Texas Instruments

DS90CR288MTDX - 28-Bit 75MHz LVDS Receiver | Texas Instruments

料号: DS90CR288MTDX ✓ 量产中
3.3 V Vdss 56-TSSOP Package 75 MHz Speed
最小起订量: 1 |

DS90CR288MTDX 概述

Texas Instruments DS90CR288MTDX is a 28-bit Channel Link LVDS receiver operating from a 3.3 V supply at up to 75 MHz, with a rising-edge data-strobe interface and a 56-TSSOP package. It is designed for high-speed point-to-point links that require a wide data path, differential signaling, and a separate strobe signal for source-synchronous data capture.

An LVDS receiver is an interface IC that converts low-voltage differential signaling into a digital logic signal suitable for processing by another device. LVDS belongs to the differential interface hierarchy and provides a way to transfer high-speed data while reducing sensitivity to noise and voltage offsets. The DS90CR288 combines a 28-bit parallel data interface with a 75 MHz Channel Link receiver, placing it in the broader category of interface ICs used for communication links.

Key features include 28 received data bits, a 75 MHz operating frequency, 3.3 V operation, rising-edge data strobing, and a 56-TSSOP package. The wide parallel data path reduces the number of serial links needed when transferring multi-bit information. The separate clock or data strobe provides a timing reference that can be phase-adjusted in the system, while differential reception helps preserve signal integrity across longer printed-circuit-board connections.

The DS90CR288 belongs to the Channel Link family of balanced digital-interface devices. Its receiver architecture is intended for point-to-point interconnections rather than multidrop buses, and its interface is designed around source-synchronous timing. System performance depends on maintaining controlled differential impedance, providing adequate input termination, and routing the data and strobe signals so that timing margin is preserved at the receiving device.

Typical uses include industrial control and instrumentation, digital video transport, test and measurement equipment, communications modules, and embedded systems that transfer a 28-bit word at 75 MHz. In each case, the receiver can provide a parallel data path to an FPGA, ASIC, microcontroller, or data converter without requiring a separate narrow serial receiver for every bit.

Layout should keep the differential clock and data pairs routed as controlled-impedance nets, with pair geometry maintained consistently from transmitter to receiver. Place termination components close to the receiver inputs and avoid stubs or unnecessary layer changes. The system designer should also verify receiver input thresholds, setup and hold timing, and the relationship between the data-strobe phase and the destination device capture clock.

This product page combines the manufacturer-defined receiver identity, package information, comparison details, and practical interface-design guidance. It is intended to help engineers locate the correct pin-compatible family options and plan the PCB, timing, signal-integrity, and sourcing steps needed to deploy the DS90CR288MTDX successfully.

直接替换替代料: DS90CR288MTDX ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

DS90CR288AMTDX/NOPB

✅ 直接替换
📦 56-TSSOP
Same-family 28-bit LVDS receiver format; exact revision-specific timing and electrical differences require datasheet verification

📋 参考替代料(不在目录中)

DS90CR288MTDX 规格参数

Device Type 28-bit LVDS Channel Link receiver
电源电压 3.3 V
最大时钟频率 75 MHz
Data Width 28 bit
Data Strobe Edge Rising edge
Interface Standard LVDS
Signal Type Differential data and clock inputs
封装 56-TSSOP
引脚数量 56 pin
安装类型 Surface mount
Number of Data Bits 28 bit
Clock or Data-Strobe Frequency 75 MHz
Operating Voltage 3.3 V
RoHS 状态 unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

DS90CR288MTDX 56-tssop 引脚配置指南

DS90CR288MTDX(56-tssop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

DS90CR288MTDX 的 56-tssop 封装引脚图

暂无详细引脚数据: DS90CR288MTDX.

请参阅 数据手册 以查看完整引脚配置。

典型应用

DS90CR288MTDX 适用于 6 应用s: Industrial Control Data Links, FPGA Digital Video Interface, Test and Measurement Instrumentation, Data Acquisition and Signal Processing, Communications and Network Modules, Embedded Imaging and Control Systems.

🏭

Industrial Control Data Links

The DS90CR288MTDX fits point-to-point industrial control links that need to transfer a 28-bit word at up to 75 MHz. Its differential LVDS receiver can connect a remote acquisition or motion-control section to a central FPGA or controller while reducing susceptibility to common-mode noise. The 3.3 V supply and rising-edge data-strobe interface support source-synchronous capture. Layout should preserve controlled-impedance routing for all data and timing pairs, and the receiving logic must be configured for the receiver's timing and output characteristics.

📺

FPGA Digital Video Interface

The DS90CR288MTDX can receive a 28-bit digital word and associated strobe from a video-processing chain before presenting it to an FPGA. Its 75 MHz Channel Link rate provides a wide parallel path for pixel, control, or packed test data, while LVDS signaling supports reliable transfer through a board-to-board or cable-based point-to-point connection. The FPGA capture logic should align its sampling clock to the received data strobe, and PCB routing should minimize skew between the 28 data bits and timing signal.

🔧

Test and Measurement Instrumentation

The DS90CR288MTDX is appropriate for high-speed test and measurement systems that move parallel measurement or pattern data from an acquisition board to a processing FPGA. The 28-bit interface reduces parallel routing compared with separate single-ended receivers, and the 75 MHz operating rate supports repeated acquisition and transfer cycles. Differential routing, receiver termination, and source-synchronous timing are central to preserving data integrity. The design should verify timing margin across connector or cable transitions and use consistent impedance-controlled routing between the transmitter and receiver.

📊

Data Acquisition and Signal Processing

The DS90CR288MTDX can serve as the receiving endpoint in a multi-channel data-acquisition system where converters or digitizers deliver a wide parallel payload through LVDS. Its 28-bit word width accommodates packed measurement results, while the 75 MHz data-strobe rate supports rapid transfer to an FPGA or digital processor. For reliable operation, every differential pair should maintain continuous impedance and controlled length, while the processor must use the strobe relationship and timing specifications to establish reliable word capture.

🌐

Communications and Network Modules

The DS90CR288MTDX is suitable for communications equipment that uses a point-to-point LVDS backplane or board-to-board link for parallel payload transfer. The 28-bit receiver reduces the number of physical signal pairs when the source already produces a parallel word, and differential operation improves noise tolerance compared with single-ended links. The implementation should reserve return-path and reference-plane continuity, apply the specified receiver termination, and confirm that connector or cable delays do not reduce the available timing margin at 75 MHz.

🧩

Embedded Imaging and Control Systems

The DS90CR288MTDX can connect imaging, motion-control, or machine-vision electronics to a high-speed embedded processing section. A 28-bit payload can carry packed image or control information, while the rising-edge strobe provides a dedicated source-synchronous timing reference up to 75 MHz. Differential pair routing and equal propagation delay are essential because data-to-strobe skew directly affects setup and hold margin. The receiving processor should be configured to capture the bus on the correct strobe edge and monitor for invalid or out-of-range link data.

推荐产品汇总

DS90CR285MTDX Related Channel Link transmitter 用于: Industrial Control Data Links, FPGA Digital Video Interface, Test and Measurement Instrumentation, Data Acquisition and Signal Processing, Communications and Network Modules, Embedded Imaging and Control Systems DS90CR288AMTDX/NOPB Same-family receiver comparison 用于: Industrial Control Data Links XC2C64A-5VQ100C AMD 用于: FPGA Digital Video Interface XC9572XL-7VQ64I AMD 用于: Test and Measurement Instrumentation DS90CF364AMTD Related LVDS receiver family comparison 用于: Data Acquisition and Signal Processing KSZ8041TLI-TR Microchip Technology 用于: Communications and Network Modules AT90CAN32-16AUR Microchip Technology 用于: Embedded Imaging and Control Systems
What is the DS90CR288MTDX?
The DS90CR288MTDX is a 28-bit LVDS Channel Link receiver designed for 3.3 V operation at up to 75 MHz. According to the manufacturer datasheet, it uses rising-edge data-strobe signaling and is packaged in a 56-TSSOP. Its principal function is to receive a differential 28-bit data channel and a differential clock or strobe, then present the recovered data to a downstream digital device.
Where can I download the DS90CR288MTDX datasheet PDF?
The official DS90CR288MTDX datasheet is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ds90cr288.pdf. The manufacturer datasheet is the controlling document for the receiver's electrical characteristics, timing diagrams, pin assignments, and recommended application circuit. Use its pin-description and timing tables when assigning PCB signals and setting up the source-synchronous interface.
Where can I find the DS90CR288MTDX pinout?
The DS90CR288MTDX pinout is defined in the pin-description table of the Texas Instruments manufacturer datasheet. The device uses a 56-TSSOP package, with 28 differential data inputs, a differential clock or strobe input, supply connections, and ground connections. Use the package drawing and pin table together to avoid confusing the clock input with the data-strobe connection.
What is the maximum frequency of the DS90CR288MTDX?
The DS90CR288MTDX supports a maximum clock frequency of 75 MHz. According to the Texas Instruments manufacturer datasheet, this is the operating frequency for the 28-bit Channel Link receiver. Timing margin must be evaluated using the complete system path, including transmitter skew, PCB propagation delay, receiver setup and hold requirements, and the phase relationship between the data and strobe.
Is the DS90CR288MTDX a receiver or a transmitter?
The DS90CR288MTDX is a receiver, not a transmitter. Its defining characteristics are a 28-bit receive channel, a 75 MHz differential clock or data-strobe interface, and a 3.3 V supply. According to the manufacturer datasheet, the device accepts LVDS data and timing signals and provides a parallel digital output for capture by an FPGA, ASIC, or other logic device.
Where can I buy DS90CR288MTDX online?
Use the Request a Quote form on this page to ask for DS90CR288MTDX availability, order quantity, and a current quotation. The part is identified as a Texas Instruments 56-TSSOP interface IC, and the exact ordering suffix DS90CR288MTDX should be included in the request. This avoids confusion with related Channel Link transmitters, other suffixes, or different package configurations.
What is the price of DS90CR288MTDX?
Submit the DS90CR288MTDX MPN through the Request a Quote form on this page for the current price and quantity schedule. Commercial pricing can change with market conditions, quantity, and supply status. Provide the required order quantity, target reel format, and manufacturing location so the supplier can confirm the exact DS90CR288MTDX configuration rather than a related device.
What is the lead time and stock status for DS90CR288MTDX?
Request the current lead time, minimum order quantity, and stock status for DS90CR288MTDX through the Request a Quote form on this page. The exact MPN is a 56-TSSOP, 3.3 V, 28-bit LVDS receiver operating to 75 MHz. Include your production schedule and reel requirements because availability for this ordering code should be confirmed for the requested quantity.
Is DS90CR288MTDX in stock?
Current stock status for DS90CR288MTDX should be confirmed through the Request a Quote form on this page. Use the complete manufacturer part number DS90CR288MTDX when requesting availability and include the required quantity and shipment date. The form can also clarify partial-lead fulfillment and standard packaging for this 56-TSSOP ordering code.
What is the best drop-in replacement for DS90CR288MTDX?
DS90CR288AMTDX/NOPB is the closest same-family candidate identified for comparison, but final replacement approval must confirm its pin assignments, timing, supply levels, and input termination against the DS90CR288MTDX manufacturer datasheets. The comparison candidate is also listed as a 56-TSSOP Channel Link receiver. No additional drop-in replacement could be established from the available cross-reference results.
Can DS90CR288AMTDX/NOPB replace DS90CR288MTDX?
DS90CR288AMTDX/NOPB may serve as a same-family replacement candidate, but it should not be approved solely from its name. Check the two manufacturer datasheets for identical 28-bit pin mapping, 3.3 V operation, 75 MHz timing, differential input requirements, and termination values. Also verify the ordering code, reel format, and any documented functional revision differences before treating it as a drop-in replacement.
When should I choose DS90CR288MTDX over another LVDS receiver?
Choose DS90CR288MTDX when the design specifically calls for a 28-bit, 75 MHz LVDS receiver in a 56-TSSOP package with a rising-edge data-strobe interface. Compare any candidate against the complete timing and pinout tables rather than relying only on package dimensions. The receiver is most appropriate for a point-to-point source-synchronous link where the destination device can capture the 28-bit word using the received strobe.
Is DS90CR288MTDX suitable for an FPGA data interface?
The DS90CR288MTDX is suitable for an FPGA interface when the board design uses a 28-bit LVDS link clocked at up to 75 MHz and the FPGA supports the corresponding LVDS input standard and source-synchronous capture method. Configure the receiver-to-FPGA timing to account for board skew and receiver latency, and use the manufacturer timing diagrams to establish setup and hold margin.
What is the difference between DS90CR288MTDX and DS90CR288AMTDX/NOPB?
DS90CR288MTDX and DS90CR288AMTDX/NOPB are closely related 28-bit Channel Link receiver candidates, but their functional and ordering differences must be confirmed from the manufacturer datasheets. The available comparison identifies both as 56-TSSOP family members and supports their use as a same-package comparison. Verify data timing, input thresholds, supply requirements, and ordering details before substituting one for the other.
What can replace DS90CR288MTDX?
The most defensible replacement candidate is DS90CR288AMTDX/NOPB, subject to a complete pin, timing, electrical, and package review. The candidate remains in the same Texas Instruments 28-bit LVDS receiver family and uses the same 56-TSSOP format. Because no independently verified second drop-in part was identified, engineers should avoid assuming that a transmitter or a receiver with a different data width is electrically interchangeable.

工程参考数据: DS90CR288MTDX ——对比、设计指导和合规信息。

选型指南

Choose the DS90CR288MTDX when the system specification requires a 3.3 V, 28-bit, 75 MHz LVDS receiver in a 56-TSSOP package with rising-edge data-strobe signaling. It is a strong fit for FPGA, instrumentation, industrial-control, and embedded imaging links that use point-to-point source-synchronous communication. Consider DS90CR288AMTDX/NOPB when it is listed in the approved component plan, but compare the manufacturer timing, pin, electrical, and ordering details before treating it as a drop-in replacement. Do not substitute DS90CR285MTDX when the receiver is required because it is a related Channel Link transmitter rather than the 28-bit receiver endpoint. Critical selection criteria are the 75 MHz timing margin, data-to-strobe skew, termination, differential routing, and compatibility with the downstream device's capture logic.

与替代料对比

参数 本产品 DS90CR288AMTDX/NOPB
Package 56-TSSOP 56-TSSOP
Brand Texas Instruments Texas Instruments
Device Function 28-bit LVDS receiver 28-bit Channel Link receiver
Data Width 28 bit 28 bit
Interface Type LVDS LVDS

关键差异点

  • Wide 28-bit parallel receive path (对比 DS90CR288AMTDX/NOPB)
  • High-speed differential clock or strobe capability (对比 DS90CR288AMTDX/NOPB)
  • Exact ordering-code identification (对比 DS90CR288AMTDX/NOPB)

设计说明

Route every differential data and clock pair as a coupled, impedance-controlled pair with continuous reference planes. Keep the 28 data bits and the data-strobe relationship within the skew budget of the receiving system. Avoid stubs, excessive vias, and layer transitions that interrupt the return path. If the connection crosses a connector, cable, or split plane, recalculate timing and loss over the complete path rather than relying only on the PCB section.

Place the receiver's differential termination network at the input pins and keep the stubs from the termination components as short as practical. Confirm the required termination value, common-mode range, and input thresholds against the manufacturer datasheet. At 75 MHz, component placement and interconnect geometry are part of the receiver interface; verify amplitude and timing at the device pins with suitable high-speed test methods.

Do not treat a 56-TSSOP package alone as proof of drop-in compatibility. Before substituting DS90CR288AMTDX/NOPB, compare all 28 data inputs, the clock or strobe, power, ground, and configuration pins, and then verify setup time, hold time, output timing, supply limits, and termination values. Also check the ordering suffix and reel format so the physical part delivered matches the production bill of materials.

Separate the LVDS receiver from noisy switching circuitry and provide a clean return path beneath the differential pairs. If the board also contains switching regulators or high-current digital paths, route those paths away from the receiver inputs and keep their return currents from crossing beneath the signal pairs. A solid ground reference and symmetric pair geometry are especially important when the link crosses multiple board layers.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the available product records.

数据核验日期: 2026-11-16 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

DS90CR288MTDX datasheet DS90CR288MTDX pinout DS90CR288MTDX datasheet pdf DS90CR288MTDX equivalent DS90CR288MTDX replacement DS90CR288MTDX cross reference DS90CR288MTDX 75MHz LVDS DS90CR288MTDX 56-TSSOP DS90CR288MTDX price DS90CR288MTDX stock Texas Instruments DS90CR288MTDX DS90CR288MTDX vs DS90CR288AMTDX/NOPB

相关元器件 & 术语

Texas Instruments DS90CR288MTDX DS90CR288AMTDX/NOPB DS90CR285MTDX DS90CF364AMTD Channel Link LVDS receiver differential line receiver interface IC digital interface source-synchronous interface data strobe rising-edge data strobe 28-bit parallel data 75 MHz 3.3 V power supply 56-TSSOP TSSOP package family surface-mount package FPGA industrial control test and measurement instrumentation video transport point-to-point link differential signal integrity
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情