Texas Instruments

LM258ADRE4 - Dual 700 kHz Op Amp in 8-SOIC | Texas Instruments

料号: LM258ADRE4 ✓ 量产中
Single supply or split supply Vdss 0.7 mA per amplifier Id 8-SOIC, 0.154 inch body width, 3.90 mm width Package Internal Speed
最小起订量: 1 |

LM258ADRE4 概述

The Texas Instruments LM258ADRE4 is a dual general-purpose operational amplifier with two independent, internally frequency-compensated amplifiers, a 700 kHz gain-bandwidth product, and an 8-SOIC package. The device accepts single or split supplies, supports a 32 V maximum total supply voltage, and can operate with an input common-mode range that includes ground. These characteristics make it suitable for industrial control, instrumentation, sensor conditioning, and low-cost general-purpose analog signal paths.

An operational amplifier is an analog integrated circuit that provides high open-loop gain and stable closed-loop behavior when connected with negative feedback. The LM258 belongs to the broader hierarchy of operational amplifier, voltage-feedback amplifier IC, analog IC, and semiconductor. Unlike rail-to-rail precision amplifiers, the LM258 relies on conventional bipolar input and output stages, making it appropriate where moderate input offset, output swing, and supply-current requirements are acceptable.

Key features include two amplifier channels in one 8-SOIC package, internal frequency compensation, a typical gain-bandwidth product of 700 kHz, and operation from a single supply or split supplies. According to the manufacturer datasheet, the typical input offset voltage is 2 mV, typical input offset current is 2 nA, typical input bias current is 15 nA, and typical supply-current drain is 0.7 mA per amplifier. The common-mode input range includes ground, which is useful for sensing signals near the lower supply rail.

The LM258AD uses two internal voltage-compensated amplifiers designed for general-purpose operation. Internal compensation removes the need for an external dominant-pole capacitor in typical closed-loop configurations. Because the amplifier is not rail-to-rail at its inputs or outputs, output-headroom and common-mode calculations must be completed for the actual supply voltage, load current, output waveform, and connected feedback network.

Typical uses include low-side current measurement, sensor amplification, buffered references, audio and communications interfaces, and industrial analog modules. Its 700 kHz bandwidth supports moderate-frequency feedback loops, while the dual-channel arrangement reduces component count when two independent amplifier functions are required.

PCB design should prioritize short feedback traces, clean grounding, and decoupling close to the supply pins. Place the supply-bypass capacitor between the V+ and ground connections at the device, keep high-impedance input nodes away from switching-current paths, and verify common-mode and output-swing margins across the full operating range.

This page combines package and electrical characteristics with drop-in replacement guidance, application-specific engineering notes, and a parameter-by-parameter comparison. It also highlights verification points for supply voltage, temperature grade, pin compatibility, and manufacturer qualification before a component is approved for production.

直接替换替代料: LM258ADRE4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: LM258ADRE4 (相同外形与封装尺寸) ——差异在于 Amplifier Type, Package, Number of Channels, Operating Temperature, Slew Rate.

STMicroelectronics
Amplifier Type: Dual low-power operational amplifier
Package: 8-pin SOIC
Operating Temperature: -40 C to +105 C
对比 LM258ADRE4 →
Texas Instruments
Amplifier Type: General Purpose
Package: 8-SOIC (D)
Number of Channels: 2
对比 LM258ADRE4 →

LM258DRG3

✅ 直接替换
📦 8-SOIC
Same dual-amplifier and 700 kHz architecture; ordering suffix changes qualification or grade details that require datasheet confirmation

📋 参考替代料(不在目录中)

LM258DT

✅ 直接替换
STMicroelectronics
📦 8-SOIC
Dual low-power operational amplifier · 2 amplifiers · 2 circuits · 3 V to 30 V · 1.1 MHz · 0.6 V/us · 100 dB · 500 uA

联系询价

查看数据手册 →

TSH22IDT

✅ 直接替换
📦 8-SOIC
Same 8-SOIC dual-op-amp layout, with possible differences in supply current, input bias current, offset, and slew rate

📋 参考替代料(不在目录中)

TSB7192IDT

✅ 直接替换
📦 8-SOIC
Pin-compatible 8-SOIC dual amplifier with different input-stage, supply, and dynamic-performance characteristics

📋 参考替代料(不在目录中)

LM2904DR

✅ 直接替换
Texas Instruments
📦 8-SOIC
2 · 3 V to 26 V · ±1.5 V to ±13 V · 700 kHz · 0.3 V/us · 2 mV (typical) · 500 uA (typical) · 0.7 mA (typical)

联系询价

查看数据手册 →

RC4558

✅ 直接替换
📦 8-SOIC
Comparable dual-amplifier 8-SOIC format, with different offset, bias-current, bandwidth, and supply-current limits

📋 参考替代料(不在目录中)

LM258ADRE4 最大额定值与电气特性

Amplifier Type Dual general-purpose operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 700 kHz
Supply Configuration Single supply or split supply
Maximum Total Supply Voltage 32 V
Nominal Split-Supply Rating ±16 V
Typical Supply-Current Drain 0.7 mA per amplifier
Typical Input Offset Voltage 2 mV
Typical Input Offset Current 2 nA
Typical Input Bias Current 15 nA
Common-Mode Input Range Includes ground
Differential Input Voltage Range 32 V, equal to maximum-rated supply
Frequency Compensation Internal
封装 8-SOIC, 0.154 inch body width, 3.90 mm width
安装类型 Surface mount

LM258ADRE4 引脚配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
引脚 1 OUT1 — Amplifier 1 output
引脚 2 IN1- — Amplifier 1 inverting input
引脚 3 IN1+ — Amplifier 1 non-inverting input
引脚 4 V- — Negative supply or ground connection
引脚 5 IN2+ — Amplifier 2 non-inverting input
引脚 6 IN2- — Amplifier 2 inverting input
引脚 7 OUT2 — Amplifier 2 output
引脚 8 V+ — Positive supply connection

典型应用

LM258ADRE4 适用于 6 应用s: Low-Side Current Sensing, Industrial Sensor Conditioning, Audio Signal Conditioning, Communications Interface Buffering, Buffered Voltage Reference, Test and Measurement Front End.

⚡

Low-Side Current Sensing

The LM258ADRE4 fits low-side current sensing because its input common-mode range includes ground, allowing a small shunt voltage to be measured above the lower supply rail. The dual 700 kHz channels can amplify the shunt signal and provide a second buffered or gain stage. Design around the typical 2 mV input offset and 15 nA input bias current, since those values contribute to error near the shunt’s low end. Check the shunt’s common-mode voltage and the amplifier output swing at the selected supply voltage.

🏭

Industrial Sensor Conditioning

LM258ADRE4 is suitable for conditioning industrial sensor outputs when the signal lies within the classic common-mode range and modest bandwidth is sufficient. Its internally compensated dual configuration can amplify one sensor channel and buffer or level-shift another without adding external compensation capacitors. The approximately 700 kHz gain-bandwidth product is appropriate for many pressure, temperature, and position sensors, but long sensor cables and fast transients may require filtering. Verify input bias-current error and provide local supply decoupling.

🎧

Audio Signal Conditioning

The LM258ADRE4 can serve as a general-purpose audio preamplifier or line-stage buffer in cost-sensitive equipment. Two independent channels permit left and right signal processing in one 8-SOIC package, while the 700 kHz gain-bandwidth product comfortably covers the audio band. Gain and bandwidth are inversely related, so higher closed-loop gain reduces usable bandwidth and can increase distortion at large signal levels. The non-rail-to-rail output requires headroom, and the input should be AC-coupled when appropriate.

🌐

Communications Interface Buffering

LM258ADRE4 can buffer slow differential or single-ended communication signals in industrial and embedded interfaces. The dual internal amplifiers permit receive-side filtering and transmit-side buffering in a compact package, and the common-mode range includes ground simplifies interfacing with sensors or logic at the bottom of the supply range. Its typical 15 nA input bias current helps preserve weak-source accuracy. Confirm maximum signal bandwidth, output loading, slew-rate margin, and ground-offset behavior at the intended data rate.

🔧

Buffered Voltage Reference

A dual op amp can create a buffered reference or provide two outputs for downstream analog circuits. LM258ADRE4 is appropriate when the reference current is modest and the required output impedance must be much lower than the passive reference source. The typical 2 mV input offset translates directly into output uncertainty in a unity-gain buffer, so reference accuracy and resistor matching still matter. Confirm output-current capability, capacitive-load stability, and supply headroom for the selected reference voltage.

📺

Test and Measurement Front End

LM258ADRE4 can provide adjustable gain and signal conditioning ahead of an ADC in a general-purpose measurement instrument. Its dual channels allow differential or dual-ended measurements, while internal frequency compensation simplifies conventional inverting and non-inverting stages. The 700 kHz bandwidth supports moderate-frequency measurements but is not intended for high-speed instrumentation. Use resistor networks with suitable matching, account for input offset and bias current, and verify that the ADC input range remains within the amplifier output swing.

What are the key specifications of LM258ADRE4 that engineers should know?
The LM258ADRE4 is a dual, internally compensated general-purpose operational amplifier with a 700 kHz gain-bandwidth product in an 8-SOIC package. According to the manufacturer datasheet, it supports single or split supplies up to 32 V total, has a typical input offset voltage of 2 mV, and draws approximately 0.7 mA per amplifier. Its input common-mode range includes ground, making it useful for many single-supply sensing and control circuits.
What is the operating voltage of LM258ADRE4?
The LM258ADRE4 supports single-supply or split-supply operation with a maximum total supply voltage of 32 V. The commonly specified split-supply operating point is ±16 V, although the exact minimum supply voltage should be confirmed from the manufacturer datasheet for the selected temperature grade. The device also requires an input common-mode voltage at least 1.5 V below the positive supply for correct operation.
Where can I download the LM258ADRE4 datasheet PDF?
The LM258ADRE4 manufacturer datasheet can be accessed through the Texas Instruments documentation listing or through the datasheet result linked on this page. The document describes the dual-amplifier architecture, electrical characteristics, typical applications, pin configuration, and ordering information. Use the manufacturer PDF for final supply limits, temperature ratings, test conditions, and package drawings before releasing a production design.
Where can I find the LM258ADRE4 pinout and SOIC-8 package drawing?
The LM258ADRE4 uses an 8-SOIC pin arrangement with two complete operational amplifiers. According to the manufacturer datasheet, pin 1 is output 1, pins 2 and 3 are the inverting and non-inverting inputs for amplifier 1, pin 4 is ground, pins 5 and 6 are the non-inverting and inverting inputs for amplifier 2, pin 7 is output 2, and pin 8 is the positive supply. Verify the top-view numbering against the package drawing.
Is LM258ADRE4 suitable for single 5 V sensor-conditioning applications?
The LM258ADRE4 can be used in a single 5 V circuit when the signal and desired output remain within its common-mode and output-swing limits. Its common-mode input range includes ground, which helps with sensors whose output approaches 0 V. However, the output cannot necessarily swing rail to rail, so check the output voltage against the load and required logic levels while allowing adequate headroom.
LM258ADRE4 vs LM258ADR: which part should be selected?
LM258ADRE4 and LM258ADR belong to the same LM258 family and use the same 8-SOIC architecture. The LM258ADRE4 ordering code includes the manufacturer’s E4 temperature-grade suffix, while LM258ADR represents another ordering configuration. Both offer two internally compensated amplifiers and approximately 700 kHz bandwidth. Confirm the exact temperature range, qualification, and packaging suffix against the manufacturer ordering table before treating one as interchangeable.
What is the best drop-in replacement for LM258ADRE4?
The closest same-manufacturer replacement is the LM258 family variant with the same 8-SOIC footprint and dual-amplifier configuration, provided its temperature grade and ordering suffix meet the design requirements. Cross-family parts such as LM2904, RC4558, TSH22IDT, and TSB7192IDT may offer similar SOIC-8 functionality, but input offset, bias current, common-mode range, output swing, and compensation must be compared before substitution. Review the pinout and worst-case specifications.
Can TSH22IDT replace LM258ADRE4 without PCB changes?
TSH22IDT is identified as an LM258DT-family alternative in an 8-pin SOIC and may preserve the standard dual-op-amp footprint. It is not automatically a functional replacement because supply range, input bias current, offset voltage, output swing, noise, and slew rate can differ. Use TSH22IDT only after comparing the manufacturer datasheets and confirming that its pin functions match every populated PCB location.
Is LM258ADRE4 the same as LM2904?
No. LM258ADRE4 and LM2904 belong to related general-purpose dual-op-amp families, but their temperature grades and detailed electrical limits can differ. LM2904 is commonly associated with an industrial temperature range, while LM258ADRE4 carries the E4 grade designation. Both may use an 8-SOIC outline and similar amplifier functions, but input bias current, offset voltage, supply-current draw, and common-mode limits must be checked before substitution.
How should I calculate common-mode and output-swing limits for LM258ADRE4?
Begin with the actual positive and negative supply voltages and compare the input signal range with the common-mode limits in the manufacturer datasheet. The LM258 input range includes ground, but operation still requires at least 1.5 V of headroom below the positive supply. At the output, calculate the maximum load current and verify the resulting voltage drop and swing limits, especially when driving a sensor, ADC input, or transistor logic stage.
What decoupling and layout practice should be used with LM258ADRE4?
Place a supply-bypass capacitor physically between pin 8, V+, and ground, with its ground connection following the shortest practical return path to pin 4. Keep feedback components close to their associated pins, route input signals away from switching nodes, and maintain a quiet ground reference. Because high-impedance input bias current is only typically 15 nA, even a small leakage path through board contamination can affect the measured voltage.
Is LM258ADRE4 RoHS compliant and qualified for automotive use?
The RoHS, REACH, and automotive-qualification status must be confirmed from the manufacturer’s current product and material declarations. LM258ADRE4’s E4 ordering suffix identifies a temperature-grade variant, but the suffix alone does not establish AEC-Q100 qualification. Do not infer automotive approval solely from the family name or package code; request the applicable manufacturer compliance and qualification documentation.
Where can I buy LM258ADRE4 and check its lead time?
Use the Request a Quote form on this page to request LM258ADRE4 availability, current lead time, and a quotation for the required quantity and packaging. The form is the appropriate channel for volume sourcing and schedule confirmation because inventory and commercial terms can change quickly. State the exact LM258ADRE4 ordering code and the required reel, tray, or other delivery format when submitting the request.
What is the price of LM258ADRE4?
The current commercial price for LM258ADRE4 is best obtained through the Request a Quote form on this page. The form allows quantity, delivery format, and project requirements to be considered without presenting a static quotation that may quickly become obsolete. Submit the exact 8-SOIC tape-and-reel part number and state the required purchase quantity for an actionable response.
Is LM258ADRE4 in stock?
Current LM258ADRE4 inventory should be confirmed through the Request a Quote form on this page. Distributor availability can vary by reel quantity, factory allocation, and regional logistics, so a generic product-page listing is not a reliable stock commitment. State the required order quantity and target delivery date when requesting a quotation and confirmation.

工程参考数据: LM258ADRE4 ——对比、设计指导和合规信息。

选型指南

Choose LM258ADRE4 for general-purpose dual-amplifier designs that need approximately 700 kHz bandwidth, internal frequency compensation, operation from a single or split supply, and an input common-mode range that includes ground. It is particularly useful when one 8-SOIC can provide two independent channels and the application does not require rail-to-rail input or output behavior. Consider LM2904 when its temperature grade and input-bias characteristics better match the design. Consider LM258DRG3 when its ordering suffix and qualification details are preferable, but verify the manufacturer ordering table. LM258DT, TSH22IDT, and TSB7192IDT may preserve the SOIC-8 footprint, yet each requires comparison of offset voltage, bias current, supply limits, output swing, slew rate, and exact pin functions. Do not substitute any candidate solely because all parts use an 8-SOIC outline; confirm the top-view pinout and worst-case operating conditions before production release.

与替代料对比

参数 本产品 LM258DRG3 LM258DT TSH22IDT TSB7192IDT LM2904
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Brand Texas Instruments Texas Instruments STMicroelectronics STMicroelectronics STMicroelectronics Texas Instruments
Number of Amplifiers 2 2 2 2 2 2

关键差异点

  • Two internally compensated channels in one 8-SOIC package (对比 LM2904)
  • Consistent 700 kHz general-purpose bandwidth (对比 TSB7192IDT)
  • Input common-mode range includes ground (对比 TSH22IDT)

设计说明

Place the supply-bypass capacitor between pins 8 and 4 and connect it to the quietest available ground return. Keep the capacitor, amplifier output, and feedback components close to the SOIC to minimize trace inductance and high-frequency impedance. For dual-amplifier layouts, avoid sharing a narrow ground path between the two channels when low-level signals are present, because shared supply and ground impedance can convert output current into input-referred disturbance.

Account for the 2 mV typical input offset and 15 nA typical input bias current when sizing source impedances and precision resistors. Bias-current error is approximately input bias current multiplied by total source resistance at each input, while resistor mismatch directly affects closed-loop gain. Use matched networks for differential gains and keep high-impedance input traces short, clean, and guarded against leakage from humidity, flux residue, and nearby switching nodes.

Do not assume rail-to-rail input or output behavior. The input must remain at least 1.5 V below the positive supply, and the output requires headroom for the load and output-current conditions. The differential input range also cannot exceed the maximum-rated supply. These limitations are especially important in 5 V systems designed to use the full logic range or in battery-powered circuits whose supply falls during operation.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

Compliance and qualification information was not explicitly established in the manufacturer or distributor result text. The E4 ordering suffix identifies a grade designation but does not by itself establish AEC-Q100 qualification. Confirm the current manufacturer declarations before procurement.

数据核验日期: 2026-11-20 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

LM258ADRE4 datasheet LM258ADRE4 datasheet pdf LM258ADRE4 pinout LM258ADRE4 SOIC-8 pinout LM258ADRE4 specifications LM258ADRE4 700 kHz LM258ADRE4 replacement LM258ADRE4 equivalent LM258ADRE4 vs LM2904 LM258ADRE4 price LM258ADRE4 stock Texas Instruments LM258ADRE4 LM258ADRE4 single supply LM258ADRE4 sensor conditioning

相关元器件 & 术语

Texas Instruments LM258ADRE4 LM258DRG3 LM258DT TSH22IDT TSB7192IDT LM2904 RC4558 dual operational amplifier operational amplifier IC voltage-feedback amplifier analog integrated circuit semiconductor single-supply operation split-supply operation frequency compensation gain-bandwidth product common-mode input voltage range input offset voltage input bias current 8-SOIC SOIC family surface-mount package industrial control sensor conditioning
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情