LM224DTBR2 - Quad 3-32V Op Amp | onsemi | Industrial
料号: LM224DTBR2 ✓ 量产中LM224DTBR2 概述
An operational amplifier, commonly abbreviated op amp, is a voltage-controlled differential amplifier. Its inverting and non-inverting inputs allow a circuit to amplify or attenuate a signal while establishing feedback-defined gain. Within the broader semiconductor hierarchy, the LM224DTBR2 belongs to the linear amplifier family, which sits within analog integrated circuits used for instrumentation, buffering, amplification, and signal conversion. The four channels also allow several analog functions to be implemented in one compact package.
Key characteristics include a 3 V to 32 V operating supply, four amplifier circuits, true differential input capability, and a 14-pin TSSOP surface-mount package. The wide supply range allows the same device to operate from low-voltage analog systems through higher industrial rails. Its four-channel architecture reduces the number of packages required when an application needs multiple independent gain stages, although the common device supply and ground must still support every channel's operating requirements.
The LM224 series is intended for general-purpose applications rather than precision instrumentation or high-speed signal processing. Its internal architecture supports common amplifier configurations, including non-inverting, inverting, voltage follower, summing, and difference stages. Designers should account for input common-mode limits, output swing, bias current, noise, and stability requirements when selecting external resistor and capacitor values. Operating from a single supply is particularly convenient in systems that do not provide a negative analog rail.
Typical uses include conditioning sensors, buffering inputs to analog-to-digital converters, amplifying low-level control signals, implementing simple filters, and providing multiple analog channels in industrial or embedded equipment. It can also participate in audio preamplifier and mixer circuits when the required bandwidth, output swing, and distortion meet the application. Four amplifiers in one package are particularly helpful where board area is limited and several independent analog functions are required.
PCB design should provide a short return path to the ground pin and place decoupling capacitance close to the supply connection. Because all four channels share package-level supply pins, high-current output stages and sensitive input stages may require careful partitioning to prevent supply disturbance from appearing as signal noise. Stable operation also depends on suitable feedback networks and adherence to the layout and compensation guidance in the manufacturer datasheet.
This page combines the LM224DTBR2 ordering information with practical guidance on package compatibility, replacement decisions, analog layout, and application selection. It is intended to help engineers determine whether the four-channel, single-supply amplifier is suitable for a new design and whether a documented alternative can preserve an existing 14-pin TSSOP footprint.
直接替换替代料: LM224DTBR2 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM224DTBR2 (相同外形与封装尺寸) ——差异在于 Package, Number of Amplifier Channels, Product Type.
LM224DTBR2G
✅ 直接替换📋 参考替代料(不在目录中)
LM224DTBG
✅ 直接替换联系询价
查看数据手册 →LM324DTBR2
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM224DTBR2 最大额定值与电气特性
| Number of Amplifier Channels | 4 circuits |
| Operating Supply Range | 3 V to 32 V |
| Supply Type | Single supply |
| Input Type | True differential inputs |
| Product Class | Standard general-purpose operational amplifier |
| 封装 | 14-pin TSSOP |
| 安装类型 | Surface mount |
| 引脚数 | 14 pins |
LM224DTBR2 14-pin tssop 引脚配置指南
LM224DTBR2(14-pin tssop 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM224DTBR2.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM224DTBR2 适用于 6 应用s: Industrial Sensor Conditioning, ADC Input Buffering, Audio Preamplifier and Mixer, Single-Supply Control Circuit, Active Analog Filter, Portable and Battery-Powered Instrumentation.
Industrial Sensor Conditioning
The LM224DTBR2 is suitable for conditioning low-level industrial sensor signals because four channels can provide gain, filtering, and buffering within one 14-pin TSSOP package. A typical signal chain could use a non-inverting stage to raise the sensor voltage, an active low-pass filter to reject noise, and a voltage follower to drive the next circuit. The device operates from a 3 V to 32 V single supply, allowing it to work across low-voltage electronics and higher industrial rails. The designer must keep sensor signals within the input common-mode range and verify that the required output level fits within the specified swing limits.
推荐
ADC Input Buffering
The LM224DTBR2 can provide isolation and gain between a source and an analog-to-digital converter. With four channels, one design may combine a unity-gain input driver, an anti-alias filter, a second gain stage, and an output buffer without requiring four separate packages. Its 3 V to 32 V operating range supports both compact low-voltage systems and broader industrial supply environments. Because this is a general-purpose amplifier rather than a guaranteed rail-to-rail input device, the engineer should calculate the signal's common-mode operating point and confirm source impedance and capacitive loading behavior before finalizing the filter and feedback network.
推荐
Audio Preamplifier and Mixer
The LM224DTBR2 can implement several stages in a small audio preamplifier or passive mixer, including input amplification, summing, and output buffering. Its four independent channels reduce package count and can shorten the analog path on a space-constrained board. The single-supply operation from 3 V to 32 V permits the circuit to share a system rail, although the usable signal swing remains constrained by the output limits. For microphone or line-level inputs, the source should be referenced to the mid-supply point where necessary, and the designer should verify gain, bandwidth, slew-rate, and output-loading requirements against the intended audio spectrum.
推荐
Single-Supply Control Circuit
The LM224DTBR2 is well suited to general-purpose control boards that accept analog command or feedback signals referenced to ground. Its four channels can form error amplifiers, comparators around a reference, current or voltage buffers, and output drivers for control elements. The 3 V to 32 V supply range allows use in systems whose control rail differs from a 5 V logic rail. Because the amplifier is not specified as a rail-to-rail input part, the common-mode range must be checked throughout the command range. Feedback components should also be selected for the intended closed-loop gain and stability with the output load represented by the actual control circuit.
推荐
Active Analog Filter
The four channels of the LM224DTBR2 can implement active low-pass, high-pass, or band-pass sections around a sensor or measurement chain. Two channels can form a second-order filter section, while the remaining channels can provide input and output buffering or another signal-conditioning stage. This consolidation is valuable in compact instrumentation where board area is limited. The resistor and capacitor values should be selected from the desired corner frequency and closed-loop gain, then checked for acceptable step response and noise. The common package supply makes it important to route high-current feedback and output currents away from sensitive input traces to reduce coupling between channels.
推荐
Portable and Battery-Powered Instrumentation
The LM224DTBR2 can serve as the analog core in portable instrumentation when the system operates from a 3 V or higher single rail. Four channels provide useful flexibility for sensor amplification, filtering, and buffering while the 14-pin TSSOP supports compact surface-mount layouts. Low-voltage operation does not make every signal automatically usable: inputs below ground are outside a simple single-supply design unless the source is biased into the valid common-mode window. A battery-powered design should also verify the amplifier's supply current and output-current behavior against the available power budget, because general-purpose specifications do not guarantee low-power operation comparable to purpose-built micropower amplifiers.
推荐
推荐产品汇总
工程参考数据: LM224DTBR2 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM224DTBR2G | LM224DTB | LM324DTBR2 |
|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi |
| Package | TSSOP-14 | TSSOP-14 | TSSOP-14 | TSSOP-14 |
| Amplifier Channels | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Product Class | Standard general-purpose amplifier | Standard general-purpose amplifier | Standard general-purpose amplifier | Standard general-purpose amplifier |
| Pin Count | 14 pins | 14 pins | 14 pins | 14 pins |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
关键差异点
- Four independent channels in a compact 14-pin package (对比 LM224DTBR2G)
- Single-supply range spans 3 V to 32 V (对比 LM224DTB)
- LM224-family selection retains industrial-grade positioning (对比 LM324DTBR2)
设计说明
Place the supply decoupling capacitor immediately adjacent to the package power pin, and connect the package ground pin to a low-impedance ground plane. Keep the four channels' input and feedback traces short, particularly when they carry signals far below the supply rail. Because all channels share internal supply connections, route output-current paths and capacitor return currents so they do not share narrow traces with sensitive input returns. Follow the exact capacitor and copper recommendations in the manufacturer datasheet for the chosen TSSOP layout.
Do not assume that a 3 V to 32 V supply rating permits input and output signals to cover the full rail-to-rail range. Check the input common-mode window and output swing for the actual supply voltage, output load, and temperature. Inputs near ground can require an artificial bias point when no negative supply is present. Also verify the gain-bandwidth, slew-rate, output-current, and stability requirements of each closed-loop configuration before using all four channels simultaneously.
Give each amplifier an independent feedback network and keep each input node physically separated from high-current output pins on the same package. If one channel drives a low-impedance load while another measures a small signal, route the load return directly to the supply ground and preserve a quiet analog ground region for the measurement channel. Add filtering and bypassing at the board boundary when long cables or switching supplies enter the board. This partitioning reduces channel-to-channel coupling that is not visible from the block diagram.
Size feedback resistors and compensation capacitors for the actual gain, source impedance, load capacitance, and required bandwidth. A low-value feedback network can increase capacitive loading and risk stability problems, while excessively high values can increase noise and offset sensitivity. Simulate the intended topology with the load connected, then measure input-referred noise and settling behavior on the assembled board. Keep sensitive summing nodes short and use a nearby ground reference for every feedback component.
合规信息
Specific compliance declarations and qualification status must be confirmed using the exact LM224DTBR2 ordering information and the current manufacturer documentation.