LM2902KNSG4 - Quad 26V 1.2MHz Op-Amp SOIC-14 | Texas Instruments
料号: LM2902KNSG4 ✓ 量产中LM2902KNSG4 概述
An operational amplifier is a high-gain voltage amplifier with differential inputs and a single-ended output, forming the foundational building block of analog signal conditioning. Quad op-amps such as the LM2902K family integrate four such amplifiers on one die, sharing supply rails to reduce board area and cost in multi-channel analog front ends, within the broader hierarchy of linear ICs and analog signal processing semiconductors.
Key features of the LM2902KNSG4 include wide supply ranges of 3 V to 26 V single-supply (or +/-13 V dual supply per the LM2902K family data), a low supply-current drain of typically 0.8 mA that is largely independent of supply voltage, and an input common-mode range that extends to ground on single supplies. The K-grade device improves on the base LM2902 with enhanced 2 kV ESD robustness, which the manufacturer lists on the TI LM2902K product page.
Technically, the device uses internally compensated bipolar architecture providing unity-gain stability without external compensation components. The 0.5 V/µs slew rate and 1.2 MHz gain-bandwidth product suit low-to-moderate frequency conditioning: sensor buffering, active filters, comparators, and transducer amplifiers. Differential input voltage ranges and the ability to swing outputs near the negative rail support ground-referenced sensing on single-supply industrial rails.
Typical applications include industrial process-control signal conditioning, automotive sensor interfaces within the -40C to +125C automotive temperature range of the LM2902 family, and consumer audio or instrumentation multi-channel buffers where four matched amplifiers reduce BOM count.
One design consideration: output swing is limited near the positive rail, so set signal headroom below the supply by roughly 1.5 V, or use rail-to-rail output alternatives if full-swing is required. Decouple the shared VCC pin with 0.1 µF close to pin 4.
This page adds value beyond the datasheet with drop-in alternatives, a parameter-by-parameter comparison table, and practical design notes synthesized for engineers evaluating the LM2902KNSG4.
直接替换替代料: LM2902KNSG4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2902KNSG4 (相同外形与封装尺寸) ——差异在于 Package, Supply Configuration, Amplifier Type, Number of Amplifiers, Output Type.
LM2902KNSRG4
✅ 直接替换联系询价
查看数据手册 →LM2902D
✅ 直接替换联系询价
查看数据手册 →LM2902KVDR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM324D
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM2902KNSG4 最大额定值与电气特性
| Amplifier Type | General Purpose |
| Number of Circuits | 4 |
| Gain Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/us |
| Supply Voltage (Single) | Up to 26 V |
| Supply Voltage (Dual) | Up to +/-13 V |
| Supply Current (Typ) | 0.8 mA |
| ESD Rating | 2 kV (improved ESD) |
| 封装 | 14-SOIC (0.209 in, 5.30 mm width) |
| 安装类型 | Surface Mount |
| Packaging | Tube |
| 工作温度范围 | -40C to +125C |
| Manufacturer | Texas Instruments |
LM2902KNSG4 引脚配置
| 引脚 1 | 1OUT — Output of amplifier 1 |
| 引脚 2 | 1IN- — Inverting input of amplifier 1 |
| 引脚 3 | 1IN+ — Non-inverting input of amplifier 1 |
| 引脚 4 | VCC — Positive supply voltage |
| 引脚 5 | 2IN+ — Non-inverting input of amplifier 2 |
| 引脚 6 | 2IN- — Inverting input of amplifier 2 |
| 引脚 7 | 2OUT — Output of amplifier 2 |
| 引脚 8 | 3OUT — Output of amplifier 3 |
| 引脚 9 | 3IN- — Inverting input of amplifier 3 |
| 引脚 10 | 3IN+ — Non-inverting input of amplifier 3 |
| 引脚 11 | VEE/GND — Negative supply or ground (single supply) |
| 引脚 12 | 4IN+ — Non-inverting input of amplifier 4 |
| 引脚 13 | 4IN- — Inverting input of amplifier 4 |
| 引脚 14 | 4OUT — Output of amplifier 4 |
典型应用
LM2902KNSG4 适用于 6 应用s: Industrial Sensor Signal Conditioning, Automotive Body Electronics and Sensor Interfaces, Multi-Channel Active Filter Networks, Comparator and Level-Detection Circuits, Consumer Audio Line-Level Buffering, Power Supply Monitoring and Control Loops.
Industrial Sensor Signal Conditioning
In factory automation and process control, sensors such as pressure transducers, level sensors, and thermocouple front ends produce small differential or single-ended signals referenced to ground. The LM2902KNSG4 fits this role because its input common-mode range includes ground on single supplies, it operates from the 24 V industrial rail directly (26 V maximum), and each of its four channels draws only a fraction of the 0.8 mA total quiescent current. A typical circuit buffers the sensor output with one amplifier as a unity-gain follower, gains a bridge signal with a second channel, filters with a third, and drives an ADC or comparator with the fourth - all from one 14-SOIC device. The trade-off is that outputs swing only to about 1.5 V below the positive rail, so ADC full-scale should be scaled accordingly or the signal conditioned below that headroom.
推荐
Automotive Body Electronics and Sensor Interfaces
Automotive modules - window lifters, seat controllers, coolant and oil-pressure monitors - operate from the 12 V battery rail with transients and harsh ESD exposure. The LM2902KNSG4 suits these systems because the LM2902K family is specified from -40C to +125C, and the K grade adds improved 2 kV ESD robustness against harness-level discharge events. Four internal amplifiers allow one device to buffer multiple sensor inputs and drive indicator comparators, reducing component count on cost-sensitive body boards. Designs typically run the part directly from the battery rail through protection circuitry, using the 1.2 MHz gain-bandwidth for low-frequency sensing tasks. For new automotive platforms requiring formal AEC-Q100 qualification evidence, verify qualification status on the TI LM2902K product page or via the enhanced LM2902KV variant.
推荐
Multi-Channel Active Filter Networks
Anti-aliasing and conditioning filters ahead of ADCs frequently need several second-order or Sallen-Key stages. The LM2902KNSG4 provides four internally compensated, unity-gain-stable amplifiers, so two Sallen-Key second-order sections fit on a single device with predictable phase behavior from the 1.2 MHz gain-bandwidth product. Because gain-bandwidth must be at least 50-100x the filter cutoff frequency for accurate response, this device supports cutoffs up to roughly 10-20 kHz with low Q error - an estimate from the GBW ratio rule of thumb. The 0.5 V/us slew rate limits large-signal handling, so keep filter output amplitudes within the swing headroom of the supply. Running from a 5 V or 24 V single supply with ground-referenced signals is straightforward since the input range includes ground.
推荐
Comparator and Level-Detection Circuits
Battery chargers, over-voltage monitors, and industrial limit alarms need several threshold detectors per board. The LM2902KNSG4 is commonly used as a quad comparator substitute where moderate speed suffices: its differential input stage tolerates a wide input range down to the negative rail, and outputs can sink enough current to drive LEDs or optocoupler inputs through series resistors. Running from the 26 V maximum rail allows direct monitoring of 24 V systems without dividers in some topologies. Designers should add hysteresis with positive feedback resistors because open-loop transition time at 0.5 V/us is slow compared with dedicated comparators, and outputs are not open-collector, so wired-OR configurations are not possible. For 5 V logic interfacing, add a pull-up and clamp or select a true comparator device.
推荐
Consumer Audio Line-Level Buffering
Multi-channel consumer audio equipment - surround preamps, karaoke mixers, powered speakers - uses several line-level buffers, mixers, and volume-stage gain blocks per channel set. The LM2902KNSG4's four matched channels handle left/right buffering plus summing duties on one SOIC-14 device, and the 1.2 MHz gain-bandwidth product is adequate for the full audio band at closed-loop gains up to roughly 20 dB. The 0.8 mA total quiescent draw helps meet standby-power targets, and single-supply operation from 12 V adapters works because the inputs operate at ground-referenced bias through coupling capacitors. Keep gain below the point where 0.5 V/us slew limiting produces distortion at high amplitudes, and bypass the shared VCC pin carefully to prevent inter-channel crosstalk through the supply impedance.
推荐
Power Supply Monitoring and Control Loops
Switching and linear power supplies use op-amps for output-voltage feedback error amplification, over-current sense amplification, and rail supervision. The LM2902KNSG4 fits offline and industrial converters because the LM2902K family tolerates up to 26 V rails - directly compatible with 24 V auxiliary supplies - and its supply current of typically 0.8 mA adds negligible housekeeping loss. One device can implement the voltage-loop error amplifier, an over-current comparator, an undervoltage detector, and a soft-start buffer simultaneously. Layout practice places the error amplifier close to the feedback divider with a direct ground connection to pin 11 to avoid loop instability, and the 1.2 MHz bandwidth suits compensation networks crossing over in the 1-10 kHz range typical of industrial converters.
推荐
推荐产品汇总
工程参考数据: LM2902KNSG4 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2902KNSR | LM2902D | LM324D |
|---|---|---|---|---|
| Package | 14-SOIC (NS, 5.30 mm) | 14-SOIC (NS) - same | 14-SOIC - same footprint | 14-SOIC - same footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Circuits | 4 | 4 | 4 | 4 |
| Gain Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Slew Rate | 0.5 V/us | 0.5 V/us | 0.5 V/us | 0.5 V/us |
| Maximum Supply Voltage | 26 V (single) | 26 V (single) | 26 V (single) | 32 V (single) |
| Supply Current (Typ) | 0.8 mA | 0.8 mA | 0.8 mA | 1.2 mA (typical family figure) |
| ESD Rating | 2 kV (improved) | 2 kV (improved) | standard LM2902 rating | standard LM324 rating |
关键差异点
- Improved 2 kV ESD robustness (对比 LM2902D)
- 100% identical drop-in in reel format (对比 LM2902KNSR)
- Higher voltage rating within the same footprint (对比 LM2902KNSR / LM324D)
设计说明
Decouple the shared VCC pin (pin 4) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus a 1-10 uF bulk capacitor per board region. Because all four amplifier channels share this supply node, supply-borne crosstalk between channels is the most common defect in LM2902 layouts - a mixer channel bleeding into a filter channel traces back to shared supply impedance. In single-supply 24 V systems, verify the 26 V absolute maximum leaves margin for supply transients or add a series regulator or Zener clamp.
Do not rely on the outputs to reach the positive rail. The LM2902KNSG4 output stage cannot swing to VCC; reserve roughly 1.5 V of headroom when setting gain stages. Also avoid using the device as a precision comparator with wired-OR outputs - outputs are push-pull, not open-collector. When interfacing to 5 V or 3.3 V logic from a 24 V rail, add resistive dividers or clamps. Finally, inputs can be damaged if taken more than the datasheet differential limit below VEE when the device is unpowered; check the absolute maximum table in the TI LM2902K datasheet for the exact figure.
Connect the VEE/GND pin (pin 11) directly to a clean analog ground with a short, wide trace; this pin is the return for all four input stages. Keep feedback resistors close to the inverting input pins to minimize stray capacitance that can cause ringing at higher closed-loop gains. For audio or precision channels, group each amplifier's components locally rather than clustering all four channels' inputs together, and route ground under the feedback network as a mini-ground pour to reduce channel-to-channel crosstalk.
合规信息
The G4 suffix denotes TI's RoHS-compliant green package version. REACH, lead-free and halogen-free status should be confirmed against TI environmental documentation.