DS90LV019TMTCX - 3.3V/5V LVDS Transceiver | Texas Instruments
料号: DS90LV019TMTCX ✓ 量产中DS90LV019TMTCX 概述
An LVDS transceiver is a high-speed interface device that combines a differential line driver, a differential receiver, and associated biasing or termination functions. Within the interface hierarchy, it belongs to the line-driver and receiver class, then to LVDS interface ICs, and ultimately to the broader semiconductor category. Differential signaling reduces sensitivity to common-mode noise because the receiving circuit evaluates the voltage difference between two conductors rather than the voltage referenced to ground.
The device supports both 3.3 V and 5 V operation, provides one transmit and one receive path, and uses a flow-through pin arrangement that supports short PCB routing between logic and differential pins. According to the Texas Instruments product page, the DS90LV019 is intended for high-speed, low-power point-to-point interconnects. Its operating temperature range is -40 °C to +85 °C.
The DS90LV019 uses current-mode differential signaling to keep power dissipation controlled at higher data rates. Cross-reference information reports a 3.5 mA output loop current and a 0.45 V differential output level. The receiver converts the differential LVDS input into a single-ended TTL-compatible output, allowing the same device to bridge a TTL source and an LVDS link.
Typical uses include clock distribution, point-to-point data links, telecom equipment, industrial controllers, test and measurement systems, and embedded backplane interconnects. The 14-pin TSSOP package is suitable for compact multilayer PCB designs where a conventional dual-row surface-mount footprint is preferred over larger leaded packages.
For reliable LVDS operation, place the differential pair on a controlled-impedance PCB layer, keep the two traces closely coupled, terminate the receiver as recommended by the manufacturer, and avoid routing the pair through noisy power or switching regions. Confirm the board's trace impedance and connector or cable loss before selecting a long cable or high data rate.
This page consolidates manufacturer specifications, distributor package information, verified drop-in cross-references, interface-comparison parameters, and practical PCB guidance so engineers can evaluate the DS90LV019TMTCX as a complete LVDS interface solution.
直接替换替代料: DS90LV019TMTCX ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
DS90LV019TMTCX/NOPB
✅ 直接替换📋 参考替代料(不在目录中)
DS90LV019TMTC/NOPB
✅ 直接替换📋 参考替代料(不在目录中)
DS90LV019TMTC
✅ 直接替换📋 参考替代料(不在目录中)
DS90LV019TMTCX 规格参数
| Device Type | LVDS line driver and receiver |
| 电源电压 | 3.3 V or 5 V |
| Maximum Data Rate | 100 Mbps |
| Number of Transmitters | 1 |
| Number of Receivers | 1 |
| Logic Interface | TTL-compatible |
| Differential Interface | LVDS |
| LVDS Standards | EIA-644-A and TIA-644-A |
| Output Loop Current | 3.5 mA |
| Differential Output Level | 0.45 V |
| 工作温度 | -40 °C to +85 °C |
| 封装 | 14-pin TSSOP (PW) |
| 安装类型 | Surface mount |
| Pin Arrangement | Flow-through pinout |
| Applications | High-speed, low-power point-to-point interconnects |
DS90LV019TMTCX 14-pin tssop (pw) 引脚配置指南
DS90LV019TMTCX(14-pin tssop (pw) 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: DS90LV019TMTCX.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DS90LV019TMTCX 适用于 6 应用s: Point-to-Point Clock Distribution, Industrial Control Data Link, Telecom and Network Equipment Interface, Test and Measurement Signal Link, Embedded Backplane Interconnect, Low-Power Differential Signal Conditioning.
Point-to-Point Clock Distribution
The DS90LV019TMTCX fits a low-power differential clock link that must operate at up to 100 Mbps. Its 3.3 V or 5 V supply compatibility allows the LVDS side to coexist with either 3.3 V or 5 V TTL logic in the same system. Use the flow-through package arrangement to keep the differential traces short and route the two conductors as a coupled pair. The receiver converts the differential clock back to a single-ended output while the driver provides noise-resistant transmission over a PCB or short cable. Confirm termination, jitter budget, and output edge rate against the system clock requirement before releasing the layout.
推荐
Industrial Control Data Link
The DS90LV019TMTCX is appropriate for a compact industrial controller that must move a single-ended control or status signal across a board-to-board LVDS connection. Differential current-mode signaling reduces susceptibility to common-mode disturbance, while the 100 Mbps capability provides useful margin over slow control traffic. The 14-pin TSSOP package simplifies assembly and supports compact multilayer boards. Place the differential route away from motor-control and relay-switching nodes, implement the manufacturer-recommended receiver termination, and verify that the industrial environment does not require a wider operating temperature grade.
推荐
Telecom and Network Equipment Interface
The DS90LV019TMTCX can serve as a point-to-point interface element in telecom or network equipment where a TTL-compatible source must reach a differential LVDS link. Operation from 3.3 V or 5 V provides flexibility across line-card and control-board supply plans. The device's single driver and receiver support dedicated signaling paths without a multi-channel transceiver's pin overhead. In a high-density chassis, route the pair over a continuous plane, maintain the specified differential impedance, and keep connectors and cable assemblies short enough to preserve the usable eye at the intended data rate.
推荐
Test and Measurement Signal Link
The DS90LV019TMTCX is suitable for carrying a single-ended trigger, status, or synchronization signal between measurement instrument sections over LVDS. Differential transmission helps reduce susceptibility to coupling from adjacent analog and switching circuitry. The 100 Mbps maximum data rate accommodates many control and synchronization paths, while the small 14-pin TSSOP footprint leaves more board area for analog components. Keep the differential pair short, provide the specified receiver termination, and separate it from high-impedance analog inputs to minimize crosstalk into the measurement system.
推荐
Embedded Backplane Interconnect
The DS90LV019TMTCX can bridge a TTL-compatible processor or controller to a low-voltage differential backplane segment. Its flow-through pin arrangement supports straightforward routing between logic circuitry and a connector, while the 14-pin TSSOP package is compatible with dense board layouts. The differential interface limits common-mode pickup when the link crosses areas near switching regulators or backplane drivers. Define the backplane impedance and receiver termination consistently, minimize stub lengths, and validate signal integrity with the actual connector and layer stack-up rather than assuming ideal point-to-point conditions.
推荐
Low-Power Differential Signal Conditioning
The DS90LV019TMTCX is useful when a design must convert a single-ended TTL signal into LVDS and recover it at the far end without adopting a multi-channel, higher-power interface device. The 3.3 V and 5 V operating options permit placement near either logic family, and the current-mode driver supports controlled power dissipation at elevated data rates. Use the driver when the link length or connector environment creates ground-offset problems, then terminate the receiver as directed by the manufacturer. This arrangement improves noise immunity without changing the originating logic voltage domain.
推荐
推荐产品汇总
工程参考数据: DS90LV019TMTCX ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DS90LV019TMTCX/NOPB | DS90LV019TMTC/NOPB | DS90LV019TMTC |
|---|---|---|---|---|
| Package | 14-TSSOP (PW) | 14-TSSOP (PW) | 14-TSSOP (PW) | 14-TSSOP (PW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Supply Voltage | 3.3 V or 5 V | 3.3 V or 5 V | 3.3 V or 5 V | 3.3 V or 5 V |
| Maximum Data Rate | 100 Mbps | 100 Mbps | 100 Mbps | 100 Mbps |
| Number of Transmitters | 1 | 1 | 1 | 1 |
| Number of Receivers | 1 | 1 | 1 | 1 |
关键差异点
- Documented pin-compatible replacement coverage within the DS90LV019 family (对比 DS90LV019TMTCX/NOPB)
- Flow-through TSSOP organization supports practical point-to-point routing (对比 DS90LV019TMTC/NOPB)
- Dual 3.3 V and 5 V supply compatibility expands board-level integration options (对比 DS90LV019TMTC)
设计说明
Route the DS90LV019TMTCX differential pair as a tightly coupled, length-matched pair on a continuous reference plane. Define the target differential impedance from the actual PCB stack-up and preserve that geometry through connectors and vias. The flow-through package helps minimize routing length, but the driver and receiver pins still require the arrangement shown in the manufacturer pin-description table.
Apply the receiver termination specified by the manufacturer and place it close to the receiver inputs. Confirm the resistance and any fail-safe arrangement from the Texas Instruments datasheet rather than copying a termination from a different LVDS device. Keep the pair away from switching-regulator inductors, relay contacts, and high-current return paths, and validate the complete connector and cable path with an eye or compliance measurement.
Do not substitute the 3.3 V-only descriptions found in some third-party listings for the full manufacturer specification, which identifies the DS90LV019 as a 3.3 V or 5 V device. Likewise, verify the 14-pin TSSOP package rather than the SOT-23 package listed by an incorrect aggregation result. Before substitution, confirm the complete orderable suffix, supply range, data rate, temperature range, and receiver termination arrangement.
Provide a quiet return path beneath the differential interface and avoid splitting the reference plane beneath the pair. If the signal must cross a plane boundary, add a stitching capacitor near the interface and re-evaluate the return current path. Avoid placing test points on only one conductor unless the fixture has been designed for a properly terminated differential connection.
合规信息
The manufacturer product and distributor listings do not explicitly state each environmental-compliance field. AEC-Q100 is marked not applicable because this is a general-purpose interface IC rather than an automotive-qualified device.