
| Turn-Off Time | 300 ns |
| Isolation | 75 dB |
| 工作温度范围 | -40 °C to +85 °C |
| Low Power Consumption | 0.3 mW |
| Address Latches | Onboard, TTL-compatible |
| Switching Sequence | Break-before-make |
| Single-Supply Operation | Supported |
| Latch-Up Protection | Epitaxial layer |
| 封装 | 20-pin PLCC, 9 mm x 9 mm |
| 安装类型 | Surface mount |
DG428DN 20-pin plcc, 9 mm x 9 mm 引脚配置指南
DG428DN(20-pin plcc, 9 mm x 9 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: DG428DN.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DG428DN 适用于 6 应用s: Data Acquisition Systems, Automatic Test Equipment, Process Control Systems, Avionics Signal Routing, Multiplexed Sensor Interfaces, Precision Instrumentation.
Data Acquisition Systems
The DG428DN fits multiplexed data-acquisition front ends that route up to eight single-ended inputs or four differential input pairs to a shared converter or amplifier. Its 100-ohm maximum on-resistance, 75 dB isolation, and 225 ns turn-on time support practical selection of precision and moderate-bandwidth signals. Onboard TTL-compatible address latches hold the selected channel without requiring continuous processor control. Place the mux close to the source connectors, keep ground returns short, and verify the input network against the switch impedance and acquisition time budget.
推荐
Automatic Test Equipment
The DG428DN is suitable for automatic test equipment that connects multiple test points to a shared measurement channel. Its eight single-ended or four differential configurations reduce repetitive fixture wiring, while break-before-make switching prevents unintended channel overlap during address transitions. The 300 ns turn-off time and 225 ns turn-on time help control sequencing delays in automated measurements. Designers should include isolation, protection, and settling time in the test timing budget, especially for high-impedance nodes where the 100-ohm maximum on-resistance can influence measurement accuracy.
推荐
Process Control Systems
The DG428DN can route sensor and actuator signals in process-control equipment where multiple analog inputs share one controller interface. Its latched address inputs reduce the number of processor outputs needed to maintain a channel selection, and the -15 V to +15 V supply range supports conventional bipolar process-control signal levels. Break-before-make operation helps maintain predictable connection sequences. Engineers should verify common-mode limits, grounding strategy, isolation requirements, and fail-safe behavior during power transitions before connecting field-wired signals.
推荐
Avionics Signal Routing
The DG428DN is applicable to avionics and airborne instrumentation that require several analog signals to be routed through a compact, latched multiplexer. Its eight single-ended or four differential channels support shared measurement resources, while the 75 dB isolation specification helps limit unwanted interaction between channels. The PLCC package supports surface-mount assembly and compact PCB layouts. For airborne use, confirm the exact orderable suffix, environmental qualification, reliability documentation, and applicable installation requirements before production release.
推荐
Multiplexed Sensor Interfaces
The DG428DN can consolidate thermocouple, bridge, potentiometer, or other multiplexed sensor inputs when their voltage, impedance, and bandwidth remain within the device ratings. Four differential channels are useful for balanced bridge or paired-sensor measurements, while eight single-ended channels suit simpler sensor racks. The latched address interface simplifies deterministic acquisition timing, and the low 0.3 mW power figure supports compact control systems. Use short, shielded routes and account for switch resistance, leakage, settling time, and sensor-source impedance.
推荐
Precision Instrumentation
The DG428DN supports precision instrumentation that routes a limited number of high-value analog inputs to a shared amplifier, reference, or measurement channel. Its 100-ohm maximum on-resistance makes source-impedance budgeting important, while the 75 dB isolation value and break-before-make behavior help control inter-channel effects. Latched address inputs simplify synchronous measurement sequencing and reduce software overhead. For best performance, minimize trace length around the selected paths, maintain a stable analog ground plane, and include the switch impedance and settling interval in the instrument error calculation.
推荐
推荐产品汇总
工程参考数据: DG428DN ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DG428DN-E3 |
|---|---|---|
| Brand | Vishay Intertechnology | Vishay Intertechnology |
| Package | 20-pin PLCC (9 x 9 mm) | 20-pin PLCC (9 x 9 mm) |
| Configuration | 8:1 single-ended or 4:1 differential | 8:1 single-ended or 4:1 differential |
| Number of Switches | 8 | 8 |
| On-Resistance | 100 ohms maximum | 100 ohms maximum |
| Supply Voltage Range | -15 V to +15 V | -15 V to +15 V |
| Turn-On Time | 225 ns | 225 ns |
| Turn-Off Time | 300 ns | 300 ns |
| Isolation | 75 dB | 75 dB |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C |
| Address Latches | Onboard, TTL-compatible | Onboard, TTL-compatible |
| Switching Sequence | Break-before-make | Break-before-make |
关键差异点
- Supports both single-ended and differential routing in one device (对比 ADG428BPZ)
- Onboard latches reduce processor interface overhead (对比 ADG428BPZ)
- Break-before-make switching protects channel isolation (对比 ADG428BPZ)
- Documented 100-ohm maximum on-resistance (对比 DG428DN-E3)
设计说明
Do not treat the ADG428BPZ as a board-level drop-in replacement for the DG428DN. Although both provide an 8:1 multiplexing function and comparable 100-ohm maximum on-resistance, the DG428DN uses a 20-pin PLCC package while the ADG428BPZ uses a different package. Confirm the complete pin map, supply arrangement, control logic, and electrical limits in the manufacturer datasheet before approving a substitution or starting a PCB layout.
Route each analog channel and the common output as short and direct as practical, with a continuous ground plane beneath the PLCC footprint where the package and application permit. Keep digital address and latch traces away from sensitive analog inputs to reduce capacitive coupling. Because the specified maximum on-resistance is 100 ohms, include switch resistance and source impedance in the settling-time and gain-error budget, particularly for high-impedance sensors.
Use the break-before-make behavior as part of the system timing design. Allow the turn-off interval of 300 ns before expecting a newly selected channel to begin its 225 ns turn-on interval, and add amplifier or converter acquisition time afterward. For external test equipment, use controlled impedance paths and verify that transient interaction during channel changes remains acceptable to the equipment under test.
Design the dual-supply rails with the correct polarity and keep their magnitude within the -15 V to +15 V operating range; the 44 V value is an absolute maximum rating, not a recommended operating condition. Decouple the supply pins locally, provide a stable analog return, and check startup behavior for signals that may remain connected while the address latch or enable state is undefined.
合规信息
The DG428DN-E3 ordering suffix may relate to a lead-free finish, but no exact compliance declaration for DG428DN was found. Environmental qualification for automotive use must be confirmed for the selected orderable suffix.