DSPIC33EP128GM310T-I/PT - 70 MIPS 128KB DSC | Microchip
料号： DSPIC33EP128GM310T-I/PT ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $7.2 | $7.20 |
| 10 | $6.48 | $64.80 |
| 100 | $5.76 | $576.00 |
| 500 | $5.22 | $2,610.00 |
| 1,000 | $4.68 | $4,680.00 |
DSPIC33EP128GM310T-I/PT 概述
Key features include twelve Motor Control PWM (MCPWM) channels, eight input capture and eight output capture/compare channels, two quadrature encoder interfaces (QEI), four integrated operational amplifiers, a Charge Time Measurement Unit (CTMU), and a Parallel Thumb Generator (PTG) hardware sequencer. The four on-chip op-amps allow current-sense amplification directly inside the MCU, reducing bill-of-material cost in inverter designs. Thirteen timers and four DMA channels offload data movement from the CPU.
Technically, the dsPIC33EP core runs from a 3.3V supply with an industrial temperature rating of -40C to +85C (the /I suffix). DSP engine features include two 40-bit accumulators, 17-bit x 17-bit single-cycle multiply, and hardware divide support, enabling FOC (field-oriented control) motor algorithms with fast interrupt latency.
Typical applications include three-phase brushless DC and PMSM motor drives, solar inverters, digital power supplies, and industrial automation nodes. The dual QEI inputs make it especially well suited to servo positioning with incremental encoders.
Design consideration: budget the 3.3V rail decoupling carefully across the four supply pin groups, and keep PWM routing away from the analog op-amp inputs to preserve signal integrity. This page synthesizes datasheet specifications, drop-in same-family alternatives, and practical design notes not found on distributor listing pages.
直接替换替代料： DSPIC33EP128GM310T-I/PT ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： DSPIC33EP128GM310T-I/PT （相同外形与封装尺寸） ——差异在于 Package, Quadrature Encoder Interfaces, Operating Temperature, Core Architecture, Input Capture / Output Compare.
快速对比工具——选择替代料号进行并排对比：
DSPIC33EP128GM310T-E/PT
✅ 直接替换📋 参考替代料（不在目录中）
DSPIC33EP256GM310T-I/PT
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$4.95 / 个
查看数据手册 →DSPIC33EP64GM310T-I/PT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
DSPIC33EP256GM710T-I/PT
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$5.25 / 个
查看数据手册 →DSPIC33EP128GM310T-I/PT 最大额定值与电气特性
| Core Architecture | 16-bit dsPIC33E DSC (Harvard) |
| Max CPU Speed | 70 MIPS (60 MHz max clock) |
| Program Memory (Flash) | 128 KB (43K x 24) |
| RAM | 16 KB |
| 电源电压 | 3.3 V |
| Motor Control PWM Channels | 12 MCPWM |
| Input Capture / Output Compare | 8 IC / 8 OC |
| Quadrature Encoder Interfaces | 2 QEI |
| On-chip Op-Amps | 4 |
| CTMU | Yes (Charge Time Measurement Unit) |
| PTG | Yes (Parallel Thumb Generator hardware sequencer) |
| Timers | 13 |
| DMA Channels | 4 |
| 工作温度 | -40C to +85C (Industrial, /I) |
| 封装 | 100-TQFP, 12x12x1 mm |
| 安装类型 | Surface Mount |
| Packaging | Tape & Reel (T suffix) |
DSPIC33EP128GM310T-I/PT 100-tqfp, 12x12x1 mm 引脚配置指南
DSPIC33EP128GM310T-I/PT（100-tqfp, 12x12x1 mm 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： DSPIC33EP128GM310T-I/PT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DSPIC33EP128GM310T-I/PT 适用于 6 应用s: Three-Phase BLDC/PMSM Motor Drives, Solar String Inverters and MPPT Converters, Industrial Servo and Motion Control, Digital Power Supplies (LLC, PFC, Buck), Battery Management and Charging Systems, Embedded Industrial Sensing and Automation Nodes.
Three-Phase BLDC/PMSM Motor Drives
The DSPIC33EP128GM310T-I/PT is purpose-built for field-oriented control of brushless DC and permanent-magnet synchronous motors. Its 70 MIPS DSP core executes single-cycle 17x17 multiplies with dual 40-bit accumulators, sustaining 20 kHz current loops with margin, while 12 MCPWM channels generate complementary PWM pairs with hardware dead-time insertion for a full three-phase inverter. The two QEI modules interface directly with incremental encoders for position feedback, and the four on-chip op-amps amplify low-side shunt currents without external amplifiers, cutting BOM cost. Designers should place the op-amp inputs adjacent to shunt resistors and use the PTG sequencer to automate ADC sampling synchronized to PWM centers for minimal ripple in current measurements.
推荐
Solar String Inverters and MPPT Converters
In grid-tied solar micro-inverters and string-inverter DC-DC stages, the DSPIC33EP128GM310T-I/PT supplies both the control bandwidth and the analog integration needed for MPPT and grid-current shaping. The 12 MCPWM channels drive interleaved boost and full-bridge stages with phase-shifted carriers, and the DSP engine performs the multiply-heavy MPPT and PLL algorithms at 70 MIPS. The CTMU supports precise sensing tasks and the four op-amps buffer voltage/current feedback signals on-chip. With 128KB Flash there is ample room for grid-standard compliance code and a bootloader. Place analog feedback traces away from PWM switching nodes and synchronize ADC sampling to PWM troughs to reject switching noise in current loops.
推荐
Industrial Servo and Motion Control
For servo axes in factory automation, the dual QEI modules of the DSPIC33EP128GM310T-I/PT accept two independent incremental encoder inputs, enabling single-chip control of dual-axis or master/slave motion systems. The 8 input-capture channels timestamp encoder index and hall events in hardware, offloading the CPU, while 13 timers and 4 DMA channels keep trajectory calculations deterministic. The 16KB RAM holds position profiles and filter states, and the PTG hardware sequencer automates repetitive sampling sequences without CPU intervention. Industrial deployments use the -40C to +85C /I rating; for sealed drives near motors, the /E extended-temperature variant (same footprint) provides +125C capability without PCB change.
推荐
Digital Power Supplies (LLC, PFC, Buck)
The DSPIC33EP128GM310T-I/PT implements voltage-mode and current-mode control for LLC resonant converters, PFC stages, and high-current bucks. Adaptive dead-time control on the MCPWM peripheral maximizes efficiency in resonant topologies, and phase-shifted PWM outputs support interleaved PFC with current sharing. The 70 MIPS core closes voltage loops at tens of kHz with 3P3Z or PID compensators, and the on-chip op-amps handle average-current-mode sensing. Firmware protection - cycle-by-cycle current limit and fault shutdown - is enforced in hardware via PWM fault inputs. Keep the analog ground plane split from power ground under the controller and route feedback through a star connection at the IC ground pin.
推荐
Battery Management and Charging Systems
In BMS masters and smart chargers, the DSPIC33EP128GM310T-I/PT combines the CTMU charge-time measurement unit for precise sensing tasks with the on-chip op-amps for current-loop feedback in CC/CV charging profiles. The 12 MCPWM channels drive multi-phase charging bridges, and the 3.3V industrial-rated device monitors cell-string voltage through the ADC channel set. Its 128KB Flash stores state-of-charge algorithms, fault logs, and a field-updatable bootloader, while UART/SPI communication links the BMS to vehicle or inverter controllers. For outdoor and under-hood environments, specify the /E temperature variant. Ensure the CTMU calibration routine from the Microchip datasheet runs at startup to meet measurement accuracy targets.
推荐
Embedded Industrial Sensing and Automation Nodes
As a general automation node, the DSPIC33EP128GM310T-I/PT merges signal conditioning and control in one chip: the four op-amps amplify sensor outputs (pressure bridges, pH probes, thermistor dividers), the CTMU measures capacitance for touch or liquid-level sensing, and the PTG hardware sequencer automates sample-and-decide-report cycles with minimal CPU load. Eight input captures timestamp flowmeter and event pulses, and remappable peripheral pin selection adapts the 85 I/O to arbitrary wiring conventions. Remapped UART/SPI/I2C links connect to SCADA gateways. This integration removes an external analog front-end stage, cutting board area and drift sources in distributed I/O modules deployed at -40C to +85C.
推荐
推荐产品汇总
工程参考数据： DSPIC33EP128GM310T-I/PT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DSPIC33EP128GM310T-E/PT | DSPIC33EP256GM310T-I/PT | DSPIC33EP64GM310T-I/PT | DSPIC33EP256GM710T-I/PT |
|---|---|---|---|---|---|
| Package | 100-TQFP (12x12 mm) | 100-TQFP - same | 100-TQFP - same | 100-TQFP - same | 100-TQFP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| CPU Performance | 70 MIPS (16-bit) | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS |
| Flash Memory | 128 KB (43K x 24) | 128 KB | 256 KB | 64 KB | 256 KB |
| Motor Control Peripherals | 12 MCPWM, 8 IC/8 OC, 2 QEI, 4 op-amps | Identical (same die) | Identical | Identical | Reduced - GM7 lacks full GM3 motor-control set |
| Operating Temperature | -40C to +85C (I) | -40C to +125C (E) | -40C to +85C | -40C to +85C | -40C to +85C |
| Packaging | Tape & Reel (T) | Tape & Reel | Tape & Reel | Tape & Reel | Tape & Reel |
关键差异点
- Integrated analog front-end （对比 DSPIC33EP256GM710T-I/PT)
- Extended-temperature drop-in option （对比 DSPIC33EP128GM310T-E/PT)
- Flash-size scalable single footprint （对比 DSPIC33EP64GM310T-I/PT / DSPIC33EP256GM310T-I/PT)
设计说明
Supply the DSPIC33EP128GM310T-I/PT from a clean 3.3V rail within the datasheet tolerance; place 0.1uF ceramic decoupling at each of the VDD/VSS pin pairs on the 100-TQFP plus one bulk 10uF capacitor near the corner supply pins. Separate the VDDCORE/VCAP requirements: the dsPIC33EP family requires an external low-ESR capacitor on the internal regulator output pin - check the datasheet pin table for the exact VCAP pin and use the recommended value, typically a 10uF low-ESR part, as omitting or undersizing it is a common cause of erratic startup.
The four on-chip op-amps and CTMU are only as accurate as their PCB environment. Route op-amp input traces short and guarded, keep them on an unbroken analog ground region, and never run MCPPWM outputs or gate-driver traces in parallel with analog feedback lines. For the dual QEI encoder inputs, use differential receivers if the encoder cable exceeds roughly 30 cm, and add series termination to control ringing at high count rates. Synchronize ADC sampling to PWM center or trough via the PTG or trigger chain to reject switching ripple in current loops.
Three frequent mistakes on dsPIC33EP designs: (1) Peripheral Pin Select (PPS) must be configured before peripherals using remappable pins function - a firmware that assumes fixed pinout will show dead UART or PWM pins; (2) the /T tape-and-reel part needs MSL-compliant reflow per the label rating - exceeding floor-life causes package moisture damage; (3) the /I rating tops out at +85C junction conditions per Microchip thermal data - if your enclosure runs hot near motor drives, migrate to the pin-identical DSPIC33EP128GM310T-E/PT rather than risking the temperature budget.
合规信息
Retrieved web data does not state formal RoHS/REACH declarations verbatim. Standard Microchip production parts are supplied lead-free; confirm formal certification via the Microchip environmental compliance portal for the specific date code before contractual use.
