DSPIC33FJ128GP708AT-I/PT - 16-bit 40 MIPS DSC 128KB Flash | Microchip
料号： DSPIC33FJ128GP708AT-I/PT ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $7.39 | $7.39 |
| 10 | $6.85 | $68.50 |
| 100 | $6.3 | $630.00 |
| 500 | $5.9 | $2,950.00 |
| 1,000 | $5.45 | $5,450.00 |
DSPIC33FJ128GP708AT-I/PT 概述
A Digital Signal Controller combines the compute power of a DSP core with the peripheral integration and ease of use of a microcontroller, occupying the middle of the embedded hierarchy: microcontroller -> DSC -> DSP. The dsPIC33F family executes DSP-class instructions such as single-cycle MAC and dual-field addressing while retaining familiar MCU peripherals, making it a bridge between general-purpose control and signal processing tasks.
Key features include a 16-bit dsPIC33F core running at up to 40 MIPS, on-chip Flash program memory of 128KB, DMA controllers for peripheral data transfer without CPU intervention, and a rich communications set: ECAN (Controller Area Network), I2C, SPI, UART, and I2S audio interfaces. Peripherals such as PWM outputs, AC'97 support, watchdog timer (WDT), power-on reset (POR), and undervoltage detection/reset round out the integration for mixed signal-and-control designs.
Architecturally, the dsPIC33F core is designed for digital filter algorithms, high-speed precision digital control loops, and digital audio and speech processing, per Microchip's family documentation. In-circuit debugging and In-Circuit Serial Programming (ICSP) are supported through MPLAB Snap and compatible tools, which use two device I/O pins and the reset line, streamlining development without dedicated socket programming.
Typical applications include digital power supplies and motor control loops exploiting the 40 MIPS core and PWM peripherals, industrial networking nodes using the ECAN module for CAN 2.0B connectivity, and audio/speech processing systems leveraging the I2S and DCI audio interfaces with DMA for low-latency streaming.
Design consideration: the 80-pin TQFP requires attention to power distribution - place 0.1 uF decoupling capacitors at every VDD/VSS pair and keep the ECAN transceiver routing away from the analog supply domain. Flash endurance and write-erase cycles should be budgeted if field reprogramming is planned.
This page synthesizes distributor pricing, drop-in family alternatives, design notes, and application guidance not consolidated in the manufacturer datasheet, with pricing verified as of 2026-09-26.
直接替换替代料： DSPIC33FJ128GP708AT-I/PT ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： DSPIC33FJ128GP708AT-I/PT （相同外形与封装尺寸） ——差异在于 Package, Operating Temperature, Program Memory Size, Packaging, Peripherals.
快速对比工具——选择替代料号进行并排对比：
DSPIC33FJ128GP708A-I/PT
✅ 直接替换✓ 有现货
$11.8 / 个
查看数据手册 →DSPIC33FJ128GP708T-I/PT
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$4.82 / 个
查看数据手册 →DSPIC33FJ256GP708AT-I/PT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
DSPIC33FJ64GP708AT-I/PT
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$6.3 / 个
查看数据手册 →DSPIC33FJ128GP808AT-I/PT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
DSPIC33FJ128GP310T-I/PT
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$5.46 / 个
查看数据手册 →DSPIC33FJ128GP708AT-I/PT 最大额定值与电气特性
| Core Processor | dsPIC33F (16-bit) |
| Core Size | 16-bit |
| Speed / Performance | 40 MIPS |
| Program Memory Size | 128KB (128K x 8) |
| Program Memory Type | Flash |
| 电源电压 | 3.3 V |
| Number of I/O | 69 |
| 封装 | 80-TQFP (12x12 mm) |
| 工作温度 | -40C to +85C (I grade) |
| Peripherals | AC'97, Brown-out Detect/Reset, DMA, I2S, POR, PWM, WDT |
| Communications Interfaces | ECAN, I2C, SPI, UART |
| 安装类型 | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Series | dsPIC 33F |
| Product Type | Digital Signal Controller (DSC) |
DSPIC33FJ128GP708AT-I/PT 80-tqfp (12x12 mm) 引脚配置指南
DSPIC33FJ128GP708AT-I/PT（80-tqfp (12x12 mm) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： DSPIC33FJ128GP708AT-I/PT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DSPIC33FJ128GP708AT-I/PT 适用于 6 应用s: Digital Power Supplies, Motor Control Drives, Industrial CAN Networking Nodes, Digital Audio and Speech Processing, Precision Sensor Acquisition Systems, Embedded Control with Field Updates.
Digital Power Supplies
The DSPIC33FJ128GP708AT-I/PT fits digital power conversion because its 16-bit core sustains 40 MIPS, enough to close current- and voltage-mode loops at switching frequencies of 100 kHz to several hundred kHz with single-cycle MAC instructions executing compensator math. The integrated PWM peripheral generates complementary or independent drive outputs with dead-time control, while DMA moves ADC results to RAM without CPU cycles, keeping ISR latency short and jitter low. Placed as the sole controller between the sensing front end and gate drivers, it eliminates analog compensator drift and enables adaptive startup and fault logging. The trade-off versus a dedicated analog controller is firmware development effort, repaid by field-updatable control laws in the 128KB Flash.
推荐
Motor Control Drives
For three-phase BLDC and PMSM drives, the DSPIC33FJ128GP708AT-I/PT provides the PWM peripheral for six-channel inverter gating with dead-time insertion, and its 40 MIPS core executes field-oriented control loops well within one PWM period. Sixty-nine I/O pins accommodate quadrature encoder inputs, hall sensors, gate-drive enable lines, and fault shutdown inputs on one 80-pin TQFP controller, reducing BOM count versus a discrete MCU plus DSP pair. DMA-serviced ADC sequences synchronize current sampling to PWM centers, minimizing switching-noise coupling. Microchip positions the dsPIC33F family explicitly for motor control; the practical consideration is budgeting Flash for sensorless observer algorithms, for which the 128KB array leaves ample headroom over basic trapezoidal control code.
推荐
Industrial CAN Networking Nodes
The on-chip ECAN module makes the DSPIC33FJ128GP708AT-I/PT a strong fit for CAN 2.0A/B industrial nodes such as sensor aggregators, actuator controllers, and J1939-style telemetry units. The 40 MIPS core filters and processes incoming frames in firmware while DMA streams payload data between the ECAN buffers and RAM, so the CPU stays available for application logic. Connect the CANTX/CANRX pins to a 3.3 V CAN transceiver at the network edge; 69 I/O remain available for local sensing and control. Compared with adding a standalone CAN controller over SPI, the integrated ECAN removes a bus-latency bottleneck and one PCB device. Confirm transceiver logic-level compatibility, since some legacy transceivers expect 5 V I/O.
推荐
Digital Audio and Speech Processing
Audio designs benefit from the DSPIC33FJ128GP708AT-I/PT's I2S and AC'97-capable data interface controller combined with DMA, which streams codec samples to and from RAM with deterministic latency while the 40 MIPS DSP core applies filters, AGC, echo cancellation, or sample-rate conversion using single-cycle multiply-accumulate instructions. As the host between a codec chip and amplifier front end, the DSC runs the full audio path digitally, avoiding the drift of analog equalization stages. The 128KB Flash holds typical speech-processing frameworks including boot code and coefficient tables. A key design consideration is clocking: derive the audio bit clock from the oscillator module with a crystal suited to standard 44.1/48 kHz families to avoid click artifacts from clock mismatch.
推荐
Precision Sensor Acquisition Systems
In multi-channel data acquisition, the DSPIC33FJ128GP708AT-I/PT pairs its on-chip ADC (with DMA-serviced scan sequences) against its SPI and I2C ports to aggregate external high-resolution converters while the 40 MIPS core applies calibration, linearization, and digital filtering locally. Placed at the head of a sensor module, it can timestamp, decimate, and packetize readings for UART or ECAN transmission without a separate protocol processor. The 69 I/O support channel-select multiplexers, relays, and status signaling, and brown-out plus watchdog peripherals guard data integrity in unattended industrial environments. For best accuracy, keep analog supply pins on a clean 3.3 V domain and sequence conversions away from PWM edges, which the DMA-trigger flexibility of the dsPIC33F family directly supports.
推荐
Embedded Control with Field Updates
Products requiring in-field firmware updates - charging stations, HVAC controllers, medical accessories - use the DSPIC33FJ128GP708AT-I/PT's self-programmable 128KB Flash to implement bootloaders, with ICSP (two I/O pins plus MCLR per Microchip's MPLAB Snap documentation) as the factory programming path. The 40 MIPS core leaves headroom to run application code and update verification concurrently, and the watchdog with brown-out protection prevents corrupted images from bricking units during power anomalies. Distribution over ECAN, UART, or SPI lets the same bootloader serve different product variants on one PCB. Plan Flash endurance into the maintenance schedule - frequent remote updates should use wear-levelled write patterns - and reserve a dual-image partition scheme in the 128KB array for safe rollback.
推荐
推荐产品汇总
工程参考数据： DSPIC33FJ128GP708AT-I/PT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DSPIC33FJ128GP708A-I/PT | DSPIC33FJ256GP708AT-I/PT | DSPIC33FJ64GP708AT-I/PT | DSPIC33FJ128GP808AT-I/PT | DSPIC33FJ128GP310T-I/PT |
|---|---|---|---|---|---|---|
| Package | 80-TQFP (12x12 mm) | 80-TQFP (12x12) - same | 80-TQFP (12x12) - same | 80-TQFP (12x12) - same | 80-TQFP (12x12) - same | 80-TQFP (12x12) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Performance | 16-bit, 40 MIPS | 16-bit, 40 MIPS | 16-bit, 40 MIPS | 16-bit, 40 MIPS | 16-bit, 40 MIPS | 16-bit, 40 MIPS |
| Program Memory (Flash) | 128KB (128K x 8) | 128KB | 256KB | 64KB | 128KB | 128KB |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Silicon Revision | A-step | A-step | A-step | A-step | A-step | A-step (310A available) |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
关键差异点
- Largest Flash in the drop-in group without PCB change （对比 DSPIC33FJ64GP708AT-I/PT)
- A-step silicon revision （对比 DSPIC33FJ128GP708T-I/PT)
- Cost-optimized versus Flash-doubling upgrade （对比 DSPIC33FJ256GP708AT-I/PT)
设计说明
The 80-TQFP (12x12 mm) exposes multiple VDD/VSS pin pairs; place a 0.1 uF ceramic decoupling capacitor at every pair, as close to the pins as possible, plus one bulk 4.7-10 uF capacitor near the supply entry. Keep the ECAN transceiver and oscillator traces short and away from the analog pins used for sensing. The 0.5 mm lead pitch requires soldermask-defined pads per the Microchip layout guidelines in the datasheet package outline section; verify your fab capability for 0.5 mm pitch QFP assembly before releasing the footprint.
The device runs from a 3.3 V rail with internal brown-out and POR supervision. When sharing the 3.3 V rail with 5 V-derived systems, add a regulator with adequate startup ramp to satisfy the dsPIC33F power-up requirements, and hold MCLR low via an RC network (typical 10 kohm / 0.1 uF) to guarantee a clean reset. Estimated: with 40 MIPS operation the core current is typically in the tens-of-milliamps range - size the regulator for the full 69-I/O load plus 30% margin, and confirm exact figures in the datasheet electrical characteristics tables.
Do not confuse the A-step and non-A silicon revisions (DSPIC33FJ128GP708AT vs non-A suffixes): Microchip publishes family-specific errata that differ between revisions, so verify code behavior if swapping. When using ECAN, remember that most CAN transceivers are 5 V devices - a level-tolerant transceiver or level shifting is required. Also, ICSP consumes two I/O pins and MCLR; avoid dedicating those pins to critical functions, or provide isolation so a connected programmer does not load your circuit during development.
合规信息
Compliance status not stated in the provided web data; verify on the Microchip product page environmental datasheet. The 'I' temperature grade denotes -40C to +85C industrial operation; AEC-Q100 qualification is not claimed for this part.
