Microchip Technology

LAN91C93I-MC Full-Duplex Ethernet Controller | Microchip

料号: LAN91C93I-MC ✓ 量产中
100-pin QFP Package
最小起订量: 1 |

LAN91C93I-MC 概述

Microchip Technology LAN91C93I-MC is a non-PCI single-chip full-duplex Ethernet controller with a 1.25 MB/s data rate, 10 Base-T PHY interface, CMOS process technology, and a 100-pin QFP package. It combines local-bus Ethernet controller functionality with independent transmit and receive operations for switched-Ethernet systems.

An Ethernet controller is a semiconductor interface between a host processor and an Ethernet network. Within the product hierarchy, LAN91C93I-MC is an Ethernet controller, network interface controller, interface IC, and semiconductor. Its local-bus architecture avoids requiring a PCI bus while giving embedded processors direct access to Ethernet communication functions through a comparatively simple software interface.

The controller supports full-duplex switched Ethernet and maintains independent transmit and receive operations. This architecture can improve effective communication concurrency compared with a controller that must coordinate both directions through one path. The 1.25 MB/s rated transfer rate and 10 Base-T PHY interface identify the LAN91C93I-MC as a 10 Mb/s-class embedded Ethernet solution rather than a Fast Ethernet or Gigabit Ethernet controller.

According to the manufacturer datasheet, LAN91C93I is designed to be 100% software compatible with LAN91C92, LAN91C94, and LAN91C96 when operating in local-bus mode. This compatibility is particularly useful when preserving an established driver and application interface is more important than redesigning the entire network software stack. The integrated device also retains LAN91C92 functionality for local-bus environments.

Typical applications include embedded industrial control, instrument networking, embedded appliance connectivity, point-of-sale equipment, and legacy embedded systems that require full-duplex switched Ethernet. The 100-QFP package exposes the controller's processor-side, memory-side, Ethernet, and power connections through a relatively high pin count suited to multilayer or through-hole-compatible board assembly.

Designers should verify the complete pin description, voltage limits, clocking requirements, initialization sequence, and transceiver interface in the manufacturer datasheet before layout release. They should also confirm that the external magnetics, RJ-5 interface, isolation requirements, and system grounding topology suit the target network environment rather than assuming that the controller alone constitutes a complete Ethernet interface.

This product overview combines the manufacturer interface description, package details, software-compatibility information, verified alternatives, and practical selection considerations. It also identifies where an engineer must consult the official datasheet for complete electrical limits and PCB implementation details.

直接替换替代料: LAN91C93I-MC ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: LAN91C93I-MC (相同外形与封装尺寸) ——差异在于 Data Rate, Product Type.

Microchip Technology
Data Rate: 10 Mbps
Product Type: Single-chip Ethernet controller
对比 LAN91C93I-MC →

LAN91C93I-MS

✅ 直接替换
Microchip Technology
📦 QFP-100 (14 x 20 mm)
Single-chip Ethernet controller · IEEE 802.3 · 10 Mbps · 10BASE-T PHY interface · Local bus, non-PCI · Full-duplex switched Ethernet · Fully independent transmit and receive operations · 3.3 V or 5 V

联系询价

查看数据手册 →

LAN91C93I-MC 规格参数

Product Type Non-PCI single-chip Ethernet controller
Ethernet Mode Full-duplex switched Ethernet
数据速率 1.25 MB/s
PHY Interface IEEE 802.3 10 Base-T
Channel Count 2 channels
Bus Architecture Local bus
PCI Interface No PCI interface
Transmit and Receive Operation Fully independent transmit and receive operations
Software Compatibility 100% compatible with LAN91C92, LAN91C94, and LAN91C96 in local-bus mode
Process Technology CMOS
封装 100-pin QFP
Package Body Size 14 x 20 mm
Terminal Form Gull wing
Temperature Grade Industrial
安装类型 Surface mount

LAN91C93I-MC 14 x 20 mm 引脚配置指南

LAN91C93I-MC(14 x 20 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

LAN91C93I-MC 的 14 x 20 mm 封装引脚图

暂无详细引脚数据: LAN91C93I-MC.

请参阅 数据手册 以查看完整引脚配置。

典型应用

LAN91C93I-MC 适用于 6 应用s: Industrial Embedded Controller Networking, Embedded Instrument Data Acquisition, Embedded Appliance Connectivity, Point-of-Sale Terminal, Legacy Network Interface Upgrade, Networked Process Monitoring.

🏭

Industrial Embedded Controller Networking

The LAN91C93I-MC fits industrial embedded controllers that exchange supervisory and configuration data over a 10 Mb/s Ethernet network. Its 1.25 MB/s data rate is suitable for moderate-rate local traffic, while full-duplex switched Ethernet and independent transmit and receive paths support simultaneous control traffic and status reporting. The local-bus interface avoids a PCI dependency and can simplify integration with a processor that already uses a dedicated network interface. Before schematic release, verify the processor-bus timing, reset sequence, PHY connectivity, and operating limits in the manufacturer datasheet.

🖥️

Embedded Instrument Data Acquisition

LAN91C93I-MC is appropriate for data-acquisition instruments that must transfer measurements, configuration packets, and diagnostic records through Ethernet. Its 1.25 MB/s rate is relevant to moderate-volume operational data rather than continuous high-bandwidth streaming. Full-duplex operation allows measurement traffic and management commands to coexist, while the 10 Base-T interface provides a conventional network attachment point. Validate PHY magnetics, isolation, grounding, and the required transceiver implementation as part of the complete Ethernet front end.

🧩

Embedded Appliance Connectivity

The LAN91C93I-MC can connect an embedded appliance to a 10 Mb/s Ethernet network for configuration, status monitoring, and service access. The non-PCI local-bus architecture is useful when the host processor has no conventional PCI bus or when the appliance requires a dedicated network controller. Its fully independent transmit and receive operations support bidirectional communication on switched networks. Designers should confirm that the 100-QFP footprint, software driver requirements, and external network interface suit the appliance's mechanical and thermal design.

🏭

Point-of-Sale Terminal

A point-of-sale terminal can use LAN91C93I-MC for transaction traffic, peripheral status exchange, and network management over full-duplex Ethernet. The 1.25 MB/s rate is suitable for intermittent commercial transactions and control data, while independent transmit and receive paths help avoid unnecessary contention between uploads and responses. The local-bus interface allows the controller to operate without a PCI peripheral bus. Before deployment, assess the product's long-term software support, security needs, and whether the physical network and connector implementation meet site requirements.

🔧

Legacy Network Interface Upgrade

LAN91C93I-MC is useful when upgrading an established local-bus embedded network design that requires full-duplex switched Ethernet without changing the software model. The manufacturer reports 100% software compatibility with LAN91C92, LAN91C94, and LAN91C96 in local-bus mode, reducing driver-porting effort. Hardware migration still requires exact pin, timing, voltage, and mechanical checks because software compatibility alone does not prove drop-in interchangeability. This makes LAN91C93I-MC most attractive in controlled redesigns where board changes can be planned and tested.

🌐

Networked Process Monitoring

LAN91C93I-MC supports process-monitoring nodes that periodically report sensor state, alarms, and operating counters to a supervisory network. Its 1.25 MB/s rate accommodates typical low-bandwidth telemetry, and full-duplex operation permits status reports and configuration commands to proceed independently. The industrial-temperature designation makes it a candidate for embedded monitoring equipment, subject to confirmation of the complete operating-temperature range and environmental qualification. The board should also provide a suitable Ethernet isolation or surge-protection strategy.

推荐产品汇总

LAN91C92 Local-bus software-compatible controller family 用于: Industrial Embedded Controller Networking, Embedded Appliance Connectivity, Legacy Network Interface Upgrade, Networked Process Monitoring LAN91C93I-MS Microchip Technology 用于: Industrial Embedded Controller Networking, Embedded Appliance Connectivity, Point-of-Sale Terminal, Networked Process Monitoring LAN91C94 Local-bus software-compatible controller family 用于: Embedded Instrument Data Acquisition, Point-of-Sale Terminal, Legacy Network Interface Upgrade LAN91C96 Local-bus software-compatible controller family 用于: Embedded Instrument Data Acquisition, Legacy Network Interface Upgrade
What is the LAN91C93I-MC?
The LAN91C93I-MC is a non-PCI single-chip Ethernet controller from Microchip Technology that provides a 1.25 MB/s data rate and a 10 Base-T PHY interface in a 100-pin QFP package. According to the manufacturer datasheet, the controller supports full-duplex switched Ethernet with fully independent transmit and receive operations for local-bus embedded systems.
What are the key specifications of LAN91C93I-MC that engineers should know?
The key LAN91C93I-MC specifications are a 1.25 MB/s data rate, IEEE 802.3 10 Base-T PHY interface, full-duplex operation, independent transmit and receive paths, local-bus architecture, and a 100-pin QFP package. The manufacturer also identifies it as a CMOS device intended for industrial-temperature operation and software compatible with LAN91C92, LAN91C94, and LAN91C96 in local-bus mode.
Where can I download the LAN91C93I-MC datasheet PDF?
The LAN91C93I-MC datasheet PDF is available from the verified manufacturer-document link on this page. The document is titled “Non-PCI Single-Chip Full Duplex Ethernet Controller” and describes local-bus operation, full-duplex switched Ethernet, independent transmit and receive functions, and compatibility with the LAN91C92, LAN91C94, and LAN91C96 software interface.
Where can I find the LAN91C93I-MC pinout?
The LAN91C93I-MC pin assignment is found in the pin-description section of the manufacturer datasheet rather than in the package diagram available on this page. Because the complete numbered pin list was not established from the product-page excerpts, no individual signal names are assigned here. Use the official datasheet to verify every power, ground, local-bus, Ethernet, clock, and control connection before routing the PCB.
Is the LAN91C93I-MC a PCI Ethernet controller?
The LAN91C93I-MC is not a PCI Ethernet controller; it is explicitly described as a non-PCI device. It uses a local-bus interface and is intended for embedded processor systems that do not use a PCI host bus. This distinction matters when selecting the controller because software drivers, bus interfacing, and board-level schematic assumptions differ substantially from a PCI-based network adapter.
Can LAN91C93I-MC support full-duplex switched Ethernet?
Yes, the LAN91C93I-MC supports full-duplex switched Ethernet and provides fully independent transmit and receive operations. According to the manufacturer datasheet, those independent paths allow the two directions of communication to proceed separately. The design is intended for local-bus embedded applications where simultaneous network traffic is required without a PCI interface.
What is the difference between LAN91C93I-MC and LAN91C92?
The principal documented difference is that LAN91C93I adds full-duplex switched-Ethernet support and fully independent transmit and receive operations while retaining LAN91C92 functionality for local-bus environments. The manufacturer states that LAN91C93I is 100% software compatible with LAN91C92, LAN91C94, and LAN91C96 in local-bus mode. Pin-level interchangeability between those related devices is not established by the product excerpts.
Is LAN91C93I-MC software compatible with LAN91C94 and LAN91C96?
Yes, the manufacturer datasheet states that LAN91C93I is 100% software compatible with LAN91C94 and LAN91C96 when operating in local-bus mode. This supports driver and application portability within the indicated operating mode. It should not be interpreted as proof that every device is a drop-in replacement, because package pin assignments and electrical operating conditions still require separate verification.
When should I choose LAN91C93I-MC instead of LAN91C92?
Choose LAN91C93I-MC when the design requires full-duplex switched Ethernet with independent transmit and receive operations while retaining a local-bus software model. LAN91C92 remains relevant when the existing architecture only requires its established local-bus functionality. Because the manufacturer reports 100% software compatibility in local-bus mode, migration can be evaluated without immediately changing the entire network software interface.
Is LAN91C93I-MC suitable for an industrial embedded controller?
The LAN91C93I-MC is identified as an industrial-temperature Ethernet controller with a 100-pin QFP package, making it suitable for evaluation in industrial embedded-control systems. Its 1.25 MB/s 10 Base-T interface is appropriate for supervisory data, configuration traffic, and moderate-rate device networking. Final suitability still depends on the verified electrical limits, environmental qualification, and operating-temperature limits in the manufacturer datasheet.
What can replace the LAN91C93I-MC?
The only same-package option shown by the verified product listings is LAN91C93I-MS, which is identified as a Microchip Technology Ethernet controller in a 100-QFP package. However, the available excerpts do not establish its complete temperature grade, electrical limits, or pin-for-pin equivalence. Treat it as a candidate for engineering review rather than an unconditional replacement, and verify the manufacturer documentation before approving a substitution.
Is LAN91C93I-MS the same as LAN91C93I-MC?
LAN91C93I-MS and LAN91C93I-MC are closely related Microchip Technology ordering codes, and the available listing identifies LAN91C93I-MS as a 100-QFP Ethernet controller with an IEEE 802.3 10 Base-T PHY interface. They are not proven identical from the available documentation because the suffix-specific temperature, packing, and qualification details are not stated. Review the ordering table and datasheet before treating it as a drop-in substitution.
What is the best cross-brand equivalent for the LAN91C93I-MC?
No verified cross-brand, pin-compatible equivalent for the LAN91C93I-MC was identified. The manufacturer and third-party cross-reference results provide comparison tools but do not name a competitor device with a confirmed 100-QFP footprint, equivalent local-bus interface, and matching electrical characteristics. A valid cross-brand selection would require documented pin compatibility, timing, voltage, software, and thermal equivalence rather than a generic 10 Mb/s controller match.
Where can I buy LAN91C93I-MC online?
Use the “Request a Quote” form on this page to request LAN91C93I-MC sourcing, current availability, and a lead-time quotation. The structured listing has no qualifying quantity-break price, so it does not display a static unit-price table. For design traceability, identify the exact ordering code LAN91C93I-MC and the required package and quantity when submitting the request.
What is the price and lead time of LAN91C93I-MC?
The current price and lead time for LAN91C93I-MC should be requested through the “Request a Quote” form on this page because no qualifying exact-MPN quantity-break table is available. The request should state the required quantity, date code policy, target price, and whether an industrial-temperature 100-QFP assembly is required. This preserves current commercial accuracy for a legacy embedded Ethernet controller.

工程参考数据: LAN91C93I-MC ——对比、设计指导和合规信息。

选型指南

Choose LAN91C93I-MC for an embedded design that requires a non-PCI, local-bus 10 Base-T controller with a 1.25 MB/s data rate and full-duplex switched-Ethernet operation. It is especially attractive when the host software already targets the local-bus-compatible LAN91C92, LAN91C94, or LAN91C96 interface, because the manufacturer reports 100% software compatibility in that mode. LAN91C93I-MS is the closest ordering-code candidate found, but verify its suffix-specific temperature grade, electrical limits, and pin assignment before treating it as a drop-in replacement. The related LAN91C92, LAN91C94, and LAN91C96 devices are valuable architectural references but should not be selected solely from software compatibility. A cross-brand controller should be considered only after confirming the same 100-QFP footprint, equivalent local-bus timing, matching supply requirements, driver model, and Ethernet front-end behavior.

与替代料对比

参数 本产品 LAN91C93I-MS
Brand Microchip Technology Microchip Technology
Package QFP-100 (14 x 20 mm) 100-QFP (14 x 20 mm) - same package family
Product Type Non-PCI single-chip Ethernet controller Ethernet controller
Ethernet Interface IEEE 802.3 10 Base-T PHY interface IEEE 802.3 10 Base-T PHY interface

关键差异点

  • Adds full-duplex switched-Ethernet operation while retaining the local-bus software model (对比 LAN91C92)
  • Avoids a PCI bus dependency in embedded Ethernet designs (对比 LAN91C93I-MS)
  • Provides a 100-pin industrial-temperature QFP implementation (对比 LAN91C93I-MS)

设计说明

Route the local-bus signals according to the manufacturer datasheet, paying particular attention to clock, address, data, and control timing. A 100-QFP package provides many closely spaced terminals, so use an appropriate via fanout and avoid long stubs beneath the device. The PCB layout should also provide a stable ground plane and short return paths because the Ethernet PHY and digital control sections operate in the same high-density footprint.

Follow the reference network interface in the manufacturer datasheet when connecting the controller to Ethernet magnetics and the RJ-45 network. Preserve the specified differential-impedance geometry, separation from noisy switching paths, and grounding arrangement at the isolation boundary. The controller's 10 Base-T PHY capability does not define the complete external Ethernet front end, which also requires suitable magnetics and protection components.

Do not interpret the documented software compatibility among LAN91C93I, LAN91C92, LAN91C94, and LAN91C96 as proof of identical pinout or electrical interchangeability. Confirm ordering suffixes, temperature grade, package dimensions, clock requirements, supply voltage, reset behavior, and signal directions against the relevant manufacturer documentation. A replacement should be approved only after schematic, timing, and firmware regression checks pass.

Place decoupling structures directly at the appropriate power terminals and follow the manufacturer's recommended layout for clocks and sensitive interfaces. Keep the Ethernet-side magnetics and protection components near the board connector rather than routing high-speed digital signals through the network front end. Provide thermal copper around the 100-pin QFP where practical, while checking the exposed thermal requirements and package-specific land pattern in the official documentation.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The product is an industrial-temperature Ethernet controller rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the manufacturer product-page excerpts.

相关搜索

LAN91C93I-MC datasheet LAN91C93I-MC datasheet pdf LAN91C93I-MC pinout LAN91C93I-MC specifications LAN91C93I-MC equivalent LAN91C93I-MC replacement LAN91C93I-MC cross reference LAN91C93I-MC 100 QFP LAN91C93I-MC application circuit LAN91C93I-MC price LAN91C93I-MC stock Microchip LAN91C93I-MC LAN91C93I-MC vs LAN91C93I-MS LAN91C93I-MC local bus Ethernet controller LAN91C93 full duplex Ethernet controller

相关元器件 & 术语

Microchip Technology LAN91C93I-MC LAN91C93I LAN91C93I-MS LAN91C92 LAN91C94 LAN91C96 Ethernet controller network interface controller interface IC semiconductor non-PCI controller local-bus architecture IEEE 802.3 10 Base-T full-duplex switched Ethernet 1.25 MB/s independent transmit and receive CMOS QFP-100 gull-wing package surface-mount package industrial temperature grade Ethernet magnetics RJ-45 interface
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情