LC4064B-75T44I - 64-Macrocell 7.5ns CPLD | Lattice Semiconductor
料号: LC4064B-75T44I ✗ 停产LC4064B-75T44I 概述
A complex programmable logic device, or CPLD, is a programmable digital semiconductor that sits between fixed-function logic and an FPGA in the design hierarchy. A CPLD combines a programmable AND-array with a programmable OR-array, providing deterministic routing, nonvolatile configuration storage, and fast logic implementation without an external configuration device. The ispMACH 4000B architecture places 64 macrocells in four logic array blocks for designs requiring moderate logic density and high pin-to-pin performance.
Key characteristics include 64 macrocells, four logic array blocks, a 7.5 ns speed grade, and 2.5 V operation. The 44-TQFP surface-mount package provides 44 external connections for power, configuration, clock, and user I/O. In-system programming allows the device to be configured through its programming interface without removing it from the circuit, supporting production programming, field updates, and prototype reconfiguration.
The LC4064B-75T44I is suited to designs where predictable propagation delay and compact implementation are more important than very high logic density. Its macrocell-based architecture supports combinational and registered logic, state machines, bus arbitration, address decoding, interface control, and low-latency glue logic. Device configuration is retained in nonvolatile memory, so the implemented logic remains available after power is removed and re-applied.
Typical uses include industrial control modules, peripheral controllers, data-acquisition front ends, communication equipment, and embedded system support logic. The 7.5 ns grade is appropriate for synchronous control paths and moderately clocked interfaces, while the 64-macrocell capacity provides room for decoding, handshake logic, and state-machine implementations. Its industrial-temperature ordering option also suits equipment designed for extended environmental duty.
Designers should confirm the exact supply-voltage range, pin-level I/O limits, configuration timing, and unused-pin requirements in the Lattice Semiconductor datasheet and package drawing. PCB layout should provide a short, continuous ground plane, decouple each supply rail locally, and route configuration and clock signals away from noisy switching nodes. Use the ispMACH implementation flow and timing constraints to validate every registered path before programming hardware.
This page combines the verified device identity, package information, architecture details, replacement candidates, comparison parameters, and practical design guidance in one engineering-focused reference. It also highlights where engineers must consult the original manufacturer documentation for exact pin assignments, timing tables, and power specifications.
直接替换替代料: LC4064B-75T44I ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LC4064B-75T44I (相同外形与封装尺寸) ——差异在于 Architecture, Product Family, Package, Configuration Memory, Core Supply Voltage.
LC4064C-75T44I
✅ 直接替换联系询价
查看数据手册 →LC4064V-75T44I
✅ 直接替换联系询价
查看数据手册 →LC4064B-75TN44I
✅ 直接替换📋 参考替代料(不在目录中)
LC4064B-75T44C
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LC4064B-75TN44C
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LC4064B-75T44I 最大额定值与电气特性
| Device Type | Complex Programmable Logic Device (CPLD) |
| Product Family | ispMACH 4000B |
| Macrocells | 64 macrocells |
| Logic Array Blocks | 4 logic array blocks |
| Maximum Propagation Delay | 7.5 ns |
| Maximum Operating Frequency | 168 MHz |
| Core Supply Voltage | 2.5 V |
| Family Supply Voltage Options | 1.8 V, 2.5 V, or 3.3 V |
| Programming | In-system programmable |
| Configuration Memory | Nonvolatile |
| 封装 | 44-pin TQFP, 10 x 10 mm |
| 安装类型 | Surface mount |
| 引脚数量 | 44 pins |
| Operating Temperature Grade | Industrial grade |
LC4064B-75T44I 44-pin tqfp, 10 x 10 mm 引脚配置指南
LC4064B-75T44I(44-pin tqfp, 10 x 10 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: LC4064B-75T44I.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LC4064B-75T44I 适用于 6 应用s: Industrial Control and Automation, Data-Acquisition Front End, Peripheral Interface and Bus Bridging, Communication Equipment Control Plane, Programmable Relay and Power Sequencing, Compact Embedded System Support Logic.
Industrial Control and Automation
The LC4064B-75T44I fits industrial control modules that require deterministic decoding, sequencing, and state-machine logic around a microcontroller or processor. Its 64 macrocells provide capacity for address decoding, interlock evaluation, relay-command sequencing, and watchdog handling, while the 7.5 ns maximum propagation delay supports moderately timed control paths. Nonvolatile configuration means the control logic survives power cycling without an external boot flash. The industrial-grade ordering option should be checked against the enclosure temperature range, and decoupling plus grounded return paths are essential when the module also includes switching relays or power converters.
推荐
Data-Acquisition Front End
The LC4064B-75T44I can implement channel multiplexing, sample-and-hold timing, trigger alignment, and data-format conversion in front of an ADC. The 168 MHz maximum family operating frequency and 7.5 ns propagation delay allow clocked pipelines and interface control without introducing the complexity of a large FPGA. Sixty-four macrocells are sufficient for control sequencing and register banks but not for extensive datapath storage, so high-speed data storage should remain with a dedicated ADC, FIFO, or FPGA. Keep the CPLD clock and configuration routing away from analog inputs to preserve signal integrity and predictable timing.
推荐
Peripheral Interface and Bus Bridging
The LC4064B-75T44I is useful for adapting slow legacy peripherals to a faster processor bus through address decode, read/write strobe generation, and interrupt-request control. Its 7.5 ns speed grade can support clocked handshake logic, while nonvolatile configuration simplifies standalone peripheral behavior after reset. The 44-pin package limits user I/O availability, so designers should count power, configuration, clock, and dedicated pins before committing to the device. Validate setup and hold times for the selected interface and use the Lattice timing constraints to ensure every registered path closes at the target clock.
推荐
Communication Equipment Control Plane
The LC4064B-75T44I can implement framing control, command parsing, CRC generation, and status sequencing in communication equipment while a dedicated processor handles higher-layer work. Its 64 macrocells provide enough room for compact state machines, buffer control, and programmable interrupt logic, and the 168 MHz family maximum supports clocked control paths. This device does not replace a high-speed transceiver or a large protocol processor, so analog and high-speed data paths should remain separate. Use controlled-impedance routing for clock signals and place configuration interfaces away from switching regulators to reduce susceptibility to noise-induced programming problems.
推荐
Programmable Relay and Power Sequencing
The LC4064B-75T44I can coordinate relay outputs, fault flags, timing sequences, and power-enable signals in programmable control hardware. Its 64 macrocells are well matched to sequential state machines and latched output banks, and the nonvolatile configuration allows the same sequence to run immediately after power restoration. A 7.5 ns propagation delay is more than adequate for electromechanical sequencing where millisecond-scale timing dominates. Confirm output drive ratings and isolation requirements in the datasheet, and provide flyback protection and separate return paths for inductive loads rather than routing them through CPLD pins.
推荐
Compact Embedded System Support Logic
The LC4064B-75T44I can add glue logic, boot-status decoding, watchdog handling, and power-state management around a low-cost microcontroller or FPGA. Its in-system programming allows the same PCB to be programmed during production and updated in the field, while nonvolatile storage avoids an external configuration device. The 7.5 ns propagation delay is appropriate for synchronization, pulse stretching, and register-interface adaptation rather than demanding processor-class datapath work. Designers should check the exact user-I/O count and dedicated configuration pins, since the 44-pin package reserves a meaningful portion of its leads for power and programming.
推荐
推荐产品汇总
工程参考数据: LC4064B-75T44I ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LC4064C-75T44I | LC4064V-75T44I | LC4064B-75TN44I | LC4064B-75T44C | LC4064B-75TN44C |
|---|---|---|---|---|---|---|
| Brand | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor |
| Package | 44-TQFP | 44-TQFP - same footprint | 44-TQFP - same footprint | 44-TQFP - same footprint | 44-TQFP - same footprint | 44-TQFP - same footprint |
| Device Family | ispMACH 4000B | ispMACH 4000C | ispMACH 4000V | ispMACH 4000B | ispMACH 4000B | ispMACH 4000B |
| Macrocells | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells |
| Logic Array Blocks | 4 logic array blocks | 4 logic array blocks | 4 logic array blocks | 4 logic array blocks | 4 logic array blocks | 4 logic array blocks |
| Maximum Propagation Delay | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns |
| Maximum Operating Frequency | 168 MHz | 168 MHz | 168 MHz | 168 MHz | 168 MHz | 168 MHz |
| Core Supply Voltage | 2.5 V | 2.5 V | 2.5 V | 2.5 V | 2.5 V | 2.5 V |
| Programming | In-system programmable | In-system programmable | In-system programmable | In-system programmable | In-system programmable | In-system programmable |
| Temperature Ordering Option | Industrial grade | Industrial grade | Industrial grade | Industrial grade | Commercial grade | Commercial grade |
关键差异点
- Matches the 44-TQFP land pattern while preserving the 75 speed designation (对比 LC4064V-75T44I)
- Provides an exact same-density, same-speed family migration (对比 LC4064B-75TN44I)
- Combines 64 macrocells with a seven-nanosecond-class timing grade (对比 LC4064B-75T44C)
- Offers in-system programming and nonvolatile configuration in a 44-pin package (对比 XC2C64A-5VQ100C)
设计说明
Follow the Lattice Semiconductor ispMACH 4000B power-connection and decoupling instructions for the selected 2.5 V configuration. Place the required bulk and high-frequency capacitors at the device's supply pins with short return paths to the ground plane, and confirm that power-source impedance remains low enough for simultaneous switching activity. Estimate rail droop using the worst-case I/O toggle rate and specified output-current limits, then verify the transient response on a power bus with realistic board parasitics.
Assign every net from the exact 44-TQFP pin table in the manufacturer datasheet and use the package drawing for land patterns and exposed thermal requirements. Keep configuration signals, clock inputs, and user outputs away from high-current switching nodes and inductors. Route clock and configuration nets over a continuous ground reference where possible, and avoid routing them parallel to long power-conversion or motor-drive traces. PCB signal-integrity validation is especially important when configuration is performed after board assembly.
Do not assume that an identical 44-TQFP footprint guarantees interchangeable LC4064 devices. Before substituting another family member, verify the 2.5 V operating mode, user-I/O allocation, configuration pin requirements, macrocell resource mapping, timing constraints, and bitstream support in the Lattice Semiconductor design tool. Also distinguish the 44-pin device from LC4064 options in 48-pin, 100-pin, or 208-pin packages, which have different footprints and cannot be substituted without a PCB redesign.
Treat the device clock as a timing-critical net: use a short route, provide a continuous reference plane, avoid stubs, and place any series damping close to the source when edge rates are high. Add external filtering only after confirming that it does not violate configuration or clock-input timing. For interfaces crossing between the 2.5 V core domain and a different-voltage peripheral, use level translation with direction control; the LC4064B-75T44I's I/O structure and voltage tolerances must be confirmed in the datasheet.
合规信息
The verified component information does not state RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive qualification status. The industrial suffix does not establish AEC-Q100 qualification.