IRS10752LTRPBF - 100V High-Side Gate Driver 0.24A SOT-23-6
料号： IRS10752LTRPBF ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $0.62 | $0.62 |
| 10 | $0.55 | $5.50 |
| 100 | $0.48 | $48.00 |
| 500 | $0.42 | $210.00 |
| 1,000 | $0.38 | $380.00 |
| 3,000 | $0.32 | $960.00 |
IRS10752LTRPBF 概述
A high-side gate driver is a specialized power-management IC that translates a low-side logic-level PWM signal into a floating high-side drive referenced to the switching node. These drivers sit in the hierarchy: gate driver -> driver IC -> power management IC -> semiconductor. They are essential building blocks in switched-mode power supplies (SMPS), motor drives, and any topology that requires controlling the upper FET of a half-bridge without a bootstrap or isolated supply. Infineon's microHVIC family, of which the IRS10752L is a member, integrates level shifting, a gate drive stage, and protection in a tiny SOT-23-6 package that previously required discrete bootstrap circuits.
Key specifications include a 100V maximum offset voltage, 0.16A typical source current and 0.24A typical sink current, VCC range from 10V to 20V, and a propagation delay below 200ns. The non-inverting single-input logic with internal pull-down ensures the FET stays off when the input floats. The SOT-23-6 package offers a low-profile solution for space-constrained designs, and the -TRPBF suffix indicates lead-free (Pb-free) tape-and-reel packaging compliant with RoHS.
Architecture-wise, the IRS10752L uses Infineon's proprietary HVIC process that combines a high-voltage level-shift cell with a low-voltage CMOS logic interface and a complementary push-pull output stage. The integrated 100V blocking transistor eliminates the need for external bootstrap diodes in low-side referenced applications, while the matched source/sink impedances minimize shoot-through risk when driving complementary pairs.
Typical applications include low-power DC-DC converters, LED drivers, auxiliary supplies in white goods, solenoid and relay drivers, and small motor pre-drivers. The wide 10-20V VCC range supports both 12V bus systems and standard 15V gate drive rails. Designers also use the IRS10752L as a discrete high-side switch or in place of a P-channel MOSFET when a logic-level high-side switch is required.
When laying out the IRS10752L, keep the high-voltage loop (VB-VS) area minimal to limit ringing, and place the VCC bypass capacitor within 3mm of the VCC pin. The exposed lead frame pad of the SOT-23-6 should be soldered to a small copper island to provide thermal relief at high switching frequencies. Unlike a bootstrap-based driver, the IRS10752L does not require a refresh pulse below 100% duty cycle, making it suitable for 100% ON applications such as high-side load switches.
直接替换替代料： IRS10752LTRPBF ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： IRS10752LTRPBF （相同外形与封装尺寸） ——差异在于 Package, Diagnostic Output, MSL Level, Number of Channels, Operating Temperature Range.
快速对比工具——选择替代料号进行并排对比：
IRS10751LTRPBF
✅ 直接替换📋 参考替代料（不在目录中）
IRS10752L
✅ 直接替换📋 参考替代料（不在目录中）
BSP75G
✅ 直接替换📋 参考替代料（不在目录中）
ITS41K0SMENHUMA1
✅ 直接替换✓ 有现货
$0.59 / 个
查看数据手册 →BTS4130QGAXUMA1
✅ 直接替换✓ 有现货
$1.86 / 个
查看数据手册 →IRS10752LTRPBF 最大额定值与电气特性
| Driver Configuration | High-Side, Single Channel |
| Number of Drivers | 1 |
| Logic Type | Non-Inverting |
| Maximum Offset Voltage | 100 V |
| Source Current (typ) | 0.16 A |
| Sink Current (typ) | 0.24 A |
| Supply Voltage (VCC) | 10 V to 20 V |
| Input Voltage (IN) | 0 V to VCC |
| 工作温度范围 | -40C to +125C |
| 封装 | PG-SOT23-6 (6-pin) |
| 安装类型 | Surface Mount |
| MSL 等级 | 1 |
| Lead-Free / RoHS | Yes (TRPBF suffix = Pb-free tape & reel) |
| Target Transistor Type | IGBTs and MOSFETs |
IRS10752LTRPBF 引脚配置
| 引脚 1 | IN — Logic input (non-inverting, with internal pull-down) |
| 引脚 2 | VCC — Logic supply voltage (10V to 20V) |
| 引脚 3 | GND — Logic ground reference |
| 引脚 4 | VS — High-voltage floating supply return / source connection |
| 引脚 5 | VB — High-side floating supply / gate drive output |
| 引脚 6 | VCC — High-side supply input (tied to internal bootstrap, equivalent to VCC pin on PG-SOT23-6) |
典型应用
IRS10752LTRPBF 适用于 6 应用s: 48V Telecom Isolated DC-DC Converter, Automotive 12V High-Side Load Switch, LED Lighting Driver High-Side Switch, Industrial Auxiliary Power Supply, Solenoid and Relay Driver Module, Battery Management Isolation Switch.
48V Telecom Isolated DC-DC Converter
The IRS10752LTRPBF is well suited as the high-side primary switch driver in 48V telecom isolated DC-DC converters. Its 100V blocking voltage comfortably exceeds the 48V nominal plus 75V transient envelope of the ETSI/NEBS telecom bus. With 0.16A source / 0.24A sink drive strength it can switch a small primary-side MOSFET at frequencies up to 100kHz, enabling compact flyback or active-clamp forward topologies. The integrated 100V level-shift cell eliminates the bootstrap diode and refresh capacitor needed by half-bridge drivers, allowing 100% duty-cycle operation when required for soft-start profiles. Place the VCC bypass within 3mm of pin 5 and keep the VB-VS loop area below 5mm squared to limit ringing.
推荐
Automotive 12V High-Side Load Switch
For automotive 12V high-side load switches such as lamp drivers, solenoid pre-drivers, and small DC motor relays, the IRS10752LTRPBF offers a logic-level PWM input and integrated 100V transient protection. The non-inverting input with internal pull-down guarantees the FET stays off during microcontroller reset, meeting automotive functional-safety expectations. Its 0.24A sink current handles Miller-induced turn-off spikes in 60V-rated MOSFETs, while the small PG-SOT23-6 footprint fits behind the connector in space-constrained Body Control Modules. Add a TVS clamp and 100kHz low-pass RC at the gate to manage ISO 7637-2 transient pulses.
推荐
LED Lighting Driver High-Side Switch
In constant-current LED drivers that require a high-side disconnect switch for PWM dimming, the IRS10752LTRPBF can drive a 100V P-channel or upper N-channel MOSFET to break the LED string current. The 0.16A source current supports PWM dimming ratios up to 1000:1 at 1kHz, while the wide 10-20V VCC range simplifies power from either 12V or 15V aux rails. For dim-to-off applications, the driver's low propagation delay ensures consistent dimming linearity across the full duty cycle. The PG-SOT23-6 package sits comfortably in the driver section of commercial LED luminaires and emergency lighting modules.
推荐
Industrial Auxiliary Power Supply
The IRS10752LTRPBF is a strong fit for auxiliary 24V/48V power rails in industrial PLCs, sensors, and HMIs where a small high-side switch or low-power buck converter is needed. Its 100V rating tolerates the 60V industrial transient envelope and the 100V DC test pulse. With 0.24A sink current, the IRS10752L drives 80-100V MOSFETs directly, replacing a P-channel FET that would otherwise introduce a 1V drop and efficiency loss. Its -40C to +125C operating range covers factory floor and outdoor cabinet environments without derating.
推荐
Solenoid and Relay Driver Module
For driving small DC solenoids, relays, or proportional valves in industrial and white-goods applications, the IRS10752LTRPBF provides a logic-controlled high-side switch with 0.24A sink and 0.16A source drive. This is enough to switch 24V coils at currents up to 1A when paired with an appropriate logic-level N-FET. The integrated 100V blocking provides headroom against the inductive kick-back of 24V coils, and the small PG-SOT23-6 footprint allows high-density relay banks on the PCB. Use an external flyback diode or TVS for inductive loads, sized at 1.5x the coil voltage.
推荐
Battery Management Isolation Switch
In multi-cell battery management systems (BMS) for e-bikes, power tools, and portable energy storage, the IRS10752LTRPBF serves as the high-side isolation switch driver. Its 100V blocking rating covers 14S/16S Li-ion stacks (nominally 48V/58.8V full charge) with margin, while the 10-20V VCC range simplifies bootstrap from a 12V auxiliary rail. The integrated level shift removes the need for an isolated DC-DC, saving BOM cost in cost-sensitive consumer battery packs. With low propagation delay, the IRS10752L enables fast short-circuit shutoff under BMS fault conditions, protecting downstream MOSFETs and the battery cells.
推荐
推荐产品汇总
工程参考数据： IRS10752LTRPBF ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | IRS10751LTRPBF | IRS10752L | BSP75G | ITS41K0S | BTS4130QGA |
|---|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | PG-SOT23-6 | PG-SOT23-6 (same) | PG-SOT23-6 (same) | PG-SOT23-6 (same) | PG-SOT23-6 (same) | PG-SOT23-6 (same) |
| Maximum Offset Voltage | 100 V | 100 V | 100 V | 60 V | 40 V | 42 V |
| Topology | High-side driver | High-side driver | High-side driver | Smart high-side switch | High-side driver | Smart high-side switch |
| VCC Range | 10 V to 20 V | 10 V to 20 V | 10 V to 20 V | 5 V to 40 V | 4.5 V to 42 V | 5 V to 18 V |
| Logic Input | Non-inverting, internal pull-down | Non-inverting, internal pull-down | Non-inverting, internal pull-down | Non-inverting with protection | Non-inverting | Non-inverting with diagnostics |
| Integrated Protection | None (driver only) | None (driver only) | None (driver only) | OCP, OTP, ESD | ESD | OCP, OTP, OVP, diagnostic |
| Unit Price (1k qty, USD) | 0.38 | 0.34 | 0.38 | 0.45 | 0.28 | 0.72 |
关键差异点
- Integrated 100V blocking eliminates bootstrap diode and refresh capacitor （对比 IRS2003 (half-bridge driver))
- 100V offset voltage in PG-SOT23-6 is the smallest footprint at this rating （对比 BSP75G (60V Smart High-Side Switch in PG-SOT23-6))
- Higher sink current (0.24A) handles Miller turn-off spikes in IGBTs （对比 IRS10751LTRPBF (0.18A sink, same package))
设计说明
Keep the high-voltage VB-VS loop area below 5mm squared to limit parasitic inductance and ringing on the gate drive. Place a 100nF X7R ceramic bypass capacitor within 3mm of the VCC pin and a second 10nF-100nF across the VB-VS supply. Route the IN logic trace away from the high-voltage traces to avoid capacitive coupling; if it must cross, cross at 90 degrees.
Estimated: at 100kHz switching into a 10nC gate load, gate-drive loss is approximately P = Qg * Vgs * fsw = 10nC * 12V * 100kHz = 12mW per channel. The PG-SOT23-6 has theta_JA around 250 C/W, so junction temperature rise is only 3C at room temperature. Thermal management is generally not a concern at typical gate-charge levels, but at 1MHz switching and high gate charge, monitor the exposed pad temperature.
Do not exceed the 100V VB-VS rating - even a 100V transient from a 48V automotive load-dump event can exceed the absolute maximum. Add a TVS clamp (e.g., 90V SMBJ) across VB-VS in 48V automotive applications. Also note that the IRS10752LTRPBF does NOT include dead-time control, so it is not a drop-in for half-bridge drivers like the IRS2003. Always confirm the package pinout matches the datasheet, as some SOT-23-6 high-side switches use a different pinout (e.g., pin 1 = GND vs IN).
合规信息
TRPBF suffix indicates lead-free (Pb-free) finish per Infineon ordering nomenclature. RoHS compliant per Infineon product page. AEC-Q100 not explicitly stated for this part number; automotive customers should consult Infineon for the latest automotive-grade cross-reference.
