KSZ8842-PMBL-AM - 2-Port 10/100 Ethernet Switch | Microchip
料号: KSZ8842-PMBL-AM ✓ 量产中KSZ8842-PMBL-AM 概述
An Ethernet switch is a semiconductor that connects multiple Ethernet nodes while using Layer 2 media-access-control addresses to forward frames. The KSZ8842 belongs to the broader network-interface hierarchy: Ethernet controller, network interface IC, interface IC, and integrated circuit. It integrates two Fast Ethernet PHYs and switch functions, reducing the need for separate Ethernet controllers or physical-layer devices in compact embedded equipment.
The KSZ8842-PMBL-AM is based on Microchip's fourth-generation integrated Layer 2 switch architecture. Key features include two managed 10/100 ports, a 32-bit PCI interface operating at 33 MHz, IEEE 802.3u compliance, and an industrial-temperature-grade ordering option. Its small 100-LFBGA package supports space-constrained PCI host systems while exposing the complete two-port switching function on one device.
The PCI host interface provides a direct path for a processor or embedded controller to configure the switch, exchange packet data, and access switch management registers. This integration is particularly useful when an embedded system needs two Ethernet ports but has limited board area or component count. Exact register behavior, interrupt architecture, and management features should be confirmed from the manufacturer's KSZ8842-PMQL/PMBL datasheet before final software configuration.
Typical uses include industrial control systems, embedded routers, automated test equipment, POS terminals, and PCI-based communication appliances. In these applications, the two integrated Fast Ethernet ports can support a local equipment network, uplink, or network segmentation. The industrial-temperature designation makes the PMBL-AM version more appropriate for extended-temperature equipment than the standard PMBL ordering option.
PCB implementation requires careful review of the 100-LFBGA land pattern, power and ground distribution, clock requirements, and high-speed signal routing. The 9 x 9 mm package is not a leaded package, so assembly capability, solder-mask definition, stencil aperture design, and via-in-pad or thermal-via requirements must be coordinated with the board manufacturer before release.
This product analysis consolidates the manufacturer architecture description, package information, ordering distinctions, replacement considerations, and PCB implementation guidance into an engineering-focused resource for evaluating the KSZ8842-PMBL-AM in compact embedded Ethernet systems.
直接替换替代料: KSZ8842-PMBL-AM ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: KSZ8842-PMBL-AM (相同外形与封装尺寸) ——差异在于 Ethernet Speed, Host Interface, Product Type.
KSZ8842-PMBL
✅ 直接替换联系询价
查看数据手册 →KSZ8842-PMBL-AM 最大额定值与电气特性
| Product Type | Managed 2-port Layer 2 Ethernet switch |
| Number of Ethernet Ports | 2 ports |
| Ethernet Speed | 10/100 Base-T/TX |
| Host Interface | 32-bit PCI |
| PCI Interface Clock | 33 MHz |
| Network Standard | IEEE 802.3u |
| Switch Architecture | Fourth-generation integrated Layer 2 switch |
| Temperature Grade | Industrial |
| 封装 | 100-LFBGA, 9 x 9 mm |
| 安装类型 | Surface mount |
| 引脚数量 | 100 pins |
| Managed Switch Ports | 2 ports |
| Physical Layer Functions | Integrated 10/100 Base-T/TX PHYs |
KSZ8842-PMBL-AM 100-lfbga, 9 x 9 mm 引脚配置指南
KSZ8842-PMBL-AM(100-lfbga, 9 x 9 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: KSZ8842-PMBL-AM.
请参阅 数据手册 以查看完整引脚配置。
典型应用
KSZ8842-PMBL-AM 适用于 6 应用s: Embedded PCI Router, Industrial Control Gateway, Automated Test Equipment, Point-of-Sale Terminal, Embedded Communication Appliance, PCI Network Segmentation Controller.
Embedded PCI Router
The KSZ8842-PMBL-AM fits an embedded router that connects a host processor to two managed 10/100 Base-T/TX ports. Its 32-bit, 33 MHz PCI interface provides a direct host path for packet exchange and switch configuration, while the integrated Layer 2 engine reduces the need for separate Ethernet switch silicon. The 100-LFBGA, 9 x 9 mm package also supports compact embedded boards, although Ethernet magnetics, isolation, and connector implementation remain required.
推荐
Industrial Control Gateway
The KSZ8842-PMBL-AM is appropriate for an industrial control gateway requiring two managed Fast Ethernet connections and an industrial-temperature ordering option. The host processor can access both ports through the 32-bit, 33 MHz PCI interface, reducing component count compared with a separate Ethernet controller and switch combination. Design teams should use the manufacturer reference circuit for magnetics, termination, supply routing, and PCI signal layout.
推荐
Automated Test Equipment
A PCI-based automated test system can use the KSZ8842-PMBL-AM to provide two managed 10/100 network connections without adding a separate two-port switch. The 32-bit PCI host interface allows equipment firmware to exchange test data and monitor switching status through the device registers. Its 100-LFBGA package is small but requires assembly-process validation, controlled BGA layout, and careful separation between PCI, clock, and Ethernet-related routing.
推荐
Point-of-Sale Terminal
The KSZ8842-PMBL-AM can serve a PCI point-of-sale terminal that needs separate network ports for a primary connection and local peripheral link. Two managed 10/100 ports provide Layer 2 switching in one device, while the PCI interface connects the network function to the host processor. The compact 9 x 9 mm LFBGA helps minimize board area, but power integrity, Ethernet magnetics, chassis grounding, and production stencil testing remain essential.
推荐
Embedded Communication Appliance
The KSZ8842-PMBL-AM is suitable for compact communication appliances that expose two managed Fast Ethernet ports through a PCI host bus. Integrating the PHYs and Layer 2 switch supports a simpler hardware architecture than a discrete controller-plus-switch design. Firmware should use the manufacturer register definitions for port configuration, status, interrupts, and address-table operation, while the PCB follows the reference layout for the 100-LFBGA device.
推荐
PCI Network Segmentation Controller
The KSZ8842-PMBL-AM can implement a dedicated Layer 2 segmentation point between a PCI host and two 10/100 network segments. Its fully managed switch architecture allows host software to configure forwarding behavior through the PCI interface. The device is well suited to fixed-function embedded equipment where predictable wired connectivity is needed, but production designs should verify register behavior, reset requirements, clock topology, and thermal performance under sustained traffic.
推荐
推荐产品汇总
工程参考数据: KSZ8842-PMBL-AM ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | KSZ8842-PMBL |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 100-LFBGA (9x9) | 100-LFBGA (9x9) |
| Ethernet Ports | 2 ports | 2 ports |
| Ethernet Speed | 10/100 Base-T/TX | 10/100 Base-T/TX |
| Host Interface | 32-bit PCI at 33 MHz | 32-bit PCI at 33 MHz |
| Temperature Grade | Industrial | Standard grade |
| Network Standard | IEEE 802.3u | IEEE 802.3u |
| Switch Architecture | Fully managed fourth-generation Layer 2 switch | Fully managed fourth-generation Layer 2 switch |
关键差异点
- Industrial-temperature ordering option (对比 KSZ8842-PMBL)
- Two managed Fast Ethernet ports in one device (对比 KSZ8842-PMBL)
- Compact PCI network integration (对比 KSZ8842-PMBL)
设计说明
Use the Microchip 100-LFBGA land pattern and assembly recommendations without modifying ball locations or adding unofficial via-in-pad features. Review the package drawing, solder-mask opening, stencil thickness, and assembly house capabilities together. The package has 100 contacts in a 9 x 9 mm footprint, so registration and coplanarity errors can affect both the PCI and Ethernet-related connections.
Route the 32-bit PCI interface as a controlled-length, impedance-controlled group and keep it separated from Ethernet magnetics and switching regulators. Follow the manufacturer reference layout for clock routing, decoupling, ground partitioning, and via placement. Place input and bulk capacitors near their associated supply pins and preserve a low-impedance return path beneath high-speed interfaces.
Confirm the device supply limits, current consumption, sequencing requirements, and power-supply tolerances from the Microchip datasheet before finalizing the rail design. Decouple each required supply with the capacitance and ESR characteristics specified by the manufacturer. Avoid deriving regulator sizing solely from nominal current because Ethernet magnetics, the host interface, and transient conditions can change the system power profile.
Do not substitute the PMQL package for PMBL without changing the PCB land pattern, and do not treat the AM suffix as a temperature-range specification by itself. Confirm the complete ordering code, package, temperature grade, and reel configuration. After PCB assembly, validate PCI enumeration, both Ethernet ports, reset behavior, and the intended Layer 2 configuration before deploying the equipment.
合规信息
The industrial-temperature ordering option does not by itself establish AEC-Q100 qualification. Compliance declarations should be confirmed against the current Microchip product documentation for the exact ordering code.