LAN8700C-AEZG-AR2 - 10/100 Ethernet PHY | Microchip | Automotive
MPN: LAN8700C-AEZG-AR2 ✓ פעילLAN8700C-AEZG-AR2 סקירה
An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts logical data supplied by a host controller into signals suitable for twisted-pair Ethernet cabling. It belongs to the transceiver and interface-IC hierarchy within network semiconductor solutions. This LAN8700 variant is intended for automotive and industrial embedded systems where low-power operation, compact packaging, cable flexibility, and robust transient protection are important design considerations.
Key characteristics include support for 10 Mb/s and 100 Mb/s operation, full MII and RMII controller interfaces, HP Auto-MDIX support, and ±15 kV ESD-protected cable-side connections. The variable I/O voltage architecture allows the digital interface voltage to be selected independently of the analog PHY supply, simplifying integration with host processors operating at different logic levels. The automotive AR2 ordering option supports design environments requiring an extended automotive qualification profile.
The LAN8700 architecture combines an analog 10/100 Ethernet front end with digital data-path logic and an integrated 1.6 V to 3.6 V low-power core. Its exposed thermal pad provides a direct heat-transfer path from the IC into the PCB. The 6 mm × 6 mm QFN-36 footprint also requires careful escape routing for its MII or RMII signals, clock inputs, power rails, and magnetics-side connections.
Typical uses include automotive infotainment controllers, industrial Ethernet gateways, embedded Linux platforms, set-top equipment, and compact communications modules. The MII interface provides a parallel data path for higher host clock rates, while RMII reduces pin count and board-routing pressure in designs where the host controller supports it. Auto-MDIX simplifies installation by allowing the PHY to handle straight-through or crossover cable connections automatically.
Designers should follow the manufacturer datasheet for the exposed-pad land pattern, decoupling, magnetic-component selection, cable termination, and separation between analog and digital circuitry. This page combines package, interface, protection, and application information with replacement guidance and engineering-focused design notes to support PCB and firmware implementation.
חלופות תחליף ישיר עבור LAN8700C-AEZG-AR2 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LAN8700C-AEZG-AR2 (אותו גורם צורה וטביעת רגל) — שונים ב Host Interface, Package.
LAN8700C-AEZG
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LAN8700IC-AEZG
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LAN8700C-AEZG-AR2 מפרטים
| Ethernet Data Rate | 10 Mb/s or 100 Mb/s |
| Host Interface | Full MII and RMII |
| Auto-MDIX | HP Auto-MDIX supported |
| ESD Protection | ±15 kV |
| Core Supply Voltage Range | 1.6 V to 3.6 V |
| Variable I/O Voltage | Supported |
| מארז | 36-QFN (6 mm × 6 mm) |
| Exposed Thermal Pad | Present |
| סוג הרכבה | Surface mount |
| Qualification Profile | Automotive |
| Product Family | LAN8700 |
| PHY Type | Single-channel 10/100 Ethernet transceiver |
| Technology | flexPWR |
| Cable Support | 10/100BASE-T twisted-pair Ethernet |
| Duplex Operation | Full-duplex |
מדריך תצורת פינים של LAN8700C-AEZG-AR2 36-qfn (6 mm × 6 mm)
תצורת פינים עבור LAN8700C-AEZG-AR2 (מארזת 36-qfn (6 mm × 6 mm)). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור LAN8700C-AEZG-AR2.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
LAN8700C-AEZG-AR2 מתאים עבור 6 יישוםs: Automotive Infotainment Ethernet, Industrial Ethernet Gateway, Embedded Linux Communication Module, Automotive Telematics Unit, Set-Top Box and Media Terminal, Robotics and Sensor Network Node.
Automotive Infotainment Ethernet
The LAN8700C-AEZG-AR2 fits compact automotive infotainment and connectivity modules that require a 10/100 Mb/s Ethernet link to a host processor. Its full MII interface supports a parallel host data path, while RMII can reduce connection count when the controller supports that mode. The 36-QFN (6 mm × 6 mm) package preserves board area, and ±15 kV cable-side ESD protection adds a useful layer of ruggedness. Auto-MDIX also simplifies installation by supporting straight-through and crossover cables. The exposed pad should be connected to the PCB thermal plane using the manufacturer’s recommended via pattern.
מומלץ
Industrial Ethernet Gateway
The LAN8700C-AEZG-AR2 can provide the physical layer for an industrial gateway connecting an embedded controller to a 10/100BASE-T network. Its low-power 1.6 V to 3.6 V core operation and variable I/O voltage simplify integration with processors using a different logic voltage. HP Auto-MDIX reduces installation complexity in field equipment, while the MII option supports host clocks commonly used by industrial controllers. The 36-QFN exposed-pad package requires careful thermal-pad layout and controlled copper connectivity for reliable heat transfer.
מומלץ
Embedded Linux Communication Module
The LAN8700C-AEZG-AR2 is appropriate for compact embedded Linux communication modules that require reliable 10/100 Mb/s Ethernet connectivity. RMII reduces the number of host connections and board-routing requirements, while full MII remains available when the host interface timing requires it. Auto-MDIX improves deployment flexibility, and the ±15 kV ESD rating supports protection around the external cable interface. The designer should isolate the analog and digital supplies, keep the exposed pad thermally connected, and follow the reference layout for magnetics-side components.
מומלץ
Automotive Telematics Unit
The LAN8700C-AEZG-AR2 suits automotive telematics and vehicle-network gateway equipment requiring a compact 10/100 Ethernet physical layer. The AR2 automotive ordering profile is a key reason to prefer this exact suffix over a generic industrial grade, while HP Auto-MDIX simplifies connection to service equipment and external network hardware. Full MII offers a wide parallel interface for compatible controllers, whereas RMII can simplify wiring in space-constrained nodes. Transient protection is especially relevant where cables leave the protected enclosure.
מומלץ
Set-Top Box and Media Terminal
The LAN8700C-AEZG-AR2 provides a compact Ethernet front end for set-top boxes, media terminals, and residential equipment requiring 10/100 Mb/s connectivity. Its variable I/O voltage supports integration with host logic that does not use the PHY core voltage directly, while Auto-MDIX removes manual polarity checks during installation. The QFN-36 footprint reduces board area compared with larger transceivers, but its dense escape routing requires careful component placement. Adequate decoupling and a continuous exposed-pad thermal connection are essential for reliable operation.
מומלץ
Robotics and Sensor Network Node
The LAN8700C-AEZG-AR2 can serve as the Ethernet physical layer in a compact robot controller or distributed sensor node that needs 10/100 Mb/s connectivity. RMII is useful when the host controller already includes that interface, reducing wiring and routing overhead in a crowded control board. HP Auto-MDIX helps technicians connect nodes without manually configuring crossover cables, and ESD-protected cable connections support field-installed equipment. The exposed pad should be tied to a low-impedance thermal plane, and magnetics-side traces should be kept away from sensitive signal paths.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LAN8700C-AEZG-AR2 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LAN8700C-AEZG | LAN8700IC-AEZG |
|---|---|---|---|
| Package | 36-QFN (6 mm × 6 mm) | 36-QFN (6 mm × 6 mm) | 36-QFN (6 mm × 6 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Ethernet Data Rate | 10 Mb/s or 100 Mb/s | 10 Mb/s or 100 Mb/s | 10 Mb/s or 100 Mb/s |
| Host Interface | Full MII and RMII | Full MII and RMII | Full MII and RMII |
| Auto-MDIX | HP Auto-MDIX supported | HP Auto-MDIX supported | HP Auto-MDIX supported |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV |
| Core Supply Voltage | 1.6 V to 3.6 V | 1.6 V to 3.6 V | 1.6 V to 3.6 V |
| I/O Voltage | Variable | Variable | Variable |
| Ordering Profile | Automotive AR2 | Base ordering option | Industrial-oriented ordering option |
| Low-Power Technology | flexPWR | flexPWR | flexPWR |
מבדילים עיקריים
- Automotive-specific ordering option (לעומתLAN8700C-AEZG)
- Compact 36-QFN implementation (לעומתLAN8700IC-AEZG)
- Both parallel and reduced-pin host interfaces (לעומתLAN8700IC-AEZG)
הערות תכנון
Use the manufacturer’s 36-QFN land pattern and exposed-pad via arrangement exactly; no 36-pin QFN drawing is present in the selected package library. Place the PHY and its decoupling capacitors near the relevant supply pins, keep the exposed pad connected to the intended ground or thermal plane, and route MII or RMII signals away from the magnetics-side network interface. Correct pad geometry and escape routing are critical because a mechanically compatible outline does not guarantee electrical layout compatibility.
Decouple each required supply rail independently with the capacitance and ESR range specified in the Microchip data sheet. The PHY core operates from 1.6 V to 3.6 V, while variable I/O voltage allows the digital interface to use another compatible level. Keep supply and ground planes continuous under the device, connect the exposed pad through multiple thermal vias where permitted, and avoid sharing high-current return paths with sensitive magnetics-side traces.
Do not substitute LAN8700C-AEZG, LAN8700IC-AEZG, or a reel-code variant solely because the connector and package outline match. Confirm the exact ordering code, operating-temperature range, automotive qualification, shipment format, exposed-pad connection, and active lifecycle status. A functional PHY description does not establish that two ordering options are equivalent for production use in a vehicle or harsh industrial environment.
Treat the cable-side network interface as a high-speed differential signal region. Follow the reference schematic and layout for the isolation or network magnetics, termination, center-tap capacitance, and differential pair geometry. Keep the PHY-to-magnetics path short and symmetric, and avoid placing unrelated digital or switching-regulator routing beneath the sensitive pair. Validate the complete board with the manufacturer’s recommended Ethernet test equipment.
מידע על תאימות
The exact automotive AR2 ordering code is associated with an automotive product profile, but the specific RoHS, REACH, AEC-Q100 grade, lead-free, halogen-free, and conflict-minerals declarations require confirmation from Microchip’s ordering or qualification documentation.