LM258ADRE4 - Dual 700 kHz Op Amp in 8-SOIC | Texas Instruments
MPN: LM258ADRE4 ✓ פעילLM258ADRE4 סקירה
An operational amplifier is an analog integrated circuit that provides high open-loop gain and stable closed-loop behavior when connected with negative feedback. The LM258 belongs to the broader hierarchy of operational amplifier, voltage-feedback amplifier IC, analog IC, and semiconductor. Unlike rail-to-rail precision amplifiers, the LM258 relies on conventional bipolar input and output stages, making it appropriate where moderate input offset, output swing, and supply-current requirements are acceptable.
Key features include two amplifier channels in one 8-SOIC package, internal frequency compensation, a typical gain-bandwidth product of 700 kHz, and operation from a single supply or split supplies. According to the manufacturer datasheet, the typical input offset voltage is 2 mV, typical input offset current is 2 nA, typical input bias current is 15 nA, and typical supply-current drain is 0.7 mA per amplifier. The common-mode input range includes ground, which is useful for sensing signals near the lower supply rail.
The LM258AD uses two internal voltage-compensated amplifiers designed for general-purpose operation. Internal compensation removes the need for an external dominant-pole capacitor in typical closed-loop configurations. Because the amplifier is not rail-to-rail at its inputs or outputs, output-headroom and common-mode calculations must be completed for the actual supply voltage, load current, output waveform, and connected feedback network.
Typical uses include low-side current measurement, sensor amplification, buffered references, audio and communications interfaces, and industrial analog modules. Its 700 kHz bandwidth supports moderate-frequency feedback loops, while the dual-channel arrangement reduces component count when two independent amplifier functions are required.
PCB design should prioritize short feedback traces, clean grounding, and decoupling close to the supply pins. Place the supply-bypass capacitor between the V+ and ground connections at the device, keep high-impedance input nodes away from switching-current paths, and verify common-mode and output-swing margins across the full operating range.
This page combines package and electrical characteristics with drop-in replacement guidance, application-specific engineering notes, and a parameter-by-parameter comparison. It also highlights verification points for supply voltage, temperature grade, pin compatibility, and manufacturer qualification before a component is approved for production.
חלופות תחליף ישיר עבור LM258ADRE4 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LM258ADRE4 (אותו גורם צורה וטביעת רגל) — שונים ב Amplifier Type, Package, Number of Channels, Operating Temperature, Slew Rate.
LM258DRG3
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LM258DT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TSH22IDT
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TSB7192IDT
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LM2904DR
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←RC4558
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LM258ADRE4 דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 700 kHz |
| Supply Configuration | Single supply or split supply |
| Maximum Total Supply Voltage | 32 V |
| Nominal Split-Supply Rating | ±16 V |
| Typical Supply-Current Drain | 0.7 mA per amplifier |
| Typical Input Offset Voltage | 2 mV |
| Typical Input Offset Current | 2 nA |
| Typical Input Bias Current | 15 nA |
| Common-Mode Input Range | Includes ground |
| Differential Input Voltage Range | 32 V, equal to maximum-rated supply |
| Frequency Compensation | Internal |
| מארז | 8-SOIC, 0.154 inch body width, 3.90 mm width |
| סוג הרכבה | Surface mount |
תצורת פינים של LM258ADRE4
| פין 1 | OUT1 — Amplifier 1 output |
| פין 2 | IN1- — Amplifier 1 inverting input |
| פין 3 | IN1+ — Amplifier 1 non-inverting input |
| פין 4 | V- — Negative supply or ground connection |
| פין 5 | IN2+ — Amplifier 2 non-inverting input |
| פין 6 | IN2- — Amplifier 2 inverting input |
| פין 7 | OUT2 — Amplifier 2 output |
| פין 8 | V+ — Positive supply connection |
יישומים טיפוסיים
LM258ADRE4 מתאים עבור 6 יישוםs: Low-Side Current Sensing, Industrial Sensor Conditioning, Audio Signal Conditioning, Communications Interface Buffering, Buffered Voltage Reference, Test and Measurement Front End.
Low-Side Current Sensing
The LM258ADRE4 fits low-side current sensing because its input common-mode range includes ground, allowing a small shunt voltage to be measured above the lower supply rail. The dual 700 kHz channels can amplify the shunt signal and provide a second buffered or gain stage. Design around the typical 2 mV input offset and 15 nA input bias current, since those values contribute to error near the shunt’s low end. Check the shunt’s common-mode voltage and the amplifier output swing at the selected supply voltage.
מומלץ
Industrial Sensor Conditioning
LM258ADRE4 is suitable for conditioning industrial sensor outputs when the signal lies within the classic common-mode range and modest bandwidth is sufficient. Its internally compensated dual configuration can amplify one sensor channel and buffer or level-shift another without adding external compensation capacitors. The approximately 700 kHz gain-bandwidth product is appropriate for many pressure, temperature, and position sensors, but long sensor cables and fast transients may require filtering. Verify input bias-current error and provide local supply decoupling.
מומלץ
Audio Signal Conditioning
The LM258ADRE4 can serve as a general-purpose audio preamplifier or line-stage buffer in cost-sensitive equipment. Two independent channels permit left and right signal processing in one 8-SOIC package, while the 700 kHz gain-bandwidth product comfortably covers the audio band. Gain and bandwidth are inversely related, so higher closed-loop gain reduces usable bandwidth and can increase distortion at large signal levels. The non-rail-to-rail output requires headroom, and the input should be AC-coupled when appropriate.
מומלץ
Communications Interface Buffering
LM258ADRE4 can buffer slow differential or single-ended communication signals in industrial and embedded interfaces. The dual internal amplifiers permit receive-side filtering and transmit-side buffering in a compact package, and the common-mode range includes ground simplifies interfacing with sensors or logic at the bottom of the supply range. Its typical 15 nA input bias current helps preserve weak-source accuracy. Confirm maximum signal bandwidth, output loading, slew-rate margin, and ground-offset behavior at the intended data rate.
מומלץ
Buffered Voltage Reference
A dual op amp can create a buffered reference or provide two outputs for downstream analog circuits. LM258ADRE4 is appropriate when the reference current is modest and the required output impedance must be much lower than the passive reference source. The typical 2 mV input offset translates directly into output uncertainty in a unity-gain buffer, so reference accuracy and resistor matching still matter. Confirm output-current capability, capacitive-load stability, and supply headroom for the selected reference voltage.
מומלץ
Test and Measurement Front End
LM258ADRE4 can provide adjustable gain and signal conditioning ahead of an ADC in a general-purpose measurement instrument. Its dual channels allow differential or dual-ended measurements, while internal frequency compensation simplifies conventional inverting and non-inverting stages. The 700 kHz bandwidth supports moderate-frequency measurements but is not intended for high-speed instrumentation. Use resistor networks with suitable matching, account for input offset and bias current, and verify that the ADC input range remains within the amplifier output swing.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LM258ADRE4 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LM258DRG3 | LM258DT | TSH22IDT | TSB7192IDT | LM2904 |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Texas Instruments | Texas Instruments | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
מבדילים עיקריים
- Two internally compensated channels in one 8-SOIC package (לעומתLM2904)
- Consistent 700 kHz general-purpose bandwidth (לעומתTSB7192IDT)
- Input common-mode range includes ground (לעומתTSH22IDT)
הערות תכנון
Place the supply-bypass capacitor between pins 8 and 4 and connect it to the quietest available ground return. Keep the capacitor, amplifier output, and feedback components close to the SOIC to minimize trace inductance and high-frequency impedance. For dual-amplifier layouts, avoid sharing a narrow ground path between the two channels when low-level signals are present, because shared supply and ground impedance can convert output current into input-referred disturbance.
Account for the 2 mV typical input offset and 15 nA typical input bias current when sizing source impedances and precision resistors. Bias-current error is approximately input bias current multiplied by total source resistance at each input, while resistor mismatch directly affects closed-loop gain. Use matched networks for differential gains and keep high-impedance input traces short, clean, and guarded against leakage from humidity, flux residue, and nearby switching nodes.
Do not assume rail-to-rail input or output behavior. The input must remain at least 1.5 V below the positive supply, and the output requires headroom for the load and output-current conditions. The differential input range also cannot exceed the maximum-rated supply. These limitations are especially important in 5 V systems designed to use the full logic range or in battery-powered circuits whose supply falls during operation.
מידע על תאימות
Compliance and qualification information was not explicitly established in the manufacturer or distributor result text. The E4 ordering suffix identifies a grade designation but does not by itself establish AEC-Q100 qualification. Confirm the current manufacturer declarations before procurement.