DSPIC33CK128MC503T-I/M5 - 16-bit DSC 128KB Flash CAN FD | Microchip
料号： DSPIC33CK128MC503T-I/M5 ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $4.62 | $4.62 |
| 10 | $4.15 | $41.50 |
| 100 | $3.71 | $371.00 |
| 500 | $3.34 | $1,670.00 |
| 1,000 | $3 | $3,000.00 |
DSPIC33CK128MC503T-I/M5 概述
A digital signal controller combines the compute throughput of a DSP with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy, the dsPIC33CK family sits between general-purpose MCUs and dedicated DSPs, offering single-cycle MAC/DSP instructions, fast interrupt handling, and deterministic control loops that make it the natural choice for closed-loop power conversion and motor control systems.
Key features include the single 100 MHz dsPIC DSC core with DSP-enhanced instruction set, on-chip operational amplifiers, a 12-bit high-speed ADC, advanced high-resolution PWM modules, and a CAN FD controller for automotive and industrial networking. Four DMA channels offload data movement from the CPU, and an internal fast RC oscillator with PLL removes the need for an external crystal in many designs.
Architecturally, the device uses a CMOS process with a modified Harvard bus, executing from zero-wait-state FLASH at full core speed. The ADC-PWM-OpAmp connectivity allows analog feedback loops to be closed entirely on-chip, minimizing CPU overhead in digital power applications. The Mouser listing explicitly identifies OpAmps, 12-bit ADC, PWM, and CAN FD as the peripheral set of this part.
Typical applications include brushless DC and PMSM motor control, digital switched-mode power supplies (LLC, totem-pole PFC), solar micro-inverters, and battery-management systems where CAN FD connectivity is required.
Designers should note the family supply range of approximately 3.0V to 3.6V and must budget the UQFN thermal pad soldering for reliable ground return during high-frequency PWM operation.
This page synthesizes distributor pricing, drop-in family alternatives, application guidance, and design notes not found in the manufacturer datasheet alone.
直接替换替代料： DSPIC33CK128MC503T-I/M5 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： DSPIC33CK128MC503T-I/M5 （相同外形与封装尺寸） ——差异在于 Package, Operating Temperature, Core, Program Memory Size, Packaging.
快速对比工具——选择替代料号进行并排对比：
DSPIC33CK128MC503T-E/M5
✅ 直接替换📋 参考替代料（不在目录中）
DSPIC33CK128MC503T-H/M5
✅ 直接替换📋 参考替代料（不在目录中）
DSPIC33CK256MC503T-I/M5
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
DSPIC33CK64MC503T-I/M5
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
DSPIC33CK32MC503T-I/M5
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
DSPIC33CK128MC503T-I/M5 最大额定值与电气特性
| Core Processor | dsPIC33CK (16-bit dsPIC DSC) |
| Core Size | 16-bit |
| 最大时钟频率 | 100 MHz |
| Program Memory Size | 128 KB (128K x 8) FLASH |
| RAM Size | 16 KB |
| Connectivity | CAN FD, I2C, SPI, UART/USART |
| Peripherals | OpAmps, 12-bit ADC, High-Resolution PWM, DMA |
| DMA Channels | 4 |
| 封装 | 36-UQFN (5x5 mm) |
| 安装类型 | Surface Mount |
| 工作温度 | -40C to +85C (I grade) |
| Technology | CMOS |
| Internal Oscillator | Yes (FRC with PLL) |
| 电源电压 | 3.0 V to 3.6 V (typical family range) |
| Packaging | Tape & Reel (T suffix) |
| RoHS 状态 | Compliant |
| Product Family | dsPIC33CK128MC50x Digital Signal Controllers |
DSPIC33CK128MC503T-I/M5 36-uqfn (5x5 mm) 引脚配置指南
DSPIC33CK128MC503T-I/M5（36-uqfn (5x5 mm) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： DSPIC33CK128MC503T-I/M5.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DSPIC33CK128MC503T-I/M5 适用于 6 应用s: BLDC / PMSM Motor Control, Digital Power Conversion (LLC / Totem-Pole PFC), Battery Management Systems with CAN FD, Solar Micro-Inverters, Industrial Sensing and Condition Monitoring, Automotive Body and Actuator Control Nodes.
BLDC / PMSM Motor Control
The DSPIC33CK128MC503T-I/M5 fits motor control because its 100 MHz DSP core executes field-oriented control (FOC) inner loops at 20-50 kHz with single-cycle MAC instructions, while the high-resolution PWM provides sub-nanosecond duty and dead-time adjustment for efficient sine-wave drive. The on-chip op-amps amplify low-side shunt currents directly, feeding the 12-bit ADC synchronously with PWM triggers so phase-current sampling is free of switching noise. In a typical PMSM servo drive, the DSC closes the current loop on-chip with ADC-DMA-PWM interconnects that add no CPU latency, reserving the CPU for the speed loop and communication. The CAN FD interface links the drive to a higher-level controller without an external CAN transceiver-controller pair.
推荐
Digital Power Conversion (LLC / Totem-Pole PFC)
For digital switched-mode power supplies such as LLC resonant converters and totem-pole PFC stages, the DSPIC33CK128MC503T-I/M5 offers the deterministic analog-to-PWM datapath the topology demands. The 12-bit ADC samples input/output voltage and inductor current at rates up to millions of samples per second, and dedicated PWM-to-ADC triggers guarantee samples land at the midpoint of the switching period, removing ripple error. High-resolution PWM (sub-nanosecond steps) enables precise phase-shift and frequency control of LLC half-bridges, while the 100 MHz core runs voltage-mode or current-mode compensators at per-cycle rates. The internal FRC oscillator with PLL eliminates the external crystal, reducing BOM cost in isolated and compact power supplies.
推荐
Battery Management Systems with CAN FD
In battery management systems, the DSPIC33CK128MC503T-I/M5 serves as the pack controller, combining multi-channel 12-bit ADC cell-voltage monitoring, on-chip op-amp current-shunt amplification, and a native CAN FD interface for vehicle or rack-level communication. The 128 KB FLASH holds state-of-charge and state-of-health algorithms including lookup tables and filtering code, while 16 KB RAM buffers measurement history. The industrial -40C to +85C operating range covers automotive cabin and industrialESS environments. Hardware DMA streams ADC results to RAM without CPU intervention, keeping worst-case interrupt latency low so protection functions (over-current, over-temperature) execute within microseconds of a fault event.
推荐
Solar Micro-Inverters
Solar micro-inverters require simultaneous MPPT control, grid-synchronized current injection, and safety compliance in a compact, thermally constrained enclosure - a match for the DSPIC33CK128MC503T-I/M5's integrated feature set. The high-resolution PWM synthesizes the unipolar SPWM drive for the DC-DC and DC-AC stages, while the 12-bit ADC with DMA samples panel voltage/current and grid voltage for phase-locked-loop grid synchronization at per-switching-cycle rates. The 100 MHz DSP core runs MPPT perturb-and-observe or incremental-conductance algorithms concurrently with the control loops. On-chip op-amps condition AC current-sense signals, removing an external amplifier stage and shrinking PCB area.
推荐
Industrial Sensing and Condition Monitoring
For vibration, pressure, and current condition-monitoring nodes, the DSPIC33CK128MC503T-I/M5 provides 12-bit analog acquisition, on-chip signal amplification, and digital filtering using its DSP multiply-accumulate capability, all in a single 5x5 mm device. The 128 KB FLASH stores FFT or FIR-filter firmware plus communication stacks, while the CAN FD or UART interfaces feed processed features to a PLC or gateway. The internal FRC oscillator supports startup without a crystal, and the industrial temperature rating covers cabinet-mounted installations. Four DMA channels enable continuous multi-channel capture - for example, three op-amp-amplified vibration channels sampled synchronously - without CPU loading, extending battery or loop-powered operation margins.
推荐
Automotive Body and Actuator Control Nodes
The DSPIC33CK128MC503T-I/M5 supports automotive-adjacent actuator control - DC-mirror, pump, fan, and throttle modules - where CAN FD networking and deterministic motor control must coexist. The native CAN FD controller communicates with body controllers at FD data rates without an external protocol chip, and the high-resolution PWM plus 12-bit ADC closes current loops for brushed or BLDC actuators at audibly quiet PWM frequencies. The industrial -40C to +85C grade suits under-dash and trunk zones; for under-hood zones, designers can pin-select the same-footprint -E or -H temperature grade variants without PCB changes. The 100 MHz core also runs sensorless BEMF observers, removing hall-sensor wiring cost.
推荐
推荐产品汇总
工程参考数据： DSPIC33CK128MC503T-I/M5 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DSPIC33CK128MC503T-E/M5 | DSPIC33CK128MC503T-H/M5 | DSPIC33CK256MC503T-I/M5 | DSPIC33CK64MC503T-I/M5 | DSPIC33CK32MC503T-I/M5 |
|---|---|---|---|---|---|---|
| Package | 36-UQFN (5x5 mm) | 36-UQFN (5x5 mm) - same | 36-UQFN (5x5 mm) - same | 36-UQFN (5x5 mm) - same | 36-UQFN (5x5 mm) - same | 36-UQFN (5x5 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| FLASH Program Memory | 128 KB | 128 KB | 128 KB | 256 KB | 64 KB | 32 KB |
| RAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| Core Speed | 100 MHz | 100 MHz | 100 MHz | 100 MHz | 100 MHz | 100 MHz |
| Operating Temperature | -40C to +85C (I) | Extended range (-E) | High temperature (-H) | -40C to +85C (I) | -40C to +85C (I) | -40C to +85C (I) |
| CAN FD | Yes | Yes | Yes | Yes | Yes | Yes |
| Relative Cost (qty 1) | Baseline (~$4.62 as of 2026-09-22) | Higher (extended grade premium) | Higher (high-temp grade premium) | Higher (~+15-25%) | Lower (~-10-20%) | Lowest (~-20-30%) |
关键差异点
- Balanced 128 KB FLASH density at mid-family cost （对比 DSPIC33CK256MC503T-I/M5)
- Full FLASH headroom vs low-cost family member （对比 DSPIC33CK64MC503T-I/M5)
- Industrial temperature grade for standard environments （对比 DSPIC33CK128MC503T-H/M5)
设计说明
The 36-UQFN (5x5 mm) M5 package has a central exposed thermal pad that must be soldered to a grounded copper array for both thermal dissipation and the low-inductance ground return needed by fast PWM edges. Follow Microchip UQFN layout guidelines: via array of 4-9 vias under the pad connected to internal ground planes, and keep the decoupling capacitors for VDD, AVDD, and VDDCORE within 2 mm of their respective pins. Estimated: a 0.5 W dissipation in a 5x5 QFN with a solid ground plane typically yields theta_JA in the 40-50 C/W range - verify against the datasheet thermal table for your stack-up.
Power the dsPIC33CK core from a clean 3.3 V rail within the family range (approximately 3.0-3.6 V). The internal LDO requires its VDDCORE capacitor - typically 1 uF ceramic per Microchip reference designs - placed at the pin; omitting it prevents startup. During PWM-heavy motor control, the ADC reference should be separate from the noisy digital VDD: use AVDD filtered through an RC or ferrite bead, or a precision reference on the VREF+ pin for the 12-bit ADC to reach its effective-number-of-bits potential in current-sense loops.
High-resolution PWM outputs with sub-nanosecond edge resolution will couple into ADC inputs if layout is careless. Route op-amp and ADC analog traces away from PWM gate-drive signals, guard analog routing with ground, and use PWM-triggered ADC sampling at the switch-node quiet window. Common pitfall: remappable RPx pins let you place CAN TX/RX or UART on any pin, but verify the Peripheral Pin Select assignments before finalizing layout - swapping PPS later requires a PCB respin.
Distinguish order-code variants before purchase: the T suffix means Tape & Reel, and the -I/-E/-H suffixes denote industrial/extended/high temperature grades - they are footprint-compatible but not interchangeable in thermally demanding environments. Also note some third-party listings cite a 64 MHz maximum clock for this family; the Microchip family page states a single 100 MHz dsPIC DSC core, so design to the official 100 MHz figure and confirm Fcy configuration (PLL dividers) in code against the current datasheet.
合规信息
RoHS compliance inferred from current-production Microchip DSC status on distributor listings; REACH and halogen-free certificates were not stated in the provided data - verify on the Microchip product page certificate portal.