Texas Instruments

DS90C363AMTDX - 18-Bit 65MHz LVDS Transmitter | TI

料号: DS90C363AMTDX ✗ 停产
3 V to 3.6 V Vdss 48-TSSOP, 0.240 inch width by 6.10 mm length Package 65 MHz Speed
最小起订量: 1 |

DS90C363AMTDX 概述

Texas Instruments DS90C363AMTDX is a 3.3 V programmable LVDS flat-panel display link transmitter with 18 data bits, a 65 MHz maximum pixel clock, three LVDS drivers, and 21 differential inputs in a 48-pin TSSOP package. It converts parallel display data into low-voltage differential-signaling lanes for reliable transfer between a graphics source and an external display panel.

An LVDS FPD-Link transmitter is an interface IC within the broader signal-chain hierarchy of display controller, interface transceiver, semiconductor, and electronic system. FPD-Link carries wide parallel data over fewer differential pairs by transmitting balanced logic signals across twisted-pair cables or controlled-impedance PCB traces. This approach reduces signal count while supporting reliable communication over a compact display interface.

The DS90C363AMTDX provides a programmable 18-bit flat-panel link, a 65 MHz operating limit, and a 3 V to 3.6 V supply range. Its three LVDS outputs support multiple data lanes, while 21 inputs accommodate the parallel data, control, clock, and configuration functions required by an FPD-Link transmitter. Differential signaling improves noise immunity compared with single-ended transmission in display environments where pixel-clock edges must remain clean.

The transmitter architecture uses parallel-to-serial conversion and low-voltage differential outputs to support panel data transfer. Programming controls permit adaptation to supported display timing and link configurations, while the 65 MHz clock ceiling defines the usable data-transfer envelope. Designers must observe the manufacturer’s input, output, timing, and power-sequencing requirements to preserve signal integrity from the source device through the cable or PCB connection to the receiver and panel interface.

Typical applications include LCD monitor and flat-panel display controllers, industrial human-machine interfaces, automotive display systems, digital signage, and embedded graphics platforms. The device is particularly relevant when a design requires an 18-bit FPD-Link transmitter rather than a general-purpose parallel-to-LVDS serializer. Its dedicated display functions simplify source-side implementation when the receiving panel expects compatible FPD-Link signaling.

PCB implementation should keep the transmitter close to the graphics engine, use controlled-impedance differential routing, and provide the decoupling and layout specified by the TI DS90C363 manufacturer datasheet. Cable and connector selection also matters because skew and loss can degrade the differential signal at higher pixel-clock rates. The 48-TSSOP footprint supports conventional surface-mount assembly but requires careful fanout from the source component to the LVDS connector.

This product page combines the exact orderable MPN, manufacturer specifications, package details, sourcing information, interface application guidance, and design considerations. It also distinguishes the target from documented same-family alternatives and identifies where an engineer must confirm revision-specific behavior before approving a direct substitution.

直接替换替代料: DS90C363AMTDX ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: DS90C363AMTDX (相同外形与封装尺寸) ——差异在于 Package, Product Type, RoHS Status, Supply Voltage.

Texas Instruments
Package: 48-pin TSSOP
Product Type: Programmable LVDS FPD-Link transmitter
RoHS Status: Non-compliant
对比 DS90C363AMTDX →
Texas Instruments
Package: 48-TSSOP (MTD)
RoHS Status: Compliant
Supply Voltage: 3.3 V (typ.)
对比 DS90C363AMTDX →

DS90C363BMTX

✅ 直接替换
Texas Instruments
📦 48-TSSOP
LVDS Transmitter (FPD-Link Serializer) · 3.3 V (typ.) · 18-bit parallel RGB · 65 MHz · Up to 1.3 Gbps · Up to 170 Megabytes/sec · 345 mV (typ.) · 4 data + 1 clock

联系询价

查看数据手册 →

DS90C363AMTD

✅ 直接替换
Texas Instruments
📦 48-TSSOP
Programmable LVDS FPD-Link transmitter · 3 V to 3.6 V · 3.3 V · 18 bits · 65 MHz · 612.5 Mbps · 3 · 3/21

联系询价

查看数据手册 →

DS90CF363A

✅ 直接替换
📦 48-TSSOP
Related FPD-Link transmitter retains the 65 MHz, 18-bit rating, but configuration, enable, and power-sequencing differences must be checked before substitution

📋 参考替代料(不在目录中)

DS90C363AMTDX 规格参数

Product Type 18-bit programmable LVDS FPD-Link transmitter
Supply Voltage Range 3 V to 3.6 V
最大时钟频率 65 MHz
Number of LVDS Drivers 3 drivers
Number of Receivers or Inputs 21 inputs
Parallel Data Width 18 bits
接口类型 LVDS FPD-Link
封装 48-TSSOP, 0.240 inch width by 6.10 mm length
Packaging Tape and reel
安装类型 Surface mount
Logic Voltage 3.3 V
Data Transmission Type LVDS data transmission
Product Family DS90C363 / DS90CF363A

DS90C363AMTDX 48-tssop, 0.240 inch width by 6.10 mm length 引脚配置指南

DS90C363AMTDX(48-tssop, 0.240 inch width by 6.10 mm length 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

DS90C363AMTDX 的 48-tssop, 0.240 inch width by 6.10 mm length 封装引脚图

暂无详细引脚数据: DS90C363AMTDX.

请参阅 数据手册 以查看完整引脚配置。

典型应用

DS90C363AMTDX 适用于 6 应用s: LCD Monitor Display Interface, Industrial Human-Machine Interface, Automotive Display Controller, Digital Signage Player, Embedded Graphics Platform, Point-of-Sale Display Terminal.

📺

LCD Monitor Display Interface

The DS90C363AMTDX fits the source side of a compatible 18-bit flat-panel display link because it converts parallel display data into three differential LVDS lanes at up to 65 MHz. The 3.3 V supply range and 48-pin TSSOP package align with conventional graphics-controller PCB architecture. Place the transmitter near the graphics engine and LVDS connector, then route each differential pair with matched impedance and controlled spacing. Verify the panel receiver’s lane count, timing window, connector mapping, and initialization sequence before production release.

🏭

Industrial Human-Machine Interface

The DS90C363AMTDX is suitable for industrial HMIs that distribute 18-bit display data from an embedded controller to a remote panel over differential LVDS links. Its 65 MHz clock capability supports the documented operating envelope, while three LVDS drivers can serve compatible multi-lane panel links. Industrial implementations should reserve differential-pair routing space, maintain a continuous ground reference, and isolate noisy power and switching circuitry from the display path. Confirm industrial temperature requirements and panel-specific initialization before selecting the exact orderable suffix.

🚗

Automotive Display Controller

The DS90C363AMTDX can serve as the LVDS transmitter in an automotive display system that uses a compatible 18-bit FPD-Link architecture. Its 3.3 V operation, 65 MHz pixel-clock limit, and three differential outputs are central to the source-side interface. Automotive deployment requires confirmation of temperature grade, functional-safety expectations, radiation and ESD design practices, and panel qualification. Use differential routing with controlled impedance, minimize connector transitions, and validate the complete cable or PCB channel against the receiver’s eye and timing requirements.

📱

Digital Signage Player

The DS90C363AMTDX fits digital-signage designs that use a compatible 18-bit panel link from a media processor or embedded graphics controller. The dedicated FPD-Link transmitter avoids using a generic serializer for a display-oriented interface, supporting a maximum 65 MHz clock and three LVDS outputs. In multi-display installations, each panel may impose different timing and initialization requirements, so configure and validate every channel separately. Keep the transmitter and connector region free of high-current switching paths, and provide local supply decoupling according to the manufacturer layout guidance.

🖥️

Embedded Graphics Platform

The DS90C363AMTDX is appropriate for embedded graphics platforms that drive a receiver-compatible 18-bit flat-panel display at up to 65 MHz. Its three LVDS outputs and 21 inputs provide the parallel control, data, clock, and configuration paths required by a dedicated display transmitter. This arrangement simplifies the source hardware compared with implementing LVDS encoding in an FPGA, although FPGA logic may still control panel timing and initialization. Route the transmitter outputs directly toward the connector or receiver, maintain matched pair lengths, and check source, receiver, and cable timing together.

🖥️

Point-of-Sale Display Terminal

The DS90C363AMTDX can support point-of-sale terminals with a compatible 18-bit FPD-Link display architecture, providing a focused alternative to a general-purpose parallel interface. The 65 MHz operating limit covers the device’s stated display-clock envelope, while differential outputs improve robustness in retail terminals containing switching power supplies, display backlights, and noisy peripherals. Place the device close to the graphics source, keep supply return paths compact, and separate LVDS traces from backlight and power-converter routing. Confirm connector mapping, cable length, panel receiver capability, and startup timing before production.

What is DS90C363AMTDX?
The DS90C363AMTDX is a 3.3 V, 18-bit programmable LVDS transmitter designed for flat-panel display links operating to 65 MHz. According to the TI DS90C363 manufacturer datasheet, it combines three LVDS drivers with 21 inputs in a 48-pin TSSOP package. The device converts parallel display data into differential FPD-Link signals for an external display receiver or panel interface.
What are the key specifications of DS90C363AMTDX that engineers should know?
The key DS90C363AMTDX specifications are an 18-bit data interface, 65 MHz maximum clock frequency, 3 V to 3.6 V supply range, three LVDS drivers, and a 48-pin TSSOP package. The TI product page identifies the device as a programmable 3.3 V LVDS transmitter for 18-bit flat-panel display links. These parameters define its display timing range, supply requirements, channel count, and PCB footprint.
Where can I download the DS90C363AMTDX datasheet PDF?
The DS90C363AMTDX technical documentation is available from the official TI DS90C363 product page at https://www.ti.com/product/DS90C363. Select the datasheet link on that page to obtain the manufacturer document covering the DS90C363A and DS90CF363A devices. Use its pin-description table, timing diagrams, and electrical characteristics when assigning PCB pins or validating display-link operation.
Where can I find the DS90C363AMTDX pinout?
The DS90C363AMTDX pinout is published in the pin-configuration section of the TI DS90C363 manufacturer datasheet. The exact orderable device uses a 48-pin TSSOP package, so all 48 terminals must be mapped before layout release. Use the manufacturer’s data and power pins, ground assignments, LVDS outputs, clock inputs, and configuration pins rather than assigning connections from a generic LVDS serializer diagram.
How does DS90C363AMTDX compare with DS90C363B?
The DS90C363B is identified as an alternative to the DS90C363 family and may fit the same display-interface design when its revision-specific electrical data confirms compatibility. The TI support discussion specifically mentions the DS90C363B as an alternative to the NRND DS90C363MTD. Before replacing DS90C363AMTDX, compare the complete pin table, timing, register behavior, power requirements, and LVDS output specifications.
Is DS90C363AMTDX suitable for an LCD monitor controller?
Yes, the DS90C363AMTDX is suitable for a compatible 18-bit FPD-Link display architecture. Its 65 MHz maximum clock, programmable transmitter configuration, three LVDS outputs, and 3.3 V operation align with source-side LCD controller designs using a compatible receiver. Confirm the target panel’s lane count, input mapping, timing range, connector topology, and initialization requirements before committing the design.
When should I choose DS90C363AMTDX over DS90C363A?
Choose DS90C363AMTDX when the production BOM requires the tape-and-reel 48-TSSOP orderable designation and its documented operating configuration matches the display design. The base-family designation DS90C363A identifies the underlying device family but does not by itself establish the exact orderable suffix, temperature grade, or packing arrangement. Verify those ordering fields against the manufacturer ordering information before treating the two labels as interchangeable.
What can replace DS90C363AMTDX?
The documented replacement path for the DS90C363 family includes the DS90C363B, but it is not safe to install it without checking revision-specific behavior. TI support discussion identifies DS90C363B as an alternative to DS90C363MTD. For a DS90C363AMTDX PCB, confirm the 48-pin pinout, 3.3 V supply compatibility, 65 MHz timing limit, LVDS electrical characteristics, configuration registers, and panel initialization sequence.
Is DS90C363AMTDX the same as DS90CF563MTD?
The DS90C363AMTDX and DS90CF563MTD are not automatically interchangeable merely because both are related display-interface devices. The DS90C363AMTDX is an 18-bit, 65 MHz FPD-Link transmitter with three LVDS drivers, while exact functions of the DS90CF563MTD require separate manufacturer documentation. Compare lane count, pixel-clock range, pinout, supply, protocol, and panel support before considering a replacement.
Where can I buy DS90C363AMTDX and check its lead time?
Use the Request a Quote form on this XAIPART page to request DS90C363AMTDX availability, current lead time, and minimum order quantity. The exact MPN is offered in a 48-pin TSSOP tape-and-reel configuration. Providing the target quantity and required delivery date allows the quote request to be matched to the appropriate supply channel without relying on stale catalog availability.
What is the price of DS90C363AMTDX?
Current DS90C363AMTDX pricing is handled through the Request a Quote form on this XAIPART page. The submitted quantity, delivery schedule, and exact orderable suffix determine the customer quote. This avoids publishing a static price that may not match the requested volume, packaging, or supply conditions. Use the form for both single-piece engineering evaluation and scheduled production demand.
Is DS90C363AMTDX in stock?
Use the Request a Quote form on this page for the current DS90C363AMTDX stock position and lead time. Availability can vary with quantity, date, and the exact 48-TSSOP tape-and-reel orderable suffix. A successful quote request confirms the current fulfillment path for the requested quantity and delivery window instead of relying on an unverified inventory statement.
What is the best Texas Instruments equivalent for DS90C363AMTDX?
The best documented Texas Instruments family candidate is the DS90C363B, which TI support materials identify as an alternative to the earlier DS90C363MTD. Whether it is a direct drop-in for DS90C363AMTDX depends on the package pinout, timing, configuration registers, LVDS output characteristics, and operating requirements. Validate those items in the current manufacturer datasheets before schematic or PCB release.
Can DS90C363AMTDX drive a 65MHz display interface?
The DS90C363AMTDX has a stated 65 MHz maximum operating frequency for its 18-bit flat-panel display link. The implementation must also satisfy the panel receiver’s lane timing, connector, cable, and signal-integrity requirements. At or near the upper clock limit, verify source and receiver tolerances, differential pair geometry, connector loss, and grounding using the application guidance in the manufacturer documentation.
What power and layout considerations apply to DS90C363AMTDX?
The DS90C363AMTDX operates from a 3 V to 3.6 V supply and requires careful high-speed layout around its 48-pin TSSOP footprint. Follow the TI DS90C363 manufacturer datasheet for decoupling, grounding, and LVDS routing. Keep the differential pairs short, matched, and controlled in impedance, minimize stubs and vias, and separate LVDS routing from noisy switching paths to preserve signal integrity.

工程参考数据: DS90C363AMTDX ——对比、设计指导和合规信息。

选型指南

Choose DS90C363AMTDX when the design requires the exact 48-TSSOP tape-and-reel orderable device for a compatible 18-bit, 65 MHz FPD-Link transmitter. Its three LVDS drivers and 21 inputs make it appropriate for panel-facing source electronics, provided the receiver, connector, and panel support the same signaling and timing. Consider DS90C363B when an updated family revision is permitted and its current pin, register, timing, and electrical characteristics pass a complete substitution review. DS90C363A represents the underlying family designation but should be selected only after its ordering suffix, grade, and packing are confirmed. DS90CF363A is a related transmitter whose shared 65 MHz, 18-bit architecture makes it worth evaluating, but enable, power-sequencing, and configuration differences may require software or schematic changes. For any alternative, validate the complete channel rather than relying on package appearance alone.

与替代料对比

参数 本产品 DS90C363B DS90C363A DS90CF363A
Package 48-TSSOP 48-TSSOP 48-TSSOP 48-TSSOP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Interface Protocol 18-bit flat-panel display FPD-Link with LVDS DS90C363 family FPD-Link 18-bit flat-panel display FPD-Link with LVDS 18-bit flat-panel display FPD-Link with LVDS

关键差异点

  • Dedicated 18-bit display transmitter rather than a general-purpose serializer (对比 DS90CF563MTD)
  • Documented higher-bandwidth family alternative (对比 DS90C363A)
  • Three-lane differential output for compatible multi-lane FPD-Link panels (对比 DS90C363B)

设计说明

Route each LVDS differential pair as a controlled-impedance pair with uniform spacing and matched length characteristics. Keep the transmitter close to the graphics controller or FPD-Link connector, minimize vias and stubs, and avoid routing beneath noisy switching-regulator nodes. The 65 MHz clock limit makes receiver timing, connector loss, and pair skew part of the end-to-end channel design rather than isolated PCB concerns.

Use a clean 3.3 V supply within the documented 3 V to 3.6 V range. Place the required bypass capacitors at the power and ground pins using the exact values and topology shown in the TI DS90C363 manufacturer datasheet. Keep high-current return paths separate from the transmitter ground and sensitive interface area, because power-supply noise or ground bounce can degrade LVDS timing margins.

Do not treat the DS90C363 family label, revision letter, or packaging suffix as proof of automatic interchangeability. Before replacing DS90C363AMTDX, compare all 48 pins, supply sequencing, enable behavior, configuration registers, timing limits, and LVDS output specifications. A 48-TSSOP footprint alone is insufficient because a package-compatible device can still require different initialization or have different lane timing.

Validate the complete source-to-panel path, including transmitter outputs, connector transitions, cable or PCB channel, receiver inputs, and grounding. At clock rates near 65 MHz, use receiver timing information and system measurements to assess eye margin rather than relying only on schematic connectivity. Avoid adding test pads, long breakout stubs, or unterminated branches directly on sensitive differential pairs.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status were not stated in the cited technical or distributor records. The related DS90C363MTD is described as NRND in TI support discussion.

相关搜索

DS90C363AMTDX datasheet DS90C363AMTDX pinout DS90C363AMTDX datasheet pdf DS90C363AMTDX specifications DS90C363AMTDX 48-TSSOP DS90C363AMTDX equivalent DS90C363AMTDX replacement DS90C363AMTDX vs DS90C363B DS90C363AMTDX FPD-Link transmitter DS90C363AMTDX price DS90C363AMTDX stock Texas Instruments DS90C363AMTDX DS90C363AMTDX schematic DS90C363 65MHz LVDS transmitter

相关元器件 & 术语

Texas Instruments DS90C363AMTDX DS90C363A DS90C363B DS90CF363A DS90C363MTD DS90CF563MTD LVDS FPD-Link flat-panel display link programmable transmitter interface transceiver parallel-to-serial converter differential signaling semiconductor 48-TSSOP TSSOP package surface-mount package 65 MHz pixel clock 18-bit data interface three LVDS drivers digital signage industrial human-machine interface automotive display RoHS REACH AEC-Q100
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情