ICS411MLF - 25MHz PC Peripheral Clock | Renesas Electronics
料号: ICS411MLF ✗ 停产ICS411MLF 概述
A peripheral clock synthesizer is a type of clock and timing integrated circuit that generates or conditions a stable reference signal for digital subsystems. Clock generators and clock buffers sit within the broader clock-and-timing hierarchy, which supports synchronization, data transfer, and deterministic circuit operation in personal computers, communications equipment, and embedded systems. The ICS411MLF converts a system timing reference into the clock required by compatible PC peripheral functions.
Key characteristics include a nominal output frequency of 25 MHz, a 3 V to 3.6 V operating supply range, and an 8-SOIC package compatible with standard surface-mount assembly. Its single-function architecture allows a motherboard or peripheral design to obtain a defined clock without implementing a general-purpose programmable oscillator. The 8-pin package also keeps the required PCB footprint compact while providing separate supply and clock-related connections.
The ICS411MLF is intended for applications where a conventional, fixed-frequency clock source is sufficient and the design priority is component-count reduction. Its fixed 25 MHz output simplifies schematic design because the required frequency does not need to be programmed or adjusted during operation. The manufacturer describes the device as a cost-effective clock synthesizer for PC motherboard and peripheral applications, making it most appropriate for established platform architectures rather than new designs requiring programmable frequency, spread-spectrum modulation, or fractional-N synthesis.
Typical uses include PC motherboard peripheral clock distribution, storage-controller clocking, interface-module clocking, and legacy peripheral systems operating from a 3.3 V rail. In these designs, the synthesizer supplies a common local reference while system-level oscillators or phase-locked loops establish the master timing hierarchy. Power-system design must still account for the device's 3 V to 3.6 V operating range and verify the output behavior against the load and trace requirements of the connected peripheral.
The principal design consideration is compatibility with the target clock tree. Confirm the required frequency, supply voltage, output-load expectations, and board-level timing budget in the manufacturer datasheet before layout release. Route the clock output as a short, controlled-impedance trace and keep the supply return path close to the device so that the fixed 25 MHz reference reaches the load without unnecessary added noise or timing distortion.
This page organizes the manufacturer and distributor information for the ICS411MLF into an engineering-oriented product record. It combines the 25 MHz clock function, supply range, 8-SOIC packaging, purchasing guidance, and design considerations so that engineers can evaluate the device quickly against motherboard and peripheral clock requirements.
直接替换替代料: ICS411MLF ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料ICS411MLF 规格参数
| Manufacturer | Renesas Electronics |
| 功能 | PC peripheral clock synthesizer |
| Output Frequency | 25 MHz |
| Supply Voltage Range | 3 V to 3.6 V |
| Device Type | Clock synthesizer / frequency generator |
| 封装 | 8-SOIC, 0.154 inch body width, 3.90 mm width |
| 安装类型 | Surface mount |
| Packaging | Tube |
| Operating Class | PC peripheral clock |
| Design Objective | Reduce component count in PC motherboard and peripheral applications |
ICS411MLF 8-soic, 0.154 inch body width, 3.90 mm width 引脚配置指南
ICS411MLF(8-soic, 0.154 inch body width, 3.90 mm width 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ICS411MLF.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ICS411MLF 适用于 6 应用s: PC Motherboard Peripheral Clocking, Storage Controller Clock Reference, Interface Module Clocking, Peripheral Adapter Reference Clock, Legacy Digital Subsystem Timing, Instrumentation and Test Support Clock.
PC Motherboard Peripheral Clocking
The ICS411MLF suits a legacy or established PC motherboard that needs a dedicated 25 MHz peripheral reference without a programmable oscillator. Its 3 V to 3.6 V operating range aligns with a 3.3 V system rail, while the 8-SOIC package minimizes board area. Place the device near the receiving peripheral logic, connect the bypass capacitor at the supply pins, and route the output as a short trace. Because this is a fixed-frequency clock, the design should verify that 25 MHz is the exact local reference required and that the output amplitude satisfies the receiver's threshold specifications.
Storage Controller Clock Reference
A storage-controller subsystem can use the ICS411MLF as a local 25 MHz reference when the controller requires a dedicated peripheral clock and the system already provides the appropriate reference input. The fixed output avoids programming overhead and reduces the number of timing components compared with a programmable clock generator. The designer must confirm the controller's permitted frequency tolerance, clock amplitude, and duty-cycle expectations in its documentation, then keep the ICS411MLF supply and ground connections close to the device to minimize supply-induced clock disturbance.
Interface Module Clocking
The ICS411MLF can support a compact interface module requiring a common 25 MHz peripheral clock on a 3.3 V rail. Its eight-pin SOIC package is convenient for conventional reflow assembly and keeps routing straightforward. Use a controlled-impedance clock trace, avoid adding test-point stubs that create unwanted reflections, and provide a nearby supply bypass capacitor. This application is best for fixed-frequency legacy interfaces; a programmable clock generator is a better choice when the module needs selectable rates, multiple derived outputs, or software-controlled clock management.
Peripheral Adapter Reference Clock
An add-in or external peripheral adapter may require a local 25 MHz clock where the host interface does not distribute a suitable reference to that subsystem. The ICS411MLF provides a compact fixed-frequency solution in an 8-SOIC package and operates from 3 V to 3.6 V. Confirm the adapter's timing budget and clock-input specification before layout, since tolerance and phase requirements determine whether the synthesized reference is acceptable. Keep the output path short and isolate the clock trace from switching-node edges where possible.
Legacy Digital Subsystem Timing
The ICS411MLF fits established digital subsystems that expect a 25 MHz clock and operate from a 3.3 V rail, particularly where a cost-focused design goal is to minimize the component count of the clock tree. Its fixed output means no firmware configuration is necessary, which simplifies validation for a stable platform. Nevertheless, the receiving logic must be checked for minimum input pulse width, duty-cycle limits, setup and hold requirements, and a valid clock edge definition before the part is approved for production.
Instrumentation and Test Support Clock
The ICS411MLF can act as a simple 25 MHz reference in older test, measurement, or data-acquisition hardware that expects a conventional peripheral clock. The 8-SOIC package is easy to place on a densely populated analog or mixed-signal board, and the 3 V to 3.6 V range supports 3.3 V instrumentation. When the clock drives precision converters or counters, validate the edge quality and output level against those components, and keep high-energy analog and switching traces spatially separated from the clock output.
工程参考数据: ICS411MLF ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Brand | Renesas Electronics |
| Package | 8-SOIC |
| Function | PC peripheral clock synthesizer |
| Output Frequency | 25 MHz |
| Supply Voltage Range | 3 V to 3.6 V |
| Frequency Control | Fixed |
| Mounting Type | Surface mount |
| Packaging | Tube |
| Primary Application | PC motherboard and peripheral clocking |
关键差异点
- Fixed-frequency implementation reduces clock-tree complexity (对比 Programmable 25 MHz clock-generator alternatives)
- Compact eight-pin implementation for conventional PCB assembly (对比 Larger clock-generator packages)
- Direct fit for nominal 3.3 V PC peripheral rails (对比 Clock generators limited to narrower supply ranges)
设计说明
Place the ICS411MLF close to the circuit that receives its 25 MHz output, and route the clock net as a short, controlled-impedance trace. Avoid long stubs or unnecessary test points that can create reflections on this clock edge. Keep the device supply bypass capacitor immediately adjacent to the supply and ground pins, with a short ground return, to reduce supply-induced clock disturbance.
Confirm the receiver's minimum clock amplitude, duty-cycle limits, input pulse-width requirement, and setup or hold timing against the manufacturer datasheet. A nominal 25 MHz match is not sufficient for a drop-in decision because clock thresholds and edge quality determine whether the receiver samples the reference reliably. Preserve a continuous ground path beneath the device and avoid crossing the clock trace with high-current switching paths.
Do not treat the ICS411MLF as a programmable clock generator or assume that any 25 MHz oscillator is interchangeable. Verify the 3 V to 3.6 V supply range, reference-input arrangement, output-load capability, and eight-pin SOIC pin functions before substitution. Also confirm whether the board requires tube packaging or an alternate shipping format when placing a production order.
合规信息
No definitive RoHS, REACH, halogen-free, or conflict-minerals statement was identified in the available manufacturer and distributor records. AEC-Q100 qualification is not applicable to this PC peripheral clock device.