DS90CR288MTDX - 28-Bit 75MHz LVDS Receiver | Texas Instruments
MPN: DS90CR288MTDX ✓ פעילDS90CR288MTDX סקירה
An LVDS receiver is an interface IC that converts low-voltage differential signaling into a digital logic signal suitable for processing by another device. LVDS belongs to the differential interface hierarchy and provides a way to transfer high-speed data while reducing sensitivity to noise and voltage offsets. The DS90CR288 combines a 28-bit parallel data interface with a 75 MHz Channel Link receiver, placing it in the broader category of interface ICs used for communication links.
Key features include 28 received data bits, a 75 MHz operating frequency, 3.3 V operation, rising-edge data strobing, and a 56-TSSOP package. The wide parallel data path reduces the number of serial links needed when transferring multi-bit information. The separate clock or data strobe provides a timing reference that can be phase-adjusted in the system, while differential reception helps preserve signal integrity across longer printed-circuit-board connections.
The DS90CR288 belongs to the Channel Link family of balanced digital-interface devices. Its receiver architecture is intended for point-to-point interconnections rather than multidrop buses, and its interface is designed around source-synchronous timing. System performance depends on maintaining controlled differential impedance, providing adequate input termination, and routing the data and strobe signals so that timing margin is preserved at the receiving device.
Typical uses include industrial control and instrumentation, digital video transport, test and measurement equipment, communications modules, and embedded systems that transfer a 28-bit word at 75 MHz. In each case, the receiver can provide a parallel data path to an FPGA, ASIC, microcontroller, or data converter without requiring a separate narrow serial receiver for every bit.
Layout should keep the differential clock and data pairs routed as controlled-impedance nets, with pair geometry maintained consistently from transmitter to receiver. Place termination components close to the receiver inputs and avoid stubs or unnecessary layer changes. The system designer should also verify receiver input thresholds, setup and hold timing, and the relationship between the data-strobe phase and the destination device capture clock.
This product page combines the manufacturer-defined receiver identity, package information, comparison details, and practical interface-design guidance. It is intended to help engineers locate the correct pin-compatible family options and plan the PCB, timing, signal-integrity, and sourcing steps needed to deploy the DS90CR288MTDX successfully.
חלופות תחליף ישיר עבור DS90CR288MTDX — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
DS90CR288AMTDX/NOPB
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DS90CR288MTDX מפרטים
| Device Type | 28-bit LVDS Channel Link receiver |
| מתח אספקה | 3.3 V |
| תדר שעון מקסימלי | 75 MHz |
| Data Width | 28 bit |
| Data Strobe Edge | Rising edge |
| Interface Standard | LVDS |
| Signal Type | Differential data and clock inputs |
| מארז | 56-TSSOP |
| מספר פינים | 56 pin |
| סוג הרכבה | Surface mount |
| Number of Data Bits | 28 bit |
| Clock or Data-Strobe Frequency | 75 MHz |
| Operating Voltage | 3.3 V |
| סטטוס RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
מדריך תצורת פינים של DS90CR288MTDX 56-tssop
תצורת פינים עבור DS90CR288MTDX (מארזת 56-tssop). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור DS90CR288MTDX.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
DS90CR288MTDX מתאים עבור 6 יישוםs: Industrial Control Data Links, FPGA Digital Video Interface, Test and Measurement Instrumentation, Data Acquisition and Signal Processing, Communications and Network Modules, Embedded Imaging and Control Systems.
Industrial Control Data Links
The DS90CR288MTDX fits point-to-point industrial control links that need to transfer a 28-bit word at up to 75 MHz. Its differential LVDS receiver can connect a remote acquisition or motion-control section to a central FPGA or controller while reducing susceptibility to common-mode noise. The 3.3 V supply and rising-edge data-strobe interface support source-synchronous capture. Layout should preserve controlled-impedance routing for all data and timing pairs, and the receiving logic must be configured for the receiver's timing and output characteristics.
מומלץ
FPGA Digital Video Interface
The DS90CR288MTDX can receive a 28-bit digital word and associated strobe from a video-processing chain before presenting it to an FPGA. Its 75 MHz Channel Link rate provides a wide parallel path for pixel, control, or packed test data, while LVDS signaling supports reliable transfer through a board-to-board or cable-based point-to-point connection. The FPGA capture logic should align its sampling clock to the received data strobe, and PCB routing should minimize skew between the 28 data bits and timing signal.
מומלץ
Test and Measurement Instrumentation
The DS90CR288MTDX is appropriate for high-speed test and measurement systems that move parallel measurement or pattern data from an acquisition board to a processing FPGA. The 28-bit interface reduces parallel routing compared with separate single-ended receivers, and the 75 MHz operating rate supports repeated acquisition and transfer cycles. Differential routing, receiver termination, and source-synchronous timing are central to preserving data integrity. The design should verify timing margin across connector or cable transitions and use consistent impedance-controlled routing between the transmitter and receiver.
מומלץ
Data Acquisition and Signal Processing
The DS90CR288MTDX can serve as the receiving endpoint in a multi-channel data-acquisition system where converters or digitizers deliver a wide parallel payload through LVDS. Its 28-bit word width accommodates packed measurement results, while the 75 MHz data-strobe rate supports rapid transfer to an FPGA or digital processor. For reliable operation, every differential pair should maintain continuous impedance and controlled length, while the processor must use the strobe relationship and timing specifications to establish reliable word capture.
מומלץ
Communications and Network Modules
The DS90CR288MTDX is suitable for communications equipment that uses a point-to-point LVDS backplane or board-to-board link for parallel payload transfer. The 28-bit receiver reduces the number of physical signal pairs when the source already produces a parallel word, and differential operation improves noise tolerance compared with single-ended links. The implementation should reserve return-path and reference-plane continuity, apply the specified receiver termination, and confirm that connector or cable delays do not reduce the available timing margin at 75 MHz.
מומלץ
Embedded Imaging and Control Systems
The DS90CR288MTDX can connect imaging, motion-control, or machine-vision electronics to a high-speed embedded processing section. A 28-bit payload can carry packed image or control information, while the rising-edge strobe provides a dedicated source-synchronous timing reference up to 75 MHz. Differential pair routing and equal propagation delay are essential because data-to-strobe skew directly affects setup and hold margin. The receiving processor should be configured to capture the bus on the correct strobe edge and monitor for invalid or out-of-range link data.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור DS90CR288MTDX — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DS90CR288AMTDX/NOPB |
|---|---|---|
| Package | 56-TSSOP | 56-TSSOP |
| Brand | Texas Instruments | Texas Instruments |
| Device Function | 28-bit LVDS receiver | 28-bit Channel Link receiver |
| Data Width | 28 bit | 28 bit |
| Interface Type | LVDS | LVDS |
מבדילים עיקריים
- Wide 28-bit parallel receive path (לעומתDS90CR288AMTDX/NOPB)
- High-speed differential clock or strobe capability (לעומתDS90CR288AMTDX/NOPB)
- Exact ordering-code identification (לעומתDS90CR288AMTDX/NOPB)
הערות תכנון
Route every differential data and clock pair as a coupled, impedance-controlled pair with continuous reference planes. Keep the 28 data bits and the data-strobe relationship within the skew budget of the receiving system. Avoid stubs, excessive vias, and layer transitions that interrupt the return path. If the connection crosses a connector, cable, or split plane, recalculate timing and loss over the complete path rather than relying only on the PCB section.
Place the receiver's differential termination network at the input pins and keep the stubs from the termination components as short as practical. Confirm the required termination value, common-mode range, and input thresholds against the manufacturer datasheet. At 75 MHz, component placement and interconnect geometry are part of the receiver interface; verify amplitude and timing at the device pins with suitable high-speed test methods.
Do not treat a 56-TSSOP package alone as proof of drop-in compatibility. Before substituting DS90CR288AMTDX/NOPB, compare all 28 data inputs, the clock or strobe, power, ground, and configuration pins, and then verify setup time, hold time, output timing, supply limits, and termination values. Also check the ordering suffix and reel format so the physical part delivered matches the production bill of materials.
Separate the LVDS receiver from noisy switching circuitry and provide a clean return path beneath the differential pairs. If the board also contains switching regulators or high-current digital paths, route those paths away from the receiver inputs and keep their return currents from crossing beneath the signal pairs. A solid ground reference and symmetric pair geometry are especially important when the link crosses multiple board layers.
מידע על תאימות
RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the available product records.