INA117SMQ - High Common-Mode Differential Amplifier | Texas Instruments
料号: INA117SMQ ✓ 量产中INA117SMQ 概述
A difference amplifier is a specialized analog signal-conditioning IC that subtracts two input voltages and amplifies the difference by a fixed gain. In the precision unity-gain configuration used by the INA117 family, the common-mode signal is rejected by the matched resistor network rather than being amplified. This places the INA117 hierarchy within precision difference amplifiers, instrumentation signal-conditioning circuits, analog amplifiers, and the broader semiconductor category.
Key features include a ±200 V common-mode input range, unity differential gain, and a 200 kHz bandwidth. The high common-mode capability allows the amplifier to operate on battery, industrial, automotive, or power-system voltages without requiring the inputs to remain close to ground. The monolithic thin-film network also provides stable matching between the input resistors, which improves common-mode rejection and repeatability compared with discrete resistor networks.
Technically, the INA117 is designed for accurate differential measurement rather than high-speed signal processing. Its 200 kHz bandwidth supports measurements in power-conversion, motor-control, battery-monitoring, and industrial-control systems, but it is not intended for video-frequency amplification. Input protection is especially important because the common-mode rating describes the intended signal range and does not replace correct supply, absolute-maximum, and transient-voltage analysis.
Typical applications include high-side current sensing, power-supply current monitoring, battery-pack measurement, motor-control feedback, and high-voltage instrumentation. Designers commonly place the device between a sensing resistor and an analog-to-digital converter so that a small differential voltage can be measured while a much larger common-mode voltage is rejected.
The primary design consideration is protecting the input stage from transients and exceeding the device's absolute-maximum ratings. Keep input routing short, use suitable input attenuation or clamping networks, and reference the output carefully for single-supply operation. Stable operation also depends on maintaining the specified supply voltage and avoiding excessive input impedance asymmetry at the two inputs.
This product page combines the INA117 family specifications with practical guidance on high-common-mode sensing, package considerations, input protection, and qualified drop-in alternatives. It is intended to help engineers identify whether the TO-99 packaged INA117SMQ fits a high-voltage measurement design and what parameters must be checked before substitution.
直接替换替代料: INA117SMQ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: INA117SMQ (相同外形与封装尺寸) ——差异在于 Package, Mounting Type, Product Type, Number of Channels, Operating Temperature Range.
INA117SM
✅ 直接替换联系询价
查看数据手册 →INA149AIPG
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
INA117SMQ 最大额定值与电气特性
| Product Type | Precision unity-gain difference amplifier |
| Common-Mode Input Voltage Range | -200 V to +200 V |
| Differential Gain | 1 V/V unity gain |
| Bandwidth | 200 kHz |
| Number of Channels | 1 channel |
| 引脚数 | 8 pins |
| 封装 | TO-99-8 metal can |
| 安装类型 | Through-hole |
| 工作温度范围 | -40°C to +85°C |
| Resistor Network | Integrated thin-film resistor network |
| Internal Amplifier | Single precision operational amplifier |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | unknown |
| Lead-Free Status | unknown |
INA117SMQ to-99-8 metal can 引脚配置指南
INA117SMQ(to-99-8 metal can 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: INA117SMQ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
INA117SMQ 适用于 6 应用s: High-Side Power Current Sensing, Battery-Pack Monitoring, Motor-Control Feedback, Industrial Power-Line Monitoring, Power-Supply Feedback, Precision High-Voltage Instrumentation.
High-Side Power Current Sensing
The INA117SMQ fits high-side current measurement because it can tolerate a common-mode input range of ±200 V while responding to the small differential voltage produced by a shunt. Place the shunt terminals on the two amplifier inputs and use the amplifier output as the scaled shunt voltage. This arrangement prevents the large load voltage from being amplified directly. Before implementation, verify the transient profile, shunt excitation, and output swing against the Texas Instruments electrical characteristics.
推荐
Battery-Pack Monitoring
INA117SMQ can measure a low-level differential battery-monitor signal when the common pack voltage falls within its ±200 V range. The integrated thin-film resistor network and unity-gain architecture are useful when both sensor inputs share a substantial common-mode voltage. The amplifier should sit close to the sensing element to limit noise pickup, while surge and load-dump protection remain external design functions. Verify operating temperature, supply voltage, and the converter interface used to digitize the output.
推荐
Motor-Control Feedback
The INA117SMQ is appropriate for low-bandwidth motor-control feedback signals that combine a small differential measurement with a larger switching-node voltage. Its 200 kHz bandwidth can represent control-loop information without targeting video-bandwidth amplification. Place the device near the current or position sensor, maintain symmetrical input routing, and confirm that motor-switching transients do not exceed the input limits. The exact response requirement should be compared with the device's offset, noise, and bandwidth characteristics.
推荐
Industrial Power-Line Monitoring
INA117SMQ supports industrial monitoring circuits that must distinguish a small voltage across a power conductor from a much larger line potential. The ±200 V common-mode range is useful in systems below that boundary, while the precision unity-gain structure avoids the resistor mismatch found in discrete difference stages. Use input clamping for switching and fault transients, and reference the output appropriately for the selected supply arrangement. Confirm isolation, safety, and protection requirements separately from signal conditioning.
推荐
Power-Supply Feedback
The INA117SMQ can condition feedback from a high-side current or voltage-sense element in a power-conversion system. Its unity differential gain preserves the measured difference while the integrated thin-film network suppresses the common component. This is useful when the converter node rises well above signal-ground level. Select the supply rails to support the required output range, decouple the amplifier close to its pins, and verify that switching overshoot remains within the device's allowable input and supply conditions.
推荐
Precision High-Voltage Instrumentation
INA117SMQ is suited to instrumentation that measures low-level differential signals superimposed on voltages approaching the ±200 V common-mode boundary. The monolithic thin-film network provides matched resistance within the device, supporting repeatable difference measurements. Input impedance, offset, and CMRR determine how much error appears at the output, so the source impedances should remain close and balanced. For signals outside the rating, select a higher-range amplifier or redesign the front end with attenuation and isolation.
推荐
推荐产品汇总
工程参考数据: INA117SMQ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | INA117SM | INA149AIPG | INA149 |
|---|---|---|---|---|
| Package | TO-99-8 | TO-99-8 | TO-99-8 | TO-99-8 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Pin Count | 8 pins | 8 pins | 8 pins | 8 pins |
关键差异点
- Precision differential measurement with a high common-mode boundary (对比 INA149AIPG)
- Direct same-family ordering alternative in the original metal-can package (对比 INA117SM)
- Integrated matched thin-film network (对比 INA149)
设计说明
Treat the ±200 V common-mode rating as an operating range, not as permission to expose the inputs to arbitrary transients. Review the absolute-maximum input voltage and supply limits in the Texas Instruments datasheet, then add series resistance, clamps, or other protection appropriate to the source. A protection network must preserve differential accuracy while limiting surge current into the amplifier.
Route the two difference inputs as a closely coupled pair and keep them away from switching nodes and high-current paths. Match source impedances where practical because unequal impedances can unbalance the integrated network and degrade common-mode rejection. Place the device near the sensing element, minimize input-loop area, and provide local supply bypassing according to the manufacturer application circuit.
The 200 kHz bandwidth is appropriate for power-measurement and industrial-control loops but limits rapid transient capture. If the input waveform contains significant energy above that bandwidth, the amplifier may introduce phase delay or attenuation in the control loop. Evaluate the complete signal chain against the required loop bandwidth and use a higher-bandwidth amplifier when waveform fidelity is more important than high common-mode tolerance.
Do not assume that a common TO-99 outline guarantees a drop-in substitution. Compare pin numbers, reference connection, supply range, gain accuracy, offset voltage, CMRR, bandwidth, and absolute-maximum ratings. The INA117SM and INA149 family options are relevant starting points, but each must satisfy the complete signal-chain requirements before schematic and layout reuse is approved.
合规信息
Compliance declarations and qualification details are not stated on the product pages listed for this part. Confirm the current manufacturer declarations and project-specific qualification requirements before release.