Texas Instruments

DS90CR584MTDX - 65MHz FPD-Link LVDS Receiver | Texas Instruments

料号: DS90CR584MTDX ✗ 停产
4.5 V to 5.5 V Vdss 56-TSSOP Package 65 MHz Speed
最小起订量: 1 |

DS90CR584MTDX 概述

The Texas Instruments DS90CR584MTDX is a 65 MHz FPD-Link LVDS receiver that converts four differential LVDS data streams into 28 CMOS/TTL output bits. Designed for 24-bit color flat-panel display systems, it uses a 4.5 V to 5.5 V supply and is packaged in a 56-pin TSSOP with gull-wing leads. The receiver also complements the DS90CR583 transmitter in the National Semiconductor flat-panel display interface family.

A flat-panel display link is a high-speed serial interface that transfers pixel data between a display controller and a panel timing controller. The DS90CR583 transmitter converts 28 CMOS/TTL input bits into four LVDS streams and transmits a phase-locked clock in parallel over a fifth LVDS link. The DS90CR584 provides the receiving side of that architecture, recovering 28 parallel CMOS/TTL bits from the differential data streams. LVDS is a low-voltage differential-signaling technology used to reduce common-mode noise and support reliable high-speed data transfer over a compact cable or PCB connection.

The principal device characteristics are a 65 MHz operating link rate, four LVDS receiver channels, 28 parallel CMOS/TTL outputs, a 4.5 V to 5.5 V supply range, and a 56-pin TSSOP package. Its four differential data inputs are intended to work with the four data lanes sent by the corresponding transmitter, while the separately transmitted clock supports recovery of the parallel data. The 24-bit color designation relates to the display data carried by the 28-bit parallel interface, which can accommodate color information and associated control bits.

The DS90CR583 and DS90CR584 form an LVDS 24-bit color Flat Panel Display Link operating at 65 MHz. This arrangement separates high-speed differential transmission from the parallel logic-side interface: the transmitter accepts parallel CMOS/TTL data, while the receiver returns differential lanes to parallel CMOS/TTL data. Because the receiver is specified for four data streams, board designers should treat lane routing, connector pin assignments, and clock synchronization as an integrated transmitter-receiver design rather than treating each IC independently.

Typical uses include flat-panel monitor and display-controller boards, industrial panel interfaces, and other systems that pair the receiver with a compatible DS90CR583-family transmitter. The interface can be useful when a cable connection is preferable to a wide parallel bus because the four differential data lanes reduce signal-count requirements while supporting deterministic clock forwarding. System qualification should include the complete cable, connector, receiver, transmitter, and display-timing chain.

Layout is especially important in this high-speed differential interface. Route each LVDS pair as a tightly coupled, impedance-controlled pair and keep the receiver and transmitter ground references properly connected. Avoid adding unnecessary stubs, test pads, or long branches to the differential nets. Decoupling and signal-return paths must also follow the layout guidance in the manufacturer datasheet, particularly around the clock and data inputs.

This page combines the device identity, electrical limits, package information, interface use cases, and lifecycle status for the DS90CR584MTDX. It also provides engineering guidance for display-link implementation, replacement assessment, sourcing through the Request a Quote form, and comparison with related interface devices. Because this exact orderable MPN is listed as obsolete, designers should verify availability and consider an approved redesign rather than assuming that every similar line-driver or LVDS receiver is electrically interchangeable.

直接替换替代料: DS90CR584MTDX ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: DS90CR584MTDX (相同外形与封装尺寸) ——差异在于 Protocol.

Texas Instruments
Protocol: FPD-Link / LVDS
对比 DS90CR584MTDX →

该产品暂无直接替换替代料。

请求替代料

DS90CR584MTDX 规格参数

Device Type Receiver
Receiver Channel Count 4 LVDS receivers
Parallel Output Width 28 bits
Maximum Link Clock 65 MHz
Supply Voltage Range 4.5 V to 5.5 V
Protocol FPD-Link
Signal Standard LVDS
Logic-Side Interface CMOS/TTL
封装 56-TSSOP
Package Width 6.10 mm
Package Body Width 0.240 inch
Terminal Count 56 terminals
Terminal Form Gull wing
安装类型 Surface mount
Temperature Grade Commercial
Packaging Format Tape and reel
生命周期状态 Obsolete
Manufacturer Texas Instruments
Original Manufacturer National Semiconductor

DS90CR584MTDX 0.240 inch 引脚配置指南

DS90CR584MTDX(0.240 inch 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

DS90CR584MTDX 的 0.240 inch 封装引脚图

暂无详细引脚数据: DS90CR584MTDX.

请参阅 数据手册 以查看完整引脚配置。

典型应用

DS90CR584MTDX 适用于 6 应用s: Flat-Panel Monitor Receiver, Industrial Display Controller, Digital Signage Display Board, Medical Display Interface, Point-of-Sale Terminal Display, Legacy Monitor Repair.

📺

Flat-Panel Monitor Receiver

The DS90CR584MTDX fits the display-side receiver position in a 65 MHz FPD-Link system because it converts four differential LVDS data lanes into 28 CMOS/TTL bits for the panel logic. It is used with a compatible DS90CR583-family transmitter, which supplies the phase-locked clock on a separate fifth LVDS link. The 4.5 V to 5.5 V receiver supply and 56-TSSOP package support compact display-controller layouts, although the obsolete lifecycle requires careful system qualification and supply planning.

🏭

Industrial Display Controller

An industrial display controller can use the DS90CR584MTDX when the panel interface follows the DS90CR583/DS90CR584 FPD-Link architecture. The receiver accepts four LVDS data streams and delivers 28 parallel CMOS/TTL outputs, while the transmitter forwards a phase-locked clock for synchronized data recovery. Its 65 MHz clock rating supports the legacy display-link rate, but cable length, connector geometry, grounding, and system timing must be verified for each factory-floor display installation.

📺

Digital Signage Display Board

The DS90CR584MTDX is applicable to digital-signage display boards that retain the National Semiconductor FPD-Link receiver topology. Four LVDS inputs reduce the number of high-speed conductors crossing a display cable compared with a 28-bit parallel bus, while the companion transmitter carries a phase-locked clock over a separate link. The implementation must preserve the original 56-pin TSSOP pinout, 4.5 V to 5.5 V supply limits, and timing margins when adapting the interface to modern signage electronics.

💊

Medical Display Interface

A medical display interface may retain the DS90CR584MTDX when its source electronics use the established DS90CR583/DS90CR584 signaling architecture. The receiver's 65 MHz operation, four LVDS data streams, and 28-bit CMOS/TTL output support the display timing required by the legacy flat-panel link. Because clinical equipment may impose additional safety, EMC, and lifecycle requirements, engineers should validate the entire interface rather than assuming that the obsolete receiver status is acceptable for new production.

🖥️

Point-of-Sale Terminal Display

The DS90CR584MTDX can serve as the panel receiver in a point-of-sale terminal that communicates with a controller through the 65 MHz FPD-Link architecture. Differential LVDS data lanes are useful when reducing cable conductors while the separate clock link supports deterministic transfer of the 28-bit parallel payload. The design must include controlled-impedance routing, connector and cable qualification, and suitable receiver decoupling. The obsolete lifecycle makes future availability a major design consideration for new retail deployments.

🔧

Legacy Monitor Repair

The DS90CR584MTDX is directly relevant to repair and refurbishment of monitors that use the original 65 MHz DS90CR583/DS90CR584 display link. The exact suffix identifies a 56-TSSOP receiver in tape-and-reel packaging, allowing a technician to compare the installed device, pin orientation, supply range, and clock characteristics before replacement. For long-term maintenance, use the Request a Quote form to confirm exact-MPN availability and condition because the manufacturer lists the device as obsolete.

推荐产品汇总

DS90CR583 Compatible FPD-Link transmitter 用于: Flat-Panel Monitor Receiver, Industrial Display Controller, Digital Signage Display Board, Medical Display Interface, Point-of-Sale Terminal Display, Legacy Monitor Repair DS90CR285MTDX Related LVDS channel-link interface 用于: Flat-Panel Monitor Receiver, Industrial Display Controller, Medical Display Interface DS90C383MTDX Texas Instruments 用于: Digital Signage Display Board, Point-of-Sale Terminal Display DS90CR584MTDX Texas Instruments 用于: Legacy Monitor Repair
What is the DS90CR584MTDX?
The DS90CR584MTDX is a 65 MHz FPD-Link receiver that converts four LVDS data streams into 28 parallel CMOS/TTL output bits. According to the manufacturer datasheet information, it operates from a 4.5 V to 5.5 V supply and is intended to pair with the DS90CR583 transmitter in 24-bit color flat-panel display systems. The device is packaged in a 56-pin TSSOP and is listed as obsolete.
What are the key specifications of DS90CR584MTDX that engineers should know?
The DS90CR584MTDX provides four LVDS receiver channels, 28 CMOS/TTL output bits, a 65 MHz link clock, and a 4.5 V to 5.5 V supply range. Manufacturer datasheet information identifies the package as 56-TSSOP with a 0.240-inch, 6.10 mm body width. It is a surface-mount commercial-temperature-grade receiver using FPD-Link signaling. The exact pin assignments and electrical limits should be taken from the manufacturer datasheet.
Where can I download the DS90CR584MTDX datasheet PDF?
The DS90CR584MTDX datasheet can be downloaded from the linked manufacturer-related PDF resource or accessed through the manufacturer product documentation for the DS90CR583/DS90CR584 family. The family document describes the DS90CR583 transmitter, its parallel clock transmission, the four LVDS data streams, and the DS90CR584 receiver that converts those streams into 28 CMOS/TTL bits.
Where can I find the DS90CR584MTDX pinout?
Use the pin-description table and package drawing in the DS90CR583/DS90CR584 manufacturer datasheet to locate the DS90CR584MTDX pinout. The public device information identifies a 56-pin TSSOP but does not enumerate all 56 terminal names, so the package drawing is required for exact assignments. Pay particular attention to supply, ground, differential data, clock, and CMOS/TTL output terminals when assigning PCB tracks.
How does DS90CR584MTDX work with DS90CR583?
The DS90CR583 accepts 28 CMOS/TTL data bits, converts them into four LVDS data streams, and sends a phase-locked clock in parallel over a fifth LVDS link. The DS90CR584MTDX receives the four differential data streams and converts them back into 28 CMOS/TTL bits. Together they implement the 65 MHz LVDS 24-bit color Flat Panel Display Link described in the manufacturer family documentation.
What is the supply voltage of DS90CR584MTDX?
The DS90CR584MTDX operates from 4.5 V to 5.5 V. This supply range appears in the published device specifications and is consistent with its CMOS/TTL receiver architecture. The designer should maintain the power rails within the datasheet limits, provide suitable decoupling, and verify the voltage at the device under both startup and maximum operating conditions.
What is the maximum clock frequency of DS90CR584MTDX?
The specified maximum link clock for DS90CR584MTDX is 65 MHz. At that operating point, the receiver supports the 24-bit color FPD-Link arrangement described for the DS90CR583/DS90CR584 family. Clock timing, data-strobe relationships, propagation delay, and setup or hold requirements must be evaluated from the manufacturer datasheet for the complete transmitter, receiver, and interconnect path.
Is DS90CR584MTDX suitable for flat-panel display applications?
Yes, DS90CR584MTDX is specifically associated with 24-bit color Flat Panel Display Link systems. It receives four LVDS streams and provides a 28-bit CMOS/TTL parallel output, matching the display-side architecture of the DS90CR583 transmitter. Suitability for a particular panel depends on timing compatibility, connector and cable behavior, supply sequencing, and successful validation of the complete display link.
Can DS90CR584MTDX replace DS90CR583MTDX?
No. DS90CR584MTDX is the receiver, while the DS90CR583 family member is the transmitter. Although both support the same 65 MHz FPD-Link concept and belong to the 56-pin display-interface family, their signal directions and board roles are different. They are functional counterparts and should be used together rather than treated as interchangeable pin-compatible drop-in devices.
What is the best drop-in replacement for DS90CR584MTDX?
No verified 56-pin TSSOP drop-in replacement for DS90CR584MTDX was identified in the available cross-reference results. The obsolete status requires a pin-by-pin and timing-compatible solution rather than a generic line-driver substitute. Use the Request a Quote form on this page for exact-MPN sourcing, and ask the manufacturer or a qualified specialist to evaluate any proposed receiver against the original datasheet.
What can replace DS90CR584MTDX in a display design?
A suitable replacement must provide four LVDS receiver channels, 28 CMOS/TTL outputs, a 56-TSSOP footprint, and timing compatible with the intended transmitter and panel link. The available cross-reference material does not establish a verified drop-in replacement, so changing the device without a full electrical review is not recommended. Treat the replacement search as a structured display-interface redesign, including protocol, clocking, pinout, and signal-integrity validation.
Is DS90CR584MTDX the same as DS90CR285MTDX?
No. DS90CR584MTDX is a 65 MHz, 28-bit FPD-Link receiver with four LVDS input streams, while DS90CR285MTDX is identified as a 3.3 V rising-edge data-strobe LVDS transmitter for a 28-bit channel-link application. Their roles, supply arrangements, and link architectures differ, so they are not direct replacements even though both use low-voltage differential signaling.
When should I choose DS90CR584MTDX over another LVDS interface IC?
Choose DS90CR584MTDX when the design specifically requires the legacy 65 MHz FPD-Link interface with four LVDS data lanes, a separately forwarded phase-locked clock, and 28 parallel CMOS/TTL outputs in a 56-TSSOP package. Choose another interface IC when the transmitter protocol, supply voltage, lane count, clocking method, or connector architecture differs. Exact legacy timing compatibility is more important than broad LVDS functionality.
Is DS90CR584MTDX in stock?
Stock status for DS90CR584MTDX should be requested through the Request a Quote form on this page because the exact device is listed as obsolete and available inventory can vary by lot and packaging condition. The manufacturer product and distributor records identify the MPN and its historical channel structure, but current stock, minimum order quantity, and delivery timing require a current quotation for the exact suffix.
Where can I buy DS90CR584MTDX and what is its price?
Use the Request a Quote form on this page for the current price, stock, lot condition, and delivery schedule for DS90CR584MTDX. The exact orderable part is a 56-TSSOP, tape-and-reel device that is marked obsolete, so commercial terms can depend on remaining inventory and traceability. Supply the required quantity and datecode requirements with the request to obtain an actionable quotation.
What is the lead time for DS90CR584MTDX?
The current lead time for DS90CR584MTDX should be confirmed through the Request a Quote form on this page. Because this exact MPN is obsolete, lead time depends on available factory inventory, remaining volume, inspection requirements, and packaging configuration. A quotation request stating the required quantity, datecode preference, and target delivery date enables the supplier to confirm a meaningful schedule.
How should DS90CR584MTDX LVDS pairs be routed on a PCB?
Route the DS90CR584MTDX LVDS inputs as short, tightly coupled differential pairs with continuous reference planes and controlled impedance. Avoid long stubs, unnecessary test pads, and branch connections that can degrade the 65 MHz signal. Follow the manufacturer pinout and recommended decoupling layout, and validate the complete transmitter-to-receiver path with the intended connector and cable because edge rates can exceed the link clock frequency.

工程参考数据: DS90CR584MTDX ——对比、设计指导和合规信息。

选型指南

Choose DS90CR584MTDX when repairing or maintaining an existing display system whose controller uses the DS90CR583/DS90CR584 65 MHz FPD-Link architecture and whose receiver footprint is a 56-TSSOP. It is specifically positioned as the four-LVDS-channel receiver with 28 CMOS/TTL outputs. Choose DS90CR583 when the required board role is the complementary transmitter, not as a substitute for the receiver. Do not select DS90CR285MTDX or DS90C383MTDX solely because they also use LVDS; their direction, supply arrangement, protocol, and timing must be checked independently. For new designs, prefer a currently supported interface unless maintaining the obsolete part is mandatory. For a drop-in replacement, require identical pin assignments, compatible LVDS thresholds and timing, suitable supply decoupling, and validated operation with the actual transmitter, connector, and cable.

与替代料对比

参数 本产品
Package 56-TSSOP
Brand Texas Instruments
Device Type Receiver
Receiver Channels 4 LVDS receivers
Parallel Output Width 28 bits
Maximum Link Clock 65 MHz
Supply Voltage Range 4.5 V to 5.5 V
Protocol FPD-Link
Logic Interface CMOS/TTL
Lifecycle Status Obsolete

关键差异点

  • Purpose-built receiver role in the legacy FPD-Link pair (对比 DS90CR583)
  • Established 65 MHz flat-panel-link architecture (对比 DS90CR285MTDX)
  • Defined 28-bit receiver interface (对比 DS90C383MTDX)

设计说明

Route the four LVDS data pairs as tightly coupled, impedance-controlled nets with a continuous reference plane. Keep the inputs short and avoid stubs, long test-point branches, or unnecessary layer transitions. The 65 MHz link clock does not by itself represent the slowest edge rate, so use the transmitter and receiver rise-time specifications when setting trace geometry and termination.

Treat the DS90CR583 transmitter, phase-locked clock link, DS90CR584MTDX receiver, connector, and cable as one signal path. Verify differential voltage, common-mode limits, propagation delay, clock-data alignment, and connector loss against the manufacturer datasheet. Validate the assembled board with representative cable lengths because reflections and loss can degrade margin even when the nominal link clock remains below 65 MHz.

Operate the receiver from a regulated supply within the specified 4.5 V to 5.5 V range. Place decoupling capacitors close to the supply and ground terminals, and provide a low-impedance return path beneath the device. Check the supply voltage at the IC under transmitter activity and panel-load transients; clock and data activity can produce supply disturbance that affects receiver margins.

Do not substitute the DS90CR583 transmitter for the DS90CR584MTDX receiver or assume that any 28-bit LVDS receiver is interchangeable. Confirm all 56 terminal assignments, the four data-pair mapping, the separately transmitted clock connection, supply pins, and ground pins from the family datasheet. The exact-MPN obsolete status also means that package marking and lot documentation should be checked during repair or replacement.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact MPN. The device is a commercial-temperature-grade display interface IC, so AEC-Q100 is not applicable based on its stated temperature grade.

相关搜索

DS90CR584MTDX datasheet DS90CR584MTDX pinout DS90CR584MTDX datasheet pdf DS90CR584MTDX specifications DS90CR584MTDX equivalent DS90CR584MTDX replacement DS90CR584MTDX cross reference DS90CR584MTDX price DS90CR584MTDX stock Texas Instruments DS90CR584MTDX DS90CR584MTDX 65MHz LVDS receiver DS90CR584MTDX 56-TSSOP

相关元器件 & 术语

Texas Instruments National Semiconductor DS90CR584MTDX DS90CR583 DS90CR285MTDX DS90C383MTDX FPD-Link LVDS Low Voltage Differential Signaling CMOS/TTL line driver receiver flat-panel display link 24-bit color display 65 MHz clock four LVDS data streams 28-bit parallel output 56-TSSOP gull-wing package surface mount 4.5 V to 5.5 V supply phase-locked transmit clock differential signaling obsolete component
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情