ISL84051IA - 8:1 100 Ohm Analog Multiplexer | Renesas
料号: ISL84051IA ✗ 停产ISL84051IA 概述
An analog multiplexer is a semiconductor switch that routes multiple input signals to one common output. It belongs to the analog switch and multiplexer hierarchy, where a multiplexer reduces the number of external connections needed by a data-acquisition system. The ISL84051IA combines an 8-to-1 signal configuration, selectable signal polarity, and an inhibit function within a compact surface-mount package.
Principal features include an 8-to-1 configuration, 100-ohm maximum on-resistance as listed by distributors, TTL/CMOS-compatible logic inputs, and operation from 2 V to 12 V. The device can also operate from dual supplies, making it suitable for systems that must route signals centered around ground. Its low-voltage design supports analog measurement, test, and signal-routing equipment.
The ISL84051 family is designed as a pin-compatible replacement for MAX4051 and MAX4051A devices. Control logic determines which one of the eight analog inputs connects to the common output, while the inhibit pin can disconnect all signal paths. This architecture reduces input-channel count on analog-to-digital converter boards and permits several sensors or voltage sources to share one conversion channel.
Typical uses include battery-cell measurement, automated test equipment, data-acquisition systems, sample-and-hold networks, and general-purpose analog routing. Designers should account for on-resistance when calculating signal attenuation, confirm that the selected supply configuration meets the input voltage range, and treat the inhibit function as a deliberate control signal rather than a substitute for power sequencing.
PCB placement should keep analog traces short and provide a nearby ground return to minimize parasitic pickup. Input and output protection may be required when connected to external sources. The manufacturer datasheet should guide logic-level compatibility, supply sequencing, and handling of unused channels.
This page combines device specifications, verified drop-in cross-references, application guidance, and package-specific selection information to support faster engineering evaluation and sourcing decisions.
直接替换替代料: ISL84051IA ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MAX4051
✅ 直接替换📋 参考替代料(不在目录中)
MAX4051A
✅ 直接替换📋 参考替代料(不在目录中)
ISL84051IA 最大额定值与电气特性
| Configuration | 8-to-1 analog multiplexer |
| Number of Circuits | 1 circuit |
| Maximum On-Resistance | 100 ohm |
| On-Resistance at ±5 V | 60 ohm |
| Single-Supply Voltage Range | 2 V to 12 V |
| Supply Configuration | Single or dual supply |
| Logic Compatibility | TTL/CMOS compatible |
| Signal Path Count | 8 inputs to 1 output |
| Inhibit Function | All signal paths can be opened |
| 封装 | 16-QSOP |
| 安装类型 | Surface mount |
| Pb-Free Identification | Pb-free device |
| Manufacturer Compatibility | Pin compatible with MAX4051 and MAX4051A |
ISL84051IA 16-qsop 引脚配置指南
ISL84051IA(16-qsop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ISL84051IA.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ISL84051IA 适用于 6 应用s: Battery Cell Multiplexing, Automated Test Equipment, Data Acquisition Systems, Sensor Signal Routing, Sample-and-Hold Systems, Portable Measurement Instruments.
Battery Cell Multiplexing
The ISL84051IA is well suited to low-voltage battery-cell measurement because its 8-to-1 architecture allows eight monitored sources to share one analog measurement channel while operating from a supply range that extends down to 2 V. Place the selected cell signal on the common output and connect the remaining inputs to the cells being monitored. The 100-ohm maximum on-resistance must be included in the measurement-source impedance budget, while the inhibit function can isolate the path during reset or calibration. The selected ADC should also tolerate switching transients and leakage from the multiplexer.
推荐
Automated Test Equipment
The ISL84051IA can route one of eight test signals to a shared measurement instrument, reducing the number of analog input connections in automated test equipment. Its TTL/CMOS-compatible control inputs support conventional digital control logic, and the 16-QSOP package conserves board area. The 100-ohm maximum on-resistance can affect high-impedance measurements, so the instrument input and source network should be checked together. Use the inhibit function to isolate the selected path during fixture reset, calibration, or a safety-related transition.
推荐
Data Acquisition Systems
An ISL84051IA-based data-acquisition front end can use one converter input for eight analog channels, simplifying connector density and PCB routing. The low-voltage operation supports embedded measurement systems, while dual-supply capability permits signals centered around ground. Account for the listed 100-ohm maximum on-resistance when calculating source impedance and acquisition time. Keep the common output and selected inputs away from fast digital clocks, provide a continuous ground reference, and confirm that leakage and switching transients fall within the converter’s acquisition requirements.
推荐
Sensor Signal Routing
The ISL84051IA can select among eight sensor outputs for a common conditioning or conversion stage, reducing duplicated front-end circuitry in compact sensing systems. Low-voltage operation is useful when the sensors operate near the lower end of the supported 2 V to 12 V range. The analog switch resistance should remain small relative to the sensor and amplifier input impedances to avoid gain errors. Place the device close to the multiplexer or conditioning amplifier, maintain short return paths, and use the inhibit control when a sensor must be disconnected during system initialization.
推荐
Sample-and-Hold Systems
The ISL84051IA can route one of eight rapidly changing inputs into a shared sample-and-hold stage, making it useful when a system requires source selection before a single hold capacitor. The 8-to-1 topology prevents each source from requiring a separate hold path. Designers should verify settling behavior against the resistance of the sampling network, the selected signal amplitude, and the multiplexer’s on-resistance. The inhibit function provides a clean way to open the path while the hold network is reset, helping avoid unintended charge transfer between measurement phases.
推荐
Portable Measurement Instruments
The ISL84051IA suits portable measurement instruments that need to switch among several low-voltage inputs without multiplying connector pins. Its 16-QSOP package supports compact layouts, and operation down to 2 V fits battery-powered systems. The multiplexer’s 100-ohm maximum on-resistance can become significant when measuring high-impedance sensors, so buffer or compensate the selected source as appropriate. Keep the analog path away from wireless or switching-converter traces, provide local grounding, and use the inhibit input to establish a defined state during startup and shutdown.
推荐
推荐产品汇总
工程参考数据: ISL84051IA ——对比、设计指导和合规信息。
选型指南
Choose the MAX4051 when maintaining an existing MAX-family design and qualifying that established alternative is preferable to changing the component manufacturer. Choose the MAX4051A for a board tied specifically to that enhanced MAX-family variant, after checking its detailed electrical limits and package ordering code. Both MAX devices are documented as pin-compatible drop-in relationships for the ISL84051 function, but supply limits, leakage, switching timing, temperature grade, and availability must be checked for the exact ordering option before releasing a substitution to production.
与替代料对比
| 参数 | 本产品 | MAX4051 | MAX4051A |
|---|---|---|---|
| Multiplexer Configuration | 8-to-1 | 8-to-1 | 8-to-1 |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
| Package | 16-QSOP | 16-QSOP | 16-QSOP |
| Brand | Renesas Electronics | Maxim Integrated | Maxim Integrated |
| Drop-In Relationship | Replaces MAX4051 and MAX4051A | Pin-compatible MAX-family equivalent | Pin-compatible MAX-family equivalent |
关键差异点
- Direct documented relationship with the MAX4051 family (对比 MAX4051)
- Defined 16-QSOP implementation (对比 MAX4051)
- Low-voltage single- and dual-supply operation (对比 MAX4051A)
设计说明
Include the switch’s on-resistance when calculating the Thevenin source impedance seen by the following converter or amplifier. The distributor listing specifies a 100-ohm maximum, while another technical summary identifies 60 ohms at ±5 V. For high-impedance sensors, verify the actual resistance curve at the operating supply and signal level; if the resulting divider error is excessive, place a low-input-impedance buffer after the multiplexer.
Place the 16-QSOP close to the analog source connector and the receiving converter or amplifier. Keep the common output and all eight input routes short, provide a continuous ground reference, and avoid routing these traces beneath digital clocks, display signals, or switching-regulator nodes. This arrangement reduces parasitic pickup and makes the 100-ohm switch resistance less significant relative to the complete analog path.
Do not treat the inhibit input as a substitute for removing power or for managing an overvoltage condition. Use it to open the signal paths during reset, calibration, or controlled isolation. Confirm the logic polarity and timing from the manufacturer datasheet, and ensure that every unused analog input is connected to a defined potential. Floating inputs can introduce coupling into measurements even when the selected channel is inactive.
合规信息
The available comparison information identifies ISL84051IA as a Pb-free device. Explicit RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals declarations are not stated.