Vishay Intertechnology

DG428DN - Latchable 8:1 Analog Multiplexer | Vishay | ATE

부품 번호: DG428DN ✓ 활성
-15 V to +15 V Vdss 100 ohms maximum Rds(on) 20-pin PLCC, 9 mm x 9 mm Package
MOQ: 1 |

DG428DN 개요

The Vishay DG428DN is a latchable 8-channel single-ended or 4-channel differential analog multiplexer with a maximum on-resistance of 100 ohms, operating from -15 V to +15 V in a 20-pin PLCC package measuring 9 x 9 mm. It combines eight analog inputs, onboard TTL-compatible address latches, break-before-make switching, and low power consumption for processor-controlled signal routing.

An analog multiplexer is an interface IC that connects one of several analog inputs to a common output according to a digital address. The DG428DN belongs to the broader multiplexer-switch and signal-routing hierarchy, where latched address inputs reduce the number of control signals required from a microprocessor. Its differential configuration allows two switch pairs to route paired signals, supporting balanced measurements and reducing common-mode routing complexity.

The device provides a maximum on-resistance of 100 ohms, an on-state switching time of 225 ns, an off-state switching time of 300 ns, and an isolation value of 75 dB. Onboard TTL-compatible address latches permit the selected channel to remain stable between control updates. Break-before-make operation prevents two channels from being connected simultaneously during a transition, which is important for external equipment, instrumentation, and measurement systems.

The DG428DN can operate with positive or negative supply voltages and also supports single-supply operation. Its absolute maximum voltage rating extends to 44 V. An epitaxial layer is designed to reduce latch-up risk, while low power consumption of 0.3 mW supports power-conscious acquisition and control systems. The address interface is compatible with microprocessor buses, reducing external logic and board-space requirements.

Typical applications include data-acquisition systems, automatic test equipment, process-control equipment, avionics, instrumentation, and multiplexed sensor interfaces. A single package can route eight single-ended channels or four differential channels, making it useful where several physical inputs must share one converter, amplifier, or measurement front end.

When laying out a board, keep the selected analog path short and place protection networks away from the multiplexer pins. Confirm signal swing, supply polarity, and break-before-make behavior before assigning channels to external equipment. The complete pin and package details should be checked against the Vishay datasheet before layout release.

This page consolidates the DG428DN electrical characteristics, package information, replacement guidance, comparison data, and practical application guidance. It is intended to help engineers evaluate the device for multiplexed analog acquisition, test, control, and signal-routing systems.

드롭인 대체품: DG428DN — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

DG428DN-E3

✅ 드롭인
📦 20-pin PLCC (9 x 9 mm)
Same Vishay DG428 function and 20-pin PLCC construction; ordering suffix denotes a distinct finish or qualification designation, with electrical compatibility requiring final datasheet confirmation

📋 참조 대체품 (카탈로그에 없음)

DG428DN 사양

Configuration 8:1 single-ended or 4:1 differential
Number of Switches 8
On-Resistance 100 ohms maximum
Supply Voltage Range -15 V to +15 V
Absolute Maximum Voltage 44 V
Turn-On Time 225 ns
Turn-Off Time 300 ns
Isolation 75 dB
동작 온도 범위 -40 °C to +85 °C
Low Power Consumption 0.3 mW
Address Latches Onboard, TTL-compatible
Switching Sequence Break-before-make
Single-Supply Operation Supported
Latch-Up Protection Epitaxial layer
패키지 20-pin PLCC, 9 mm x 9 mm
실장 유형 Surface mount

DG428DN 20-pin plcc, 9 mm x 9 mm 핀 구성 가이드

DG428DN(20-pin plcc, 9 mm x 9 mm 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

DG428DN의 20-pin plcc, 9 mm x 9 mm 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: DG428DN.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

DG428DN 적합 용도: 6 애플리케이션s: Data Acquisition Systems, Automatic Test Equipment, Process Control Systems, Avionics Signal Routing, Multiplexed Sensor Interfaces, Precision Instrumentation.

📊

Data Acquisition Systems

The DG428DN fits multiplexed data-acquisition front ends that route up to eight single-ended inputs or four differential input pairs to a shared converter or amplifier. Its 100-ohm maximum on-resistance, 75 dB isolation, and 225 ns turn-on time support practical selection of precision and moderate-bandwidth signals. Onboard TTL-compatible address latches hold the selected channel without requiring continuous processor control. Place the mux close to the source connectors, keep ground returns short, and verify the input network against the switch impedance and acquisition time budget.

🏭

Automatic Test Equipment

The DG428DN is suitable for automatic test equipment that connects multiple test points to a shared measurement channel. Its eight single-ended or four differential configurations reduce repetitive fixture wiring, while break-before-make switching prevents unintended channel overlap during address transitions. The 300 ns turn-off time and 225 ns turn-on time help control sequencing delays in automated measurements. Designers should include isolation, protection, and settling time in the test timing budget, especially for high-impedance nodes where the 100-ohm maximum on-resistance can influence measurement accuracy.

🏭

Process Control Systems

The DG428DN can route sensor and actuator signals in process-control equipment where multiple analog inputs share one controller interface. Its latched address inputs reduce the number of processor outputs needed to maintain a channel selection, and the -15 V to +15 V supply range supports conventional bipolar process-control signal levels. Break-before-make operation helps maintain predictable connection sequences. Engineers should verify common-mode limits, grounding strategy, isolation requirements, and fail-safe behavior during power transitions before connecting field-wired signals.

✈️

Avionics Signal Routing

The DG428DN is applicable to avionics and airborne instrumentation that require several analog signals to be routed through a compact, latched multiplexer. Its eight single-ended or four differential channels support shared measurement resources, while the 75 dB isolation specification helps limit unwanted interaction between channels. The PLCC package supports surface-mount assembly and compact PCB layouts. For airborne use, confirm the exact orderable suffix, environmental qualification, reliability documentation, and applicable installation requirements before production release.

🧩

Multiplexed Sensor Interfaces

The DG428DN can consolidate thermocouple, bridge, potentiometer, or other multiplexed sensor inputs when their voltage, impedance, and bandwidth remain within the device ratings. Four differential channels are useful for balanced bridge or paired-sensor measurements, while eight single-ended channels suit simpler sensor racks. The latched address interface simplifies deterministic acquisition timing, and the low 0.3 mW power figure supports compact control systems. Use short, shielded routes and account for switch resistance, leakage, settling time, and sensor-source impedance.

🔧

Precision Instrumentation

The DG428DN supports precision instrumentation that routes a limited number of high-value analog inputs to a shared amplifier, reference, or measurement channel. Its 100-ohm maximum on-resistance makes source-impedance budgeting important, while the 75 dB isolation value and break-before-make behavior help control inter-channel effects. Latched address inputs simplify synchronous measurement sequencing and reduce software overhead. For best performance, minimize trace length around the selected paths, maintain a stable analog ground plane, and include the switch impedance and settling interval in the instrument error calculation.

What are the key specifications of DG428DN that engineers should know?
The DG428DN is an 8-channel latchable analog multiplexer with a maximum on-resistance of 100 ohms, a -15 V to +15 V supply range, 225 ns turn-on time, 300 ns turn-off time, and 75 dB isolation. According to the Vishay datasheet, it can operate as an 8:1 single-ended or 4:1 differential switch in a 20-pin PLCC package. Its onboard TTL-compatible latches and break-before-make action are the most important features for bus-controlled acquisition and test systems.
Where can I download the DG428DN datasheet PDF?
The official Vishay DG428DN datasheet PDF is available from the Vishay documentation link for document 70063. According to the manufacturer datasheet, it describes the 8-channel single-ended and 4-channel differential configurations, address latches, electrical characteristics, switching behavior, and absolute maximum ratings. Use the manufacturer PDF for final pin assignments, timing limits, and application details before releasing a PCB design.
Where is the DG428DN pinout and package information?
The DG428DN uses a 20-pin PLCC package measuring 9 mm by 9 mm, but the manufacturer pin-description table must be used when assigning PCB tracks. The package drawing and pin table are contained in the Vishay DG428DN datasheet. Because the PLCC package is not represented by a dedicated package-diagram library entry on this page, the interactive pinout is not reproduced; verify every analog, supply, ground, address, latch, and enable connection against the datasheet.
How does the DG428DN switch eight channels?
The DG428DN uses three binary address inputs to select one of eight single-ended channels or one of four differential channels. Its onboard address latches hold the selection until new control data is written, reducing the number of processor interface lines required. According to the Vishay datasheet, break-before-make operation ensures that the old channel is disconnected before the new channel is connected, which helps prevent overlap between external instrument channels.
What is the difference between DG428DN and DG428DN-E3?
The DG428DN and DG428DN-E3 are both identified as 20-pin PLCC versions of the Vishay multiplexer, but the -E3 ordering suffix denotes a distinct manufacturer finish or qualification designation that must be checked for the exact assembly. The DG428DN-E3 listing specifically identifies PLCC-20 construction. For a new design, confirm ordering information, lifecycle status, and environmental declarations for the suffix intended for production rather than treating the suffix as electrically interchangeable by default.
Can ADG428BPZ replace the DG428DN on an existing PCB?
No, the ADG428BPZ is not a direct drop-in replacement for the DG428DN because it uses a different package. The Vishay DG428DN is specified in a 20-pin PLCC package, while the cross-reference comparison identifies ADG428BPZ as functionally similar but differently packaged. Both devices are described as 8:1 analog multiplexers with comparable 100-ohm maximum on-resistance, but changing package would require a PCB redesign rather than a drop-in substitution.
What is the best drop-in replacement for DG428DN?
The DG428DN-E3 is the closest documented drop-in candidate because it is also identified as a Vishay 20-pin PLCC multiplexer with the same DG428 function. A definitive replacement decision still requires confirmation of pinout, electrical ratings, temperature range, marking, and ordering qualifications. Do not use the ADG428BPZ as a drop-in replacement because its package differs, even though its 8:1 switching function and 100-ohm maximum on-resistance are comparable.
When should I choose DG428DN instead of a non-latching analog switch?
Choose the DG428DN when the selected channel must remain stable without continuous address outputs or repeated software writes. Its onboard TTL-compatible latches are useful with microprocessor-controlled data-acquisition, process-control, avionics, and automatic test equipment. If the host can continuously drive the address pins and board space is more constrained, a simpler non-latched multiplexer may be sufficient, provided break-before-make behavior and the required switching speed are acceptable.
Is DG428DN suitable for differential sensor acquisition?
Yes, the DG428DN supports a four-channel differential configuration in addition to its eight-channel single-ended mode. This allows paired signals to be routed through matched switch paths to a differential amplifier, converter, or measurement front end. According to the Vishay datasheet, the device includes low on-resistance and 75 dB isolation, but system accuracy still depends on matching external networks, keeping analog routing compact, and ensuring common-mode voltage and supply limits remain within the device ratings.
How much power does the DG428DN consume?
The DG428DN has a specified low power consumption of 0.3 mW. According to the Vishay datasheet, its address latches reduce control-interface overhead while retaining break-before-make channel selection. Actual board-level consumption depends on supply voltage, address levels, latched logic states, and the selected channel, so use the manufacturer electrical-characteristics tables when calculating overall system power for precision or portable instrumentation.
What should I check before using DG428DN with external test equipment?
Check the signal amplitude, source impedance, off-state isolation, switching time, and channel-break behavior before connecting external test equipment. The DG428DN specifies a maximum on-resistance of 100 ohms, 225 ns turn-on time, 300 ns turn-off time, and 75 dB isolation. According to the Vishay datasheet, the device also supports break-before-make operation, helping prevent two channels from overlapping during selection transitions.
Where can I buy DG428DN online?
Use the Request a Quote form on this page to request DG428DN availability, current commercial terms, and a suitable quantity. The form is the appropriate channel for exact-MPN sourcing and lead-time confirmation without relying on a static listing. When requesting a quote, specify the 20-pin PLCC package, desired quantity, acceptable date code condition, and whether the DG428DN-E3 suffix is acceptable for your assembly.
What is the price of DG428DN?
The current commercial price for DG428DN should be requested through the Request a Quote form on this page. The form supports exact-package and exact-MPN sourcing for the 20-pin PLCC device and lets the buyer specify quantity and delivery requirements. Static prices can vary with market conditions, quantity, condition, and date code, so a quote provides the appropriate terms for procurement.
What is the lead time for DG428DN?
The current lead time for DG428DN should be confirmed through the Request a Quote form on this page. Include the required quantity, approved date-code policy, target delivery date, and whether the DG428DN-E3 ordering option is permitted. This provides procurement with the complete assembly requirement and avoids assuming that generic distributor inventory corresponds to the exact 20-pin PLCC configuration.
Is DG428DN in stock?
DG428DN stock should be confirmed through the Request a Quote form on this page because availability can change with quantity and date-code requirements. State the exact 20-pin PLCC package and required quantity in the request. If the DG428DN-E3 finish is acceptable, identify that explicitly, but retain DG428DN as the primary requested MPN when the approved BOM specifies it.
What can replace the DG428DN in a pin-compatible design?
The documented pin-compatible candidate is the Vishay DG428DN-E3, which is also listed as a 20-pin PLCC multiplexer. The ADG428BPZ offers a similar 8:1 function and comparable 100-ohm maximum on-resistance, but its different package prevents direct PCB substitution. Before approving DG428DN-E3 as a replacement, verify its complete pinout, electrical characteristics, operating-temperature range, lifecycle status, and procurement documentation.

엔지니어링 참조 데이터: DG428DN — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the DG428DN when a design needs eight single-ended or four differential analog channels, latched address control, and a 20-pin PLCC footprint. Its 100-ohm maximum on-resistance, 75 dB isolation, and break-before-make behavior suit acquisition, test, process-control, avionics, and instrumentation systems that route several signals through a shared front end. Select DG428DN-E3 when that ordering suffix is approved for its finish, qualification, or purchasing requirements, after checking the manufacturer ordering information. The ADG428BPZ may be considered when a redesign is acceptable because it offers a similar 8:1 function and comparable 100-ohm maximum on-resistance, but its different package prevents PCB drop-in use. For designs needing lower on-resistance, faster transitions, or a different channel count, review other multiplexers rather than forcing the DG428DN into a performance target it was not specified to meet.

대체품과의 비교

파라미터 이 제품 DG428DN-E3
Brand Vishay Intertechnology Vishay Intertechnology
Package 20-pin PLCC (9 x 9 mm) 20-pin PLCC (9 x 9 mm)
Configuration 8:1 single-ended or 4:1 differential 8:1 single-ended or 4:1 differential
Number of Switches 8 8
On-Resistance 100 ohms maximum 100 ohms maximum
Supply Voltage Range -15 V to +15 V -15 V to +15 V
Turn-On Time 225 ns 225 ns
Turn-Off Time 300 ns 300 ns
Isolation 75 dB 75 dB
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C
Address Latches Onboard, TTL-compatible Onboard, TTL-compatible
Switching Sequence Break-before-make Break-before-make

주요 차별점

  • Supports both single-ended and differential routing in one device (vs ADG428BPZ)
  • Onboard latches reduce processor interface overhead (vs ADG428BPZ)
  • Break-before-make switching protects channel isolation (vs ADG428BPZ)
  • Documented 100-ohm maximum on-resistance (vs DG428DN-E3)

설계 노트

Do not treat the ADG428BPZ as a board-level drop-in replacement for the DG428DN. Although both provide an 8:1 multiplexing function and comparable 100-ohm maximum on-resistance, the DG428DN uses a 20-pin PLCC package while the ADG428BPZ uses a different package. Confirm the complete pin map, supply arrangement, control logic, and electrical limits in the manufacturer datasheet before approving a substitution or starting a PCB layout.

Route each analog channel and the common output as short and direct as practical, with a continuous ground plane beneath the PLCC footprint where the package and application permit. Keep digital address and latch traces away from sensitive analog inputs to reduce capacitive coupling. Because the specified maximum on-resistance is 100 ohms, include switch resistance and source impedance in the settling-time and gain-error budget, particularly for high-impedance sensors.

Use the break-before-make behavior as part of the system timing design. Allow the turn-off interval of 300 ns before expecting a newly selected channel to begin its 225 ns turn-on interval, and add amplifier or converter acquisition time afterward. For external test equipment, use controlled impedance paths and verify that transient interaction during channel changes remains acceptable to the equipment under test.

Design the dual-supply rails with the correct polarity and keep their magnitude within the -15 V to +15 V operating range; the 44 V value is an absolute maximum rating, not a recommended operating condition. Decouple the supply pins locally, provide a stable analog return, and check startup behavior for signals that may remain connected while the address latch or enable state is undefined.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The DG428DN-E3 ordering suffix may relate to a lead-free finish, but no exact compliance declaration for DG428DN was found. Environmental qualification for automotive use must be confirmed for the selected orderable suffix.

데이터 검증일: 2026-11-10 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

DG428DN datasheet DG428DN pinout DG428DN datasheet pdf DG428DN specifications DG428DN PLCC-20 DG428DN equivalent DG428DN replacement DG428DN cross reference DG428DN vs ADG428BPZ DG428DN price DG428DN stock Vishay DG428DN DG428DN 8:1 analog mux DG428DN data acquisition DG428DN automatic test equipment

관련 부품 & 용어

Vishay Intertechnology DG428DN DG428DN-E3 ADG428BPZ analog multiplexer multiplexer switch IC analog switch interface IC 8:1 multiplexer 4:1 differential multiplexer latchable address interface TTL-compatible latch break-before-make switching on-resistance charge injection isolation turn-on time turn-off time PLCC-20 surface-mount package data acquisition automatic test equipment process control avionics instrumentation precision instrumentation
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기