ISL81483IB - 5V 250kbps RS-485/RS-422 Transceiver | Renesas
料号: ISL81483IB ✓ 量产中ISL81483IB 概述
An RS-485 transceiver is an interface IC that converts between logic-level signals and differential bus signals. RS-422 supports point-to-point, point-to-multipoint, and multidrop topologies, while RS-485 allows longer cables, broader node counts, and noise-resistant differential signaling. The ISL81483 belongs to the broader hierarchy of interface transceiver, communications interface, and semiconductor devices used to connect embedded controllers to field buses.
Key characteristics include 1/8-unit-load bus loading, 5V operation, a maximum data rate of 250kbps, and support for both RS-485 and RS-422 networks. The reduced receiver loading permits more equipment on the same bus than a conventional one-unit-load receiver. The manufacturer documents low-power operation and options for high-speed or slew-rate-limited operation, allowing the interface strategy to be selected according to channel length, topology, and electromagnetic compatibility requirements.
The ISL81483 and ISL81487 family combines a differential driver, differential receiver, and transmit/receive control in a compact 8-pin SOIC. Reduced unit load lowers the effective bus impedance presented by each node, which can help preserve signal amplitude and operating margin in long or highly populated networks. Designers must still account for termination, biasing, common-mode limits, and grounding according to the application circuit in the Renesas datasheet.
Typical uses include process-automation networks, remote utility meter reading, industrial sensor gateways, building-control equipment, and remote instrumentation. In a utility-meter network, multiple apartment or building meters can route readings through an RS-485 segment toward a concentrator. The 256-node capability shown by the 1/8-unit-load architecture is particularly useful when field equipment must remain operational at low bus voltage.
The primary design consideration is selecting the correct edge rate and bus topology. High-speed operation maximizes throughput but can increase reflected and radiated signal effects on long cables, while slew-rate limiting can reduce EMI at the cost of maximum data rate. Place the device near the bus connector, provide a solid ground reference, follow recommended termination practices, and validate signal integrity across cable lengths and environmental conditions.
This product page combines the Renesas family description with practical bus-design guidance, package details, sourcing information, and a parameter-focused comparison of true pin-compatible alternatives. It helps engineers identify the correct transceiver role, assess node-count and data-rate constraints, and determine whether a direct replacement preserves the existing 8-pin SOIC PCB footprint.
直接替换替代料: ISL81483IB ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ISL81483IB (相同外形与封装尺寸) ——差异在于 Maximum Data Rate, Package, Product Type, RoHS Status.
ISL8487EIBZ-T
✅ 直接替换📋 参考替代料(不在目录中)
ISL81487
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
ISL81483IB 规格参数
| Product Type | Half-duplex RS-485/RS-422 transceiver |
| 电源电压 | 5 V |
| Maximum Data Rate | 250 kbps |
| Receiver Unit Load | 1/8 unit load |
| Maximum Bus Node Count | 256 transceivers |
| Supported Standards | RS-485 and RS-422 |
| Duplex Mode | Half-duplex |
| Driver Configuration | 1/1 |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
| Operating Mode Options | High-speed or slew-rate-limited |
| Power Classification | Low power |
| Lead-Free Status | Lead free |
| RoHS 状态 | Non-compliant |
| Application: Process Automation | Supported for large-node-count process automation networks |
| Application: Remote Meter Reading | Supported for remote utility meter reading systems |
ISL81483IB 8-pin soic 引脚配置指南
ISL81483IB(8-pin soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ISL81483IB.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ISL81483IB 适用于 6 应用s: Remote Utility Meter Reading, Process Automation Field Bus, Industrial Sensor Gateway, Building Control Network, Remote Instrumentation, Data Acquisition Terminal.
Remote Utility Meter Reading
The ISL81483IB is well suited to remote utility meter-reading networks that gather readings from many distributed endpoints and route them toward a concentrator. Its 5V operating supply fits embedded metering electronics, while the 1/8-unit-load receiver architecture permits as many as 256 transceivers on one RS-485 segment. The 250kbps maximum data rate supports efficient polling of meters, sensors, and endpoint identification data. Designers should use differential bus routing, appropriate termination, and a biasing strategy suited to the deployed cable length and node population.
推荐
Process Automation Field Bus
Process-automation installations commonly connect many remote sensors, actuators, and controllers over a common differential bus. The ISL81483IB reduces each receiver's loading to 1/8 unit, allowing a node count of up to 256 and preserving operating margin in larger systems. Its RS-485 and RS-422 support, 250kbps capability, and selectable high-speed or slew-rate-limited behavior make it useful for factory-floor communications where both network density and predictable signal behavior matter.
推荐
Industrial Sensor Gateway
An industrial sensor gateway can use the ISL81483IB to bridge a local controller to an RS-485 network of distributed sensing nodes. The 1/8-unit load supports a larger population of compact remote sensors than a conventional one-unit-load receiver, while the 250kbps rate accommodates periodic measurement traffic and configuration commands. The 8-pin SOIC format keeps the interface compact, and slew-rate-limited operation can help control edge-related EMI in installations containing long cables or nearby sensitive equipment.
推荐
Building Control Network
The ISL81483IB can connect building-control equipment such as distributed room sensors, dampers, lighting controllers, and HVAC interfaces through an RS-485 backbone. Its low 1/8-unit receiver loading is valuable in buildings with numerous nodes and short branch cabling, while 250kbps is more than adequate for supervisory control traffic. Slow or slew-rate-limited signaling may be preferable on older or extended building wiring, subject to cable-length and timing validation.
推荐
Remote Instrumentation
Remote laboratory and industrial instrumentation systems benefit from the ISL81483IB when many measurement instruments must share a two-wire differential bus. The reduced 1/8-unit load allows higher node density, and the device's support for both RS-485 and RS-422 gives designers flexibility in point-to-point and multidrop arrangements. At rates up to 250kbps, the interface can carry command, status, and measurement traffic, while proper grounding and termination remain essential for reliable operation.
推荐
Data Acquisition Terminal
The ISL81483IB is appropriate for distributed data-acquisition terminals that forward sensor readings to a central controller over RS-485. The 1/8-unit receiver loading enables a larger group of remote acquisition modules, and the 5V supply can simplify integration with low-voltage embedded electronics. A data rate of up to 250kbps is useful for periodic sample batches and device commands. For each terminal, validate driver enable timing, bus-idle behavior, termination, and protection against industrial transients.
推荐
推荐产品汇总
工程参考数据: ISL81483IB ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ISL8487EIBZ-T | ISL81487 |
|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Product Type | Half-duplex RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver |
| Supported Standards | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
关键差异点
- High node-count capability (对比 ISL8487EIBZ-T)
- Documented communication-speed ceiling (对比 ISL81487)
- Dual RS-485 and RS-422 support (对比 ISL8487EIBZ-T)
设计说明
Route the differential A and B connections as a closely matched pair on the PCB, minimize stubs, and keep the transceiver interface section physically close to the bus connector. Provide a low-impedance ground reference and follow the manufacturer application circuit for termination and protection placement. The 8-pin SOIC package leaves limited room for optional networks, so establish the resistor values and protection strategy before finalizing placement.
Choose high-speed or slew-rate-limited operation according to channel length and electromagnetic compatibility requirements. The ISL81483 supports up to 250kbps, but faster edge rates can increase ringing and radiated emissions on long or unterminated cables. Validate the intended node count, cable type, termination, and bias arrangement in hardware, and ensure the receiver remains enabled only when the bus is actively driven.
Do not assume that every 8-pin RS-485 transceiver has identical enable and receiver-control polarity. Check the ISL81483IB terminal assignments and logic levels in the Renesas datasheet before connecting the microcontroller. Also avoid leaving the driver continuously enabled on a multidrop bus, because multiple drivers can contend when their output states differ and prevent reliable communication.
合规信息
The product listing identifies the device as lead free and RoHS non-compliant. No qualifying automotive qualification, REACH declaration, halogen-free declaration, or conflict-minerals statement is available for this orderable variant.