Microchip Technology

LAN8700C-AEZG-AR2 - 10/100 Ethernet PHY | Microchip | Automotive

料号: LAN8700C-AEZG-AR2 ✓ 量产中
1.6 V to 3.6 V Vdss 36-QFN (6 mm × 6 mm) Package
最小起订量: 1 |

LAN8700C-AEZG-AR2 概述

Microchip Technology LAN8700C-AEZG-AR2 is a low-power 10/100 Mb/s Ethernet physical-layer transceiver with full MII and RMII host interfaces, HP Auto-MDIX support, and variable I/O voltage operation. The device is supplied in a 36-pin QFN package with an exposed pad, measuring 6 mm by 6 mm, for compact embedded Ethernet designs.

An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts logical data supplied by a host controller into signals suitable for twisted-pair Ethernet cabling. It belongs to the transceiver and interface-IC hierarchy within network semiconductor solutions. This LAN8700 variant is intended for automotive and industrial embedded systems where low-power operation, compact packaging, cable flexibility, and robust transient protection are important design considerations.

Key characteristics include support for 10 Mb/s and 100 Mb/s operation, full MII and RMII controller interfaces, HP Auto-MDIX support, and ±15 kV ESD-protected cable-side connections. The variable I/O voltage architecture allows the digital interface voltage to be selected independently of the analog PHY supply, simplifying integration with host processors operating at different logic levels. The automotive AR2 ordering option supports design environments requiring an extended automotive qualification profile.

The LAN8700 architecture combines an analog 10/100 Ethernet front end with digital data-path logic and an integrated 1.6 V to 3.6 V low-power core. Its exposed thermal pad provides a direct heat-transfer path from the IC into the PCB. The 6 mm × 6 mm QFN-36 footprint also requires careful escape routing for its MII or RMII signals, clock inputs, power rails, and magnetics-side connections.

Typical uses include automotive infotainment controllers, industrial Ethernet gateways, embedded Linux platforms, set-top equipment, and compact communications modules. The MII interface provides a parallel data path for higher host clock rates, while RMII reduces pin count and board-routing pressure in designs where the host controller supports it. Auto-MDIX simplifies installation by allowing the PHY to handle straight-through or crossover cable connections automatically.

Designers should follow the manufacturer datasheet for the exposed-pad land pattern, decoupling, magnetic-component selection, cable termination, and separation between analog and digital circuitry. This page combines package, interface, protection, and application information with replacement guidance and engineering-focused design notes to support PCB and firmware implementation.

直接替换替代料: LAN8700C-AEZG-AR2 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: LAN8700C-AEZG-AR2 (相同外形与封装尺寸) ——差异在于 Host Interface, Package.

Microchip Technology
Host Interface: MII and RMII
Package: 36-QFN, 6 x 6 mm
对比 LAN8700C-AEZG-AR2 →

LAN8700C-AEZG

✅ 直接替换
📦 36-QFN (6 mm × 6 mm)
Same 10/100 Ethernet PHY, MII/RMII interfaces, and 36-QFN footprint; ordering grade differs from the automotive AR2 version

📋 参考替代料(不在目录中)

LAN8700IC-AEZG

✅ 直接替换
📦 36-QFN (6 mm × 6 mm)
Same 10/100 Ethernet PHY family and AEZG 36-QFN footprint; ordering-temperature or qualification option differs

📋 参考替代料(不在目录中)

LAN8700C-AEZG-AR2 规格参数

Ethernet Data Rate 10 Mb/s or 100 Mb/s
Host Interface Full MII and RMII
Auto-MDIX HP Auto-MDIX supported
ESD Protection ±15 kV
Core Supply Voltage Range 1.6 V to 3.6 V
Variable I/O Voltage Supported
封装 36-QFN (6 mm × 6 mm)
Exposed Thermal Pad Present
安装类型 Surface mount
Qualification Profile Automotive
Product Family LAN8700
PHY Type Single-channel 10/100 Ethernet transceiver
Technology flexPWR
Cable Support 10/100BASE-T twisted-pair Ethernet
Duplex Operation Full-duplex

LAN8700C-AEZG-AR2 36-qfn (6 mm × 6 mm) 引脚配置指南

LAN8700C-AEZG-AR2(36-qfn (6 mm × 6 mm) 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

LAN8700C-AEZG-AR2 的 36-qfn (6 mm × 6 mm) 封装引脚图

暂无详细引脚数据: LAN8700C-AEZG-AR2.

请参阅 数据手册 以查看完整引脚配置。

典型应用

LAN8700C-AEZG-AR2 适用于 6 应用s: Automotive Infotainment Ethernet, Industrial Ethernet Gateway, Embedded Linux Communication Module, Automotive Telematics Unit, Set-Top Box and Media Terminal, Robotics and Sensor Network Node.

🚗

Automotive Infotainment Ethernet

The LAN8700C-AEZG-AR2 fits compact automotive infotainment and connectivity modules that require a 10/100 Mb/s Ethernet link to a host processor. Its full MII interface supports a parallel host data path, while RMII can reduce connection count when the controller supports that mode. The 36-QFN (6 mm × 6 mm) package preserves board area, and ±15 kV cable-side ESD protection adds a useful layer of ruggedness. Auto-MDIX also simplifies installation by supporting straight-through and crossover cables. The exposed pad should be connected to the PCB thermal plane using the manufacturer’s recommended via pattern.

🏭

Industrial Ethernet Gateway

The LAN8700C-AEZG-AR2 can provide the physical layer for an industrial gateway connecting an embedded controller to a 10/100BASE-T network. Its low-power 1.6 V to 3.6 V core operation and variable I/O voltage simplify integration with processors using a different logic voltage. HP Auto-MDIX reduces installation complexity in field equipment, while the MII option supports host clocks commonly used by industrial controllers. The 36-QFN exposed-pad package requires careful thermal-pad layout and controlled copper connectivity for reliable heat transfer.

🌐

Embedded Linux Communication Module

The LAN8700C-AEZG-AR2 is appropriate for compact embedded Linux communication modules that require reliable 10/100 Mb/s Ethernet connectivity. RMII reduces the number of host connections and board-routing requirements, while full MII remains available when the host interface timing requires it. Auto-MDIX improves deployment flexibility, and the ±15 kV ESD rating supports protection around the external cable interface. The designer should isolate the analog and digital supplies, keep the exposed pad thermally connected, and follow the reference layout for magnetics-side components.

🚗

Automotive Telematics Unit

The LAN8700C-AEZG-AR2 suits automotive telematics and vehicle-network gateway equipment requiring a compact 10/100 Ethernet physical layer. The AR2 automotive ordering profile is a key reason to prefer this exact suffix over a generic industrial grade, while HP Auto-MDIX simplifies connection to service equipment and external network hardware. Full MII offers a wide parallel interface for compatible controllers, whereas RMII can simplify wiring in space-constrained nodes. Transient protection is especially relevant where cables leave the protected enclosure.

📺

Set-Top Box and Media Terminal

The LAN8700C-AEZG-AR2 provides a compact Ethernet front end for set-top boxes, media terminals, and residential equipment requiring 10/100 Mb/s connectivity. Its variable I/O voltage supports integration with host logic that does not use the PHY core voltage directly, while Auto-MDIX removes manual polarity checks during installation. The QFN-36 footprint reduces board area compared with larger transceivers, but its dense escape routing requires careful component placement. Adequate decoupling and a continuous exposed-pad thermal connection are essential for reliable operation.

🤖

Robotics and Sensor Network Node

The LAN8700C-AEZG-AR2 can serve as the Ethernet physical layer in a compact robot controller or distributed sensor node that needs 10/100 Mb/s connectivity. RMII is useful when the host controller already includes that interface, reducing wiring and routing overhead in a crowded control board. HP Auto-MDIX helps technicians connect nodes without manually configuring crossover cables, and ESD-protected cable connections support field-installed equipment. The exposed pad should be tied to a low-impedance thermal plane, and magnetics-side traces should be kept away from sensitive signal paths.

What is the LAN8700C-AEZG-AR2?
The LAN8700C-AEZG-AR2 is a Microchip Technology single-channel 10/100 Mb/s Ethernet physical-layer transceiver with full MII and RMII host interfaces. According to the Microchip LAN8700/LAN8700i data sheet, it provides HP Auto-MDIX support, variable I/O voltage operation, flexPWR technology, and ±15 kV ESD protection. It is packaged for automotive embedded-Ethernet designs in a 36-pin QFN package with an exposed pad.
What Ethernet speeds does LAN8700C-AEZG-AR2 support?
The LAN8700C-AEZG-AR2 supports both 10 Mb/s and 100 Mb/s Ethernet operation. According to the Microchip LAN8700/LAN8700i data sheet, it is a 10/100BASE-T physical-layer transceiver for twisted-pair Ethernet and supports full-duplex communication. The host connection is available through full MII or RMII, allowing the PHY to be paired with host controllers that use either interface style.
Which package does LAN8700C-AEZG-AR2 use?
The LAN8700C-AEZG-AR2 uses a 36-QFN package measuring 6 mm × 6 mm and includes an exposed thermal pad. Distributor and manufacturer listings identify the package as 36-QFN (6 × 6). Because an exact 36-pin QFN drawing is not included in the package-diagram library, use the manufacturer land-pattern and pin-description tables when assigning PCB tracks and thermal-pad vias.
Where can I download the LAN8700C-AEZG-AR2 datasheet PDF?
The manufacturer data sheet is available from Microchip at https://ww1.microchip.com/downloads/en/DeviceDoc/00002260A.pdf. It covers the LAN8700 and LAN8700i family, including the MII/RMII interfaces, HP Auto-MDIX operation, flexPWR low-power features, ESD characteristics, electrical limits, and application information. Use its ordering-information section to confirm how the automotive AR2 suffix relates to the base LAN8700C device.
Where can I find the LAN8700C-AEZG-AR2 pinout?
The LAN8700C-AEZG-AR2 pinout is documented in the Microchip LAN8700/LAN8700i data sheet, including the 36-QFN pin-description table and exposed-pad layout. Use that table when assigning MII or RMII signals, supplies, clocks, reset, power-down, and magnetics-side pins. The exposed pad is a thermal and electrical connection that must follow the manufacturer’s recommended PCB land pattern.
Is the LAN8700C-AEZG-AR2 automotive grade?
The LAN8700C-AEZG-AR2 is the automotive-ordering option in the LAN8700C family, with the “AR2” suffix identifying the automotive variant. The automotive qualification grade and applicable AEC-Q100 test report should be confirmed in Microchip’s ordering or qualification documentation before use in a safety-related vehicle design. Its 36-QFN package and 10/100 Ethernet PHY functions align with compact automotive networking equipment.
What is the difference between MII and RMII on the LAN8700C-AEZG-AR2?
MII provides a wider parallel interface and generally supports a higher host clock rate, while RMII uses fewer signals and is appropriate for host controllers with integrated or dedicated RMII support. The Microchip LAN8700/LAN8700i data sheet identifies both full MII and RMII interfaces on this PHY family. The choice therefore depends on the selected host controller, board routing constraints, clocking strategy, and required throughput.
Does LAN8700C-AEZG-AR2 support Auto-MDIX?
Yes, the LAN8700C-AEZG-AR2 supports HP Auto-MDIX, allowing the PHY to detect the cable orientation and handle straight-through or crossover connections automatically. According to the Microchip LAN8700/LAN8700i data sheet, this feature simplifies installation in embedded systems where direct cable-end inspection is inconvenient. It does not remove the need for a correctly designed magnetics and termination network.
What is the best drop-in replacement for LAN8700C-AEZG-AR2?
The closest same-footprint replacement is LAN8700C-AEZG, provided its temperature grade and qualification requirements satisfy the target application. Both parts use the 36-QFN (6 × 6) package and implement the same LAN8700C 10/100 Ethernet PHY with MII/RMII and HP Auto-MDIX. Check automotive qualification, temperature range, lifecycle status, and exact PCB footprint before treating it as a production substitution.
Can LAN8700IC-AEZG replace LAN8700C-AEZG-AR2?
LAN8700IC-AEZG is a close same-family candidate for review, but it should not be treated as an automatic drop-in replacement for LAN8700C-AEZG-AR2. Both are associated with the 36-pin AEZG package and the same 10/100 Ethernet PHY family, yet the “I” ordering option can represent a different industrial or temperature grade. Confirm the manufacturer ordering table, automotive qualification, exposed-pad layout, and operating-temperature limits before substitution.
LAN8700C-AEZG-AR2 vs LAN8700C-AEZG-AR2-TR?
The -TR ordering suffix normally identifies a tape-and-reel shipping configuration, while the base AEZG suffix identifies the device without that reel-code suffix. They can represent the same electrical device when the ordering table confirms the underlying silicon and temperature grade. Package-pin compatibility is expected, but procurement drawings and assembly BOMs must distinguish the shipment format. Verify the exact Microchip ordering information before approving the substitution.
When should I choose LAN8700C-AEZG-AR2 over another Ethernet PHY?
Choose LAN8700C-AEZG-AR2 when an embedded design needs a compact 10/100 Mb/s PHY with full MII or RMII, HP Auto-MDIX, variable I/O voltage, low-power flexPWR operation, and the automotive AR2 ordering profile. Select a different PHY only when the system requires features outside this device’s scope, such as multi-gigabit rates, a different host interface, integrated magnetics, or a package and qualification profile that better matches the end product.
Is LAN8700C-AEZG-AR2 suitable for industrial gateways?
Yes, the LAN8700C-AEZG-AR2 is suitable for many compact industrial Ethernet gateways because it supports 10/100 Mb/s data rates, MII and RMII host interfaces, HP Auto-MDIX, variable I/O voltage, and ±15 kV ESD-protected cable connections. The “AR2” automotive ordering option may suit harsh environments, but the designer must still confirm temperature, transient, isolation, and regulatory requirements for the final industrial installation.
Where to buy LAN8700C-AEZG-AR2 and what is its price?
Use the “Request a Quote” form on this page to ask about LAN8700C-AEZG-AR2 availability, unit pricing, quantity breaks, lead time, and approved shipping arrangements. The exact AR2 ordering code is a 36-QFN automotive variant, so its commercial terms may differ from the industrial-temperature LAN8700C-AEZG. Quote requests should include your target quantity, date code preference, production schedule, and reel or tray requirements.
What are the key specifications engineers should know about LAN8700C-AEZG-AR2?
The principal specifications are 10/100 Mb/s Ethernet operation, full MII and RMII host interfaces, HP Auto-MDIX support, a 1.6 V to 3.6 V core-supply range, variable I/O voltage, ±15 kV ESD protection, and a 36-QFN (6 mm × 6 mm) package with an exposed pad. The Microchip LAN8700/LAN8700i data sheet also identifies the low-power flexPWR architecture. These characteristics define its suitability for compact embedded and automotive Ethernet links.

工程参考数据: LAN8700C-AEZG-AR2 ——对比、设计指导和合规信息。

选型指南

Choose LAN8700C-AEZG-AR2 for compact automotive or harsh-environment Ethernet designs that require the exact AR2 ordering profile, a 36-QFN footprint, 10/100 Mb/s operation, and both MII and RMII host options. Its ±15 kV ESD protection and HP Auto-MDIX are useful in field-wired equipment, while variable I/O voltage simplifies interoperability with host logic. LAN8700C-AEZG is the closest base-ordering candidate when the original automotive suffix is unnecessary and the required environmental qualification is satisfied. LAN8700IC-AEZG may suit an industrial design, but the I and AR2 ordering codes must be checked against temperature and qualification requirements before substitution. Neither PHY is appropriate when the system requires multi-gigabit Ethernet, integrated magnetics, or a host interface other than MII/RMII.

与替代料对比

参数 本产品 LAN8700C-AEZG LAN8700IC-AEZG
Package 36-QFN (6 mm × 6 mm) 36-QFN (6 mm × 6 mm) 36-QFN (6 mm × 6 mm)
Brand Microchip Technology Microchip Technology Microchip Technology
Ethernet Data Rate 10 Mb/s or 100 Mb/s 10 Mb/s or 100 Mb/s 10 Mb/s or 100 Mb/s
Host Interface Full MII and RMII Full MII and RMII Full MII and RMII
Auto-MDIX HP Auto-MDIX supported HP Auto-MDIX supported HP Auto-MDIX supported
ESD Protection ±15 kV ±15 kV ±15 kV
Core Supply Voltage 1.6 V to 3.6 V 1.6 V to 3.6 V 1.6 V to 3.6 V
I/O Voltage Variable Variable Variable
Ordering Profile Automotive AR2 Base ordering option Industrial-oriented ordering option
Low-Power Technology flexPWR flexPWR flexPWR

关键差异点

  • Automotive-specific ordering option (对比 LAN8700C-AEZG)
  • Compact 36-QFN implementation (对比 LAN8700IC-AEZG)
  • Both parallel and reduced-pin host interfaces (对比 LAN8700IC-AEZG)

设计说明

Use the manufacturer’s 36-QFN land pattern and exposed-pad via arrangement exactly; no 36-pin QFN drawing is present in the selected package library. Place the PHY and its decoupling capacitors near the relevant supply pins, keep the exposed pad connected to the intended ground or thermal plane, and route MII or RMII signals away from the magnetics-side network interface. Correct pad geometry and escape routing are critical because a mechanically compatible outline does not guarantee electrical layout compatibility.

Decouple each required supply rail independently with the capacitance and ESR range specified in the Microchip data sheet. The PHY core operates from 1.6 V to 3.6 V, while variable I/O voltage allows the digital interface to use another compatible level. Keep supply and ground planes continuous under the device, connect the exposed pad through multiple thermal vias where permitted, and avoid sharing high-current return paths with sensitive magnetics-side traces.

Do not substitute LAN8700C-AEZG, LAN8700IC-AEZG, or a reel-code variant solely because the connector and package outline match. Confirm the exact ordering code, operating-temperature range, automotive qualification, shipment format, exposed-pad connection, and active lifecycle status. A functional PHY description does not establish that two ordering options are equivalent for production use in a vehicle or harsh industrial environment.

Treat the cable-side network interface as a high-speed differential signal region. Follow the reference schematic and layout for the isolation or network magnetics, termination, center-tap capacitance, and differential pair geometry. Keep the PHY-to-magnetics path short and symmetric, and avoid placing unrelated digital or switching-regulator routing beneath the sensitive pair. Validate the complete board with the manufacturer’s recommended Ethernet test equipment.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The exact automotive AR2 ordering code is associated with an automotive product profile, but the specific RoHS, REACH, AEC-Q100 grade, lead-free, halogen-free, and conflict-minerals declarations require confirmation from Microchip’s ordering or qualification documentation.

数据核验日期: 2026-11-14 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

lan8700c aezg tr LAN8700C-AEZG-AR2 datasheet LAN8700C-AEZG-AR2 datasheet pdf LAN8700C-AEZG-AR2 pinout LAN8700C-AEZG-AR2 equivalent LAN8700C-AEZG-AR2 replacement LAN8700C-AEZG-AR2 cross reference LAN8700C-AEZG-AR2 price LAN8700C-AEZG-AR2 stock Microchip LAN8700C-AEZG-AR2 LAN8700C-AEZG-AR2 QFN-36 footprint LAN8700C-AEZG-AR2 MII RMII LAN8700C-AEZG-AR2 automotive Ethernet LAN8700C-AEZG-AR2 vs LAN8700C-AEZG

相关元器件 & 术语

Microchip Technology LAN8700C-AEZG-AR2 LAN8700C-AEZG LAN8700IC-AEZG Ethernet PHY physical-layer transceiver network interface IC 10BASE-T 100BASE-T MII RMII HP Auto-MDIX flexPWR variable I/O voltage ±15 kV ESD protection 36-QFN QFN package family surface-mount package exposed thermal pad automotive Ethernet industrial Ethernet gateway embedded Linux Ethernet magnetics AEC-Q100 RoHS
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情