DS90C363AMTDX - 18-Bit 65MHz LVDS Transmitter | TI
MPN: DS90C363AMTDX ✗ انتهى عمره الإنتاجيDS90C363AMTDX نظرة عامة
An LVDS FPD-Link transmitter is an interface IC within the broader signal-chain hierarchy of display controller, interface transceiver, semiconductor, and electronic system. FPD-Link carries wide parallel data over fewer differential pairs by transmitting balanced logic signals across twisted-pair cables or controlled-impedance PCB traces. This approach reduces signal count while supporting reliable communication over a compact display interface.
The DS90C363AMTDX provides a programmable 18-bit flat-panel link, a 65 MHz operating limit, and a 3 V to 3.6 V supply range. Its three LVDS outputs support multiple data lanes, while 21 inputs accommodate the parallel data, control, clock, and configuration functions required by an FPD-Link transmitter. Differential signaling improves noise immunity compared with single-ended transmission in display environments where pixel-clock edges must remain clean.
The transmitter architecture uses parallel-to-serial conversion and low-voltage differential outputs to support panel data transfer. Programming controls permit adaptation to supported display timing and link configurations, while the 65 MHz clock ceiling defines the usable data-transfer envelope. Designers must observe the manufacturer’s input, output, timing, and power-sequencing requirements to preserve signal integrity from the source device through the cable or PCB connection to the receiver and panel interface.
Typical applications include LCD monitor and flat-panel display controllers, industrial human-machine interfaces, automotive display systems, digital signage, and embedded graphics platforms. The device is particularly relevant when a design requires an 18-bit FPD-Link transmitter rather than a general-purpose parallel-to-LVDS serializer. Its dedicated display functions simplify source-side implementation when the receiving panel expects compatible FPD-Link signaling.
PCB implementation should keep the transmitter close to the graphics engine, use controlled-impedance differential routing, and provide the decoupling and layout specified by the TI DS90C363 manufacturer datasheet. Cable and connector selection also matters because skew and loss can degrade the differential signal at higher pixel-clock rates. The 48-TSSOP footprint supports conventional surface-mount assembly but requires careful fanout from the source component to the LVDS connector.
This product page combines the exact orderable MPN, manufacturer specifications, package details, sourcing information, interface application guidance, and design considerations. It also distinguishes the target from documented same-family alternatives and identifies where an engineer must confirm revision-specific behavior before approving a direct substitution.
بدائل مباشرة لـ DS90C363AMTDX — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع DS90C363AMTDX (نفس عامل الشكل والبصمة) — يختلف في Package, Product Type, RoHS Status, Supply Voltage.
DS90C363BMTX
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DS90C363AMTD
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DS90CF363A
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90C363AMTDX المواصفات
| Product Type | 18-bit programmable LVDS FPD-Link transmitter |
| Supply Voltage Range | 3 V to 3.6 V |
| أقصى تردد للساعة | 65 MHz |
| Number of LVDS Drivers | 3 drivers |
| Number of Receivers or Inputs | 21 inputs |
| Parallel Data Width | 18 bits |
| نوع الواجهة | LVDS FPD-Link |
| العلبة | 48-TSSOP, 0.240 inch width by 6.10 mm length |
| Packaging | Tape and reel |
| نوع التركيب | Surface mount |
| Logic Voltage | 3.3 V |
| Data Transmission Type | LVDS data transmission |
| Product Family | DS90C363 / DS90CF363A |
دليل تكوين أطراف DS90C363AMTDX 48-tssop, 0.240 inch width by 6.10 mm length
تكوين الأطراف لـ DS90C363AMTDX (حزمة 48-tssop, 0.240 inch width by 6.10 mm length). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ DS90C363AMTDX.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
DS90C363AMTDX مناسب لـ 6 التطبيقs: LCD Monitor Display Interface, Industrial Human-Machine Interface, Automotive Display Controller, Digital Signage Player, Embedded Graphics Platform, Point-of-Sale Display Terminal.
LCD Monitor Display Interface
The DS90C363AMTDX fits the source side of a compatible 18-bit flat-panel display link because it converts parallel display data into three differential LVDS lanes at up to 65 MHz. The 3.3 V supply range and 48-pin TSSOP package align with conventional graphics-controller PCB architecture. Place the transmitter near the graphics engine and LVDS connector, then route each differential pair with matched impedance and controlled spacing. Verify the panel receiver’s lane count, timing window, connector mapping, and initialization sequence before production release.
موصى به
Industrial Human-Machine Interface
The DS90C363AMTDX is suitable for industrial HMIs that distribute 18-bit display data from an embedded controller to a remote panel over differential LVDS links. Its 65 MHz clock capability supports the documented operating envelope, while three LVDS drivers can serve compatible multi-lane panel links. Industrial implementations should reserve differential-pair routing space, maintain a continuous ground reference, and isolate noisy power and switching circuitry from the display path. Confirm industrial temperature requirements and panel-specific initialization before selecting the exact orderable suffix.
موصى به
Automotive Display Controller
The DS90C363AMTDX can serve as the LVDS transmitter in an automotive display system that uses a compatible 18-bit FPD-Link architecture. Its 3.3 V operation, 65 MHz pixel-clock limit, and three differential outputs are central to the source-side interface. Automotive deployment requires confirmation of temperature grade, functional-safety expectations, radiation and ESD design practices, and panel qualification. Use differential routing with controlled impedance, minimize connector transitions, and validate the complete cable or PCB channel against the receiver’s eye and timing requirements.
موصى به
Digital Signage Player
The DS90C363AMTDX fits digital-signage designs that use a compatible 18-bit panel link from a media processor or embedded graphics controller. The dedicated FPD-Link transmitter avoids using a generic serializer for a display-oriented interface, supporting a maximum 65 MHz clock and three LVDS outputs. In multi-display installations, each panel may impose different timing and initialization requirements, so configure and validate every channel separately. Keep the transmitter and connector region free of high-current switching paths, and provide local supply decoupling according to the manufacturer layout guidance.
موصى به
Embedded Graphics Platform
The DS90C363AMTDX is appropriate for embedded graphics platforms that drive a receiver-compatible 18-bit flat-panel display at up to 65 MHz. Its three LVDS outputs and 21 inputs provide the parallel control, data, clock, and configuration paths required by a dedicated display transmitter. This arrangement simplifies the source hardware compared with implementing LVDS encoding in an FPGA, although FPGA logic may still control panel timing and initialization. Route the transmitter outputs directly toward the connector or receiver, maintain matched pair lengths, and check source, receiver, and cable timing together.
موصى به
Point-of-Sale Display Terminal
The DS90C363AMTDX can support point-of-sale terminals with a compatible 18-bit FPD-Link display architecture, providing a focused alternative to a general-purpose parallel interface. The 65 MHz operating limit covers the device’s stated display-clock envelope, while differential outputs improve robustness in retail terminals containing switching power supplies, display backlights, and noisy peripherals. Place the device close to the graphics source, keep supply return paths compact, and separate LVDS traces from backlight and power-converter routing. Confirm connector mapping, cable length, panel receiver capability, and startup timing before production.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ DS90C363AMTDX — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | DS90C363B | DS90C363A | DS90CF363A |
|---|---|---|---|---|
| Package | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Interface Protocol | 18-bit flat-panel display FPD-Link with LVDS | DS90C363 family FPD-Link | 18-bit flat-panel display FPD-Link with LVDS | 18-bit flat-panel display FPD-Link with LVDS |
أبرز الفروقات
- Dedicated 18-bit display transmitter rather than a general-purpose serializer (مقابلDS90CF563MTD)
- Documented higher-bandwidth family alternative (مقابلDS90C363A)
- Three-lane differential output for compatible multi-lane FPD-Link panels (مقابلDS90C363B)
ملاحظات التصميم
Route each LVDS differential pair as a controlled-impedance pair with uniform spacing and matched length characteristics. Keep the transmitter close to the graphics controller or FPD-Link connector, minimize vias and stubs, and avoid routing beneath noisy switching-regulator nodes. The 65 MHz clock limit makes receiver timing, connector loss, and pair skew part of the end-to-end channel design rather than isolated PCB concerns.
Use a clean 3.3 V supply within the documented 3 V to 3.6 V range. Place the required bypass capacitors at the power and ground pins using the exact values and topology shown in the TI DS90C363 manufacturer datasheet. Keep high-current return paths separate from the transmitter ground and sensitive interface area, because power-supply noise or ground bounce can degrade LVDS timing margins.
Do not treat the DS90C363 family label, revision letter, or packaging suffix as proof of automatic interchangeability. Before replacing DS90C363AMTDX, compare all 48 pins, supply sequencing, enable behavior, configuration registers, timing limits, and LVDS output specifications. A 48-TSSOP footprint alone is insufficient because a package-compatible device can still require different initialization or have different lane timing.
Validate the complete source-to-panel path, including transmitter outputs, connector transitions, cable or PCB channel, receiver inputs, and grounding. At clock rates near 65 MHz, use receiver timing information and system measurements to assess eye margin rather than relying only on schematic connectivity. Avoid adding test pads, long breakout stubs, or unterminated branches directly on sensitive differential pairs.
معلومات الامتثال
RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status were not stated in the cited technical or distributor records. The related DS90C363MTD is described as NRND in TI support discussion.