ICS501MT - 160MHz PLL Clock Generator | Renesas | SOIC-8
料号: ICS501MT ✓ 量产中ICS501MT 概述
A programmable clock generator is an integrated timing device that converts a lower-frequency reference into a stable higher-frequency output. Clock generators and phase-locked loops occupy the Clock & Timing category within integrated circuits, supporting digital processing, communications, control, and data-conversion systems. The ICS501 LOCO family uses phase-locked-loop techniques to multiply a fundamental-mode crystal reference and is positioned as a cost-effective alternative to conventional crystal-oscillator arrangements in many electronic systems.
The ICS501MT combines a maximum frequency of 160MHz with a CMOS output and a 1:1 multiplication ratio. Its input can be a clock or crystal, allowing it to serve systems that already have a timing reference or need a PLL-based clock output. The single-circuit arrangement simplifies designs requiring one output, while the surface-mount 8-SOIC package supports conventional PCB assembly and compact equipment layouts.
At its core, the device uses PLL technology to generate a high-quality clock from a lower-frequency reference. This architecture is useful when a system needs a frequency above the practical range of a simple resonator-based oscillator without adopting a more elaborate frequency synthesizer. The documented 1:1 ratio indicates that the principal output relationship corresponds directly to the selected input and crystal configuration; system designers should consult the Renesas 501 datasheet for the exact supported input-frequency and output-frequency ranges.
Typical uses include digital logic systems, embedded control equipment, communications interfaces, and test or measurement instruments requiring a distributed CMOS clock. The ICS501MT can provide a common local clock where a stable reference is available but multiple distributed logic sections need synchronized operation. Its maximum 160MHz output frequency also makes it suitable for clocking architectures operating below that upper limit.
PCB implementation requires close attention to the recommended crystal or clock-input network, output routing, grounding, and decoupling. Keep the timing network and the device’s output path short, maintain a continuous ground reference, and follow the manufacturer’s layout guidance to minimize jitter and edge degradation. Confirm all timing, voltage, load, and stability limits against the complete Renesas 501 datasheet before release.
This product page combines verified device characteristics, practical clocking guidance, a pin-compatible replacement assessment, and parameter-level comparisons. It is intended to accelerate engineering review while preserving the distinction between confirmed specifications and parameters that require confirmation from the full manufacturer documentation.
直接替换替代料: ICS501MT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
501MLFT
✅ 直接替换📋 参考替代料(不在目录中)
501MLF
✅ 直接替换📋 参考替代料(不在目录中)
ICS501MT 规格参数
| Product Type | 1 clock generator |
| PLL | Yes |
| Input Type | Clock or crystal |
| 输出类型 | CMOS |
| Maximum Output Frequency | 160 MHz |
| Number of Circuits | 1 circuit |
| Input-to-Output Ratio | 1:1 |
| Differential Input | No |
| Differential Output | No |
| 封装 | 8-SOIC (0.154 inch, 3.90mm width) |
| 安装类型 | Surface mount |
| 引脚数 | 8 pins |
| RoHS 状态 | Non-compliant |
ICS501MT 8-soic (0.154 inch, 3.90mm width) 引脚配置指南
ICS501MT(8-soic (0.154 inch, 3.90mm width) 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ICS501MT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ICS501MT 适用于 6 应用s: Digital Logic Clock Distribution, Communications Equipment Timing, Embedded Control and Processor Timing, Data Acquisition and Conversion Clocks, Test and Measurement Instrumentation, Industrial Control Module Timing.
Digital Logic Clock Distribution
The ICS501MT is suitable for generating a common CMOS timing reference in digital logic systems operating below the device's 160MHz maximum output frequency. Place the regulator in the timing-isolation or clock-generation section of the board, provide the recommended crystal or clock input network, and distribute the single output to local logic through short, properly terminated routes. The documented 1:1 input-to-output ratio supports designs where the PLL configuration preserves the selected reference relationship. Because edge rate, jitter, load capability, and allowable frequency ranges are not summarized in the available product information, engineers should verify those limits in the Renesas 501 datasheet before fixing propagation-delay and timing budgets.
推荐
Communications Equipment Timing
The ICS501MT can support communications equipment that needs a stable local CMOS clock derived from a crystal or external clock reference. Its PLL architecture allows a lower-frequency fundamental reference to support a high-quality generated output, while the 160MHz maximum frequency covers many interface and digital-control clocking requirements. In a communications board, keep the oscillator away from switching-converter power loops and high-speed data regions, because return-current coupling can degrade edge timing. Confirm differential-clock requirements before selection: the ICS501MT is listed as a single-ended CMOS device with no differential input or output, so it is appropriate only where the subsystem accepts single-ended timing.
推荐
Embedded Control and Processor Timing
The ICS501MT can provide a dedicated clock source for embedded controllers, programmable logic, and mixed-signal subsystems that require a stable reference independent of another timing component. Its 1:1 ratio and single output are straightforward for designs where one CMOS clock domain serves the processor, serial interface, or data converter. Keep the crystal and feedback network close to the device, connect decoupling according to the manufacturer layout, and maintain a low-impedance return path beneath the clock route. The key design check is the required operating frequency and available jitter margin, neither of which should be inferred solely from the 160MHz headline specification; verify both in the complete Renesas documentation.
推荐
Data Acquisition and Conversion Clocks
The ICS501MT is applicable to data-acquisition and analog-to-digital or digital-to-analog conversion systems that require a local single-ended CMOS sampling clock. Generating the clock close to the converter can shorten the timing path and reduce susceptibility to board-level noise compared with routing a reference across a larger assembly. Establish the complete timing budget before implementation, including converter acquisition requirements, clock duty cycle, jitter tolerance, and source-to-converter propagation delay. The ICS501MT's single-circuit output is a good fit when only one synchronized clock is needed; a multi-clock instrument should confirm whether a separate distributor or additional clock-generation component is required.
推荐
Test and Measurement Instrumentation
The ICS501MT can serve as the local timing element in test and measurement instruments that generate, process, or digitize signals from a stable crystal reference. The PLL-based architecture is useful when a common reference must be regenerated locally, and the 160MHz maximum output provides headroom for many digital acquisition and control paths. For sensitive analog measurements, isolate the oscillator's return current from sensitive signal-ground regions and use a controlled ground-plane strategy rather than splitting the ground plane unnecessarily. Confirm output rise time, jitter, duty cycle, and load drive from the Renesas 501 datasheet because these parameters directly influence timing accuracy and measurement uncertainty.
推荐
Industrial Control Module Timing
The ICS501MT can provide a compact clock source for industrial control modules that coordinate sensors, actuators, communication interfaces, and digital logic. Its surface-mount 8-SOIC package fits conventional control-board assembly, while the crystal-or-clock input allows use of an existing reference where available. In an industrial environment, keep the timing network away from high-current switching nodes and route the clock over a continuous reference plane. The design must verify the exact supply-voltage range, operating-temperature grade, frequency window, and output-load limits in the official 501 documentation; those constraints are more important than the 160MHz maximum when selecting the device for long-duration industrial operation.
推荐
推荐产品汇总
工程参考数据: ICS501MT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | 501MLFT | 501MLF |
|---|---|---|---|
| Package | 8-SOIC (0.154 inch, 3.90mm width) | 8-SOIC (0.154 inch, 3.90mm width) | 8-SOIC (0.154 inch, 3.90mm width) |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Product Type | Clock Generator IC | Clock Generator | Clock Generator |
| Maximum Frequency | 160 MHz | 160 MHz | 160 MHz |
| PLL | Yes | Yes | Yes |
| Input | Clock or Crystal | Clock or Crystal | Clock or Crystal |
| Output | CMOS | CMOS | CMOS |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
| Input-to-Output Ratio | 1:1 | 1:1 | 1:1 |
| Differential Input and Output | No / No | No / No | No / No |
关键差异点
- Direct same-family replacement path (对比 501MLFT)
- Single-ended clock output (对比 501MLF)
- PLL-based frequency generation (对比 501MLFT)
设计说明
Place the ICS501MT, crystal, and associated load components as a compact timing block close to the point of use. Route the output over a continuous ground reference and avoid branches, test pads, or unnecessary vias that add capacitive loading. Confirm the pin assignments and land pattern in the Renesas 501 datasheet before layout release.
Use the manufacturer-recommended crystal and input network rather than copying a generic oscillator connection. Keep high-impedance timing nodes short, provide the specified supply and ground decoupling, and maintain a low-impedance return path from the output driver. These layout controls reduce edge distortion, coupling, and startup sensitivity.
Validate the clock at the far end of its route with an appropriate high-impedance probe because long traces, capacitive loading, and stubs can alter edge rate and duty cycle. Check the receiver's threshold, trace impedance, and available timing margin, and use series termination only when the edge characteristics and load require it.
Do not assume that every 501 ordering suffix is automatically acceptable for the same product qualification. The 501MLFT and 501MLF are identified as direct SOIC-8 replacements, but voltage, frequency window, temperature grade, packing, lifecycle status, and production qualification must still be checked against the official 501 datasheet.
合规信息
A component listing identifies the ICS501MT as RoHS non-compliant. No authoritative REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification declaration was identified.