Texas Instruments

LM2902KNSG4 - Quad 26V 1.2MHz Op-Amp SOIC-14 | Texas Instruments

N.º de pieza: LM2902KNSG4 ✓ Activo
Up to 26 V Vdss 0.8 mA Id 14-SOIC (0.209 in, 5.30 mm width) Package
MOQ: 1 |

LM2902KNSG4 Descripción general

The Texas Instruments LM2902KNSG4 is a quad general-purpose operational amplifier with four independent high-gain, internally frequency-compensated amplifier circuits in a 14-pin SOIC (NS) package rated for a 26 V single supply or dual supplies, delivering a 1.2 MHz gain-bandwidth product.

An operational amplifier is a high-gain voltage amplifier with differential inputs and a single-ended output, forming the foundational building block of analog signal conditioning. Quad op-amps such as the LM2902K family integrate four such amplifiers on one die, sharing supply rails to reduce board area and cost in multi-channel analog front ends, within the broader hierarchy of linear ICs and analog signal processing semiconductors.

Key features of the LM2902KNSG4 include wide supply ranges of 3 V to 26 V single-supply (or +/-13 V dual supply per the LM2902K family data), a low supply-current drain of typically 0.8 mA that is largely independent of supply voltage, and an input common-mode range that extends to ground on single supplies. The K-grade device improves on the base LM2902 with enhanced 2 kV ESD robustness, which the manufacturer lists on the TI LM2902K product page.

Technically, the device uses internally compensated bipolar architecture providing unity-gain stability without external compensation components. The 0.5 V/µs slew rate and 1.2 MHz gain-bandwidth product suit low-to-moderate frequency conditioning: sensor buffering, active filters, comparators, and transducer amplifiers. Differential input voltage ranges and the ability to swing outputs near the negative rail support ground-referenced sensing on single-supply industrial rails.

Typical applications include industrial process-control signal conditioning, automotive sensor interfaces within the -40C to +125C automotive temperature range of the LM2902 family, and consumer audio or instrumentation multi-channel buffers where four matched amplifiers reduce BOM count.

One design consideration: output swing is limited near the positive rail, so set signal headroom below the supply by roughly 1.5 V, or use rail-to-rail output alternatives if full-swing is required. Decouple the shared VCC pin with 0.1 µF close to pin 4.

This page adds value beyond the datasheet with drop-in alternatives, a parameter-by-parameter comparison table, and practical design notes synthesized for engineers evaluating the LM2902KNSG4.

Alternativas directas para LM2902KNSG4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con LM2902KNSG4 (mismo factor de forma y huella) — difiere en Package, Supply Configuration, Amplifier Type, Number of Amplifiers, Output Type.

Texas Instruments
Package: 14-SOIC
Comparar con LM2902KNSG4 →
Texas Instruments
Package: 14-SOIC
Supply Configuration: Single supply or split supply
Output Type: Push-pull
Comparar con LM2902KNSG4 →
Texas Instruments
Package: 14-SO
Supply Configuration: Single or split supply
Number of Amplifiers: 4 circuits
Comparar con LM2902KNSG4 →
Texas Instruments
Package: 14-pin SOIC
Supply Configuration: Single supply or split supply
Amplifier Type: Quad general-purpose operational amplifier
Comparar con LM2902KNSG4 →

LM2902KNSRG4

✅ Sustitución directa
Texas Instruments
📦 14-SOIC (NS)
4 circuits · 26 V · 1.2 MHz · 2 kV · 14-SO · 125 C · AEC-Q100 qualified · <500 V per MIL-STD-883, Method 3015

Consulte el precio

Ver hoja de datos →

LM2902D

✅ Sustitución directa
Texas Instruments
📦 14-SOIC
Quad operational amplifier · 4 · 26 V · 1.2 MHz · 2 mV · Single supply or split supply · Push-pull

Consulte el precio

Ver hoja de datos →

LM2902KVDR

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 14-SOIC
enhanced K-family version with improved ESD and updated specifications; same quad SOIC-14 footprint

📋 Alternativa de referencia (no en el catálogo)

LM324D

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Texas Instruments
📦 14-SOIC
Quad general-purpose operational amplifier · 4 · Four independent high-gain frequency-compensated operational amplifiers · 3 V to 36 V for B versions · Plus or minus 2 mV maximum for BA versions at 25 C · 2 kV HBM for B, BA, and K versions · Internal RF and EMI filter for B and BA versions · Single supply or split supply

Consulte el precio

Ver hoja de datos →

LM224D

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Texas Instruments
📦 14-SOIC
Standard general-purpose operational amplifier · 4 circuits · 14-SOIC · Surface mount

Consulte el precio

Ver hoja de datos →

LM2902KNSG4 Valores máximos y características eléctricas

Amplifier Type General Purpose
Number of Circuits 4
Gain Bandwidth Product 1.2 MHz
Slew Rate 0.5 V/us
Supply Voltage (Single) Up to 26 V
Supply Voltage (Dual) Up to +/-13 V
Supply Current (Typ) 0.8 mA
ESD Rating 2 kV (improved ESD)
Encapsulado 14-SOIC (0.209 in, 5.30 mm width)
Tipo de montaje Surface Mount
Packaging Tube
Rango de temperatura de funcionamiento -40C to +125C
Manufacturer Texas Instruments

Configuración de pines de LM2902KNSG4

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
Pin 1 1OUT — Output of amplifier 1
Pin 2 1IN- — Inverting input of amplifier 1
Pin 3 1IN+ — Non-inverting input of amplifier 1
Pin 4 VCC — Positive supply voltage
Pin 5 2IN+ — Non-inverting input of amplifier 2
Pin 6 2IN- — Inverting input of amplifier 2
Pin 7 2OUT — Output of amplifier 2
Pin 8 3OUT — Output of amplifier 3
Pin 9 3IN- — Inverting input of amplifier 3
Pin 10 3IN+ — Non-inverting input of amplifier 3
Pin 11 VEE/GND — Negative supply or ground (single supply)
Pin 12 4IN+ — Non-inverting input of amplifier 4
Pin 13 4IN- — Inverting input of amplifier 4
Pin 14 4OUT — Output of amplifier 4

Aplicaciones típicas

LM2902KNSG4 es adecuado para 6 aplicacións: Industrial Sensor Signal Conditioning, Automotive Body Electronics and Sensor Interfaces, Multi-Channel Active Filter Networks, Comparator and Level-Detection Circuits, Consumer Audio Line-Level Buffering, Power Supply Monitoring and Control Loops.

🏭

Industrial Sensor Signal Conditioning

In factory automation and process control, sensors such as pressure transducers, level sensors, and thermocouple front ends produce small differential or single-ended signals referenced to ground. The LM2902KNSG4 fits this role because its input common-mode range includes ground on single supplies, it operates from the 24 V industrial rail directly (26 V maximum), and each of its four channels draws only a fraction of the 0.8 mA total quiescent current. A typical circuit buffers the sensor output with one amplifier as a unity-gain follower, gains a bridge signal with a second channel, filters with a third, and drives an ADC or comparator with the fourth - all from one 14-SOIC device. The trade-off is that outputs swing only to about 1.5 V below the positive rail, so ADC full-scale should be scaled accordingly or the signal conditioned below that headroom.

🚗

Automotive Body Electronics and Sensor Interfaces

Automotive modules - window lifters, seat controllers, coolant and oil-pressure monitors - operate from the 12 V battery rail with transients and harsh ESD exposure. The LM2902KNSG4 suits these systems because the LM2902K family is specified from -40C to +125C, and the K grade adds improved 2 kV ESD robustness against harness-level discharge events. Four internal amplifiers allow one device to buffer multiple sensor inputs and drive indicator comparators, reducing component count on cost-sensitive body boards. Designs typically run the part directly from the battery rail through protection circuitry, using the 1.2 MHz gain-bandwidth for low-frequency sensing tasks. For new automotive platforms requiring formal AEC-Q100 qualification evidence, verify qualification status on the TI LM2902K product page or via the enhanced LM2902KV variant.

🔧

Multi-Channel Active Filter Networks

Anti-aliasing and conditioning filters ahead of ADCs frequently need several second-order or Sallen-Key stages. The LM2902KNSG4 provides four internally compensated, unity-gain-stable amplifiers, so two Sallen-Key second-order sections fit on a single device with predictable phase behavior from the 1.2 MHz gain-bandwidth product. Because gain-bandwidth must be at least 50-100x the filter cutoff frequency for accurate response, this device supports cutoffs up to roughly 10-20 kHz with low Q error - an estimate from the GBW ratio rule of thumb. The 0.5 V/us slew rate limits large-signal handling, so keep filter output amplitudes within the swing headroom of the supply. Running from a 5 V or 24 V single supply with ground-referenced signals is straightforward since the input range includes ground.

⚡

Comparator and Level-Detection Circuits

Battery chargers, over-voltage monitors, and industrial limit alarms need several threshold detectors per board. The LM2902KNSG4 is commonly used as a quad comparator substitute where moderate speed suffices: its differential input stage tolerates a wide input range down to the negative rail, and outputs can sink enough current to drive LEDs or optocoupler inputs through series resistors. Running from the 26 V maximum rail allows direct monitoring of 24 V systems without dividers in some topologies. Designers should add hysteresis with positive feedback resistors because open-loop transition time at 0.5 V/us is slow compared with dedicated comparators, and outputs are not open-collector, so wired-OR configurations are not possible. For 5 V logic interfacing, add a pull-up and clamp or select a true comparator device.

🎧

Consumer Audio Line-Level Buffering

Multi-channel consumer audio equipment - surround preamps, karaoke mixers, powered speakers - uses several line-level buffers, mixers, and volume-stage gain blocks per channel set. The LM2902KNSG4's four matched channels handle left/right buffering plus summing duties on one SOIC-14 device, and the 1.2 MHz gain-bandwidth product is adequate for the full audio band at closed-loop gains up to roughly 20 dB. The 0.8 mA total quiescent draw helps meet standby-power targets, and single-supply operation from 12 V adapters works because the inputs operate at ground-referenced bias through coupling capacitors. Keep gain below the point where 0.5 V/us slew limiting produces distortion at high amplitudes, and bypass the shared VCC pin carefully to prevent inter-channel crosstalk through the supply impedance.

🔌

Power Supply Monitoring and Control Loops

Switching and linear power supplies use op-amps for output-voltage feedback error amplification, over-current sense amplification, and rail supervision. The LM2902KNSG4 fits offline and industrial converters because the LM2902K family tolerates up to 26 V rails - directly compatible with 24 V auxiliary supplies - and its supply current of typically 0.8 mA adds negligible housekeeping loss. One device can implement the voltage-loop error amplifier, an over-current comparator, an undervoltage detector, and a soft-start buffer simultaneously. Layout practice places the error amplifier close to the feedback divider with a direct ground connection to pin 11 to avoid loop instability, and the 1.2 MHz bandwidth suits compensation networks crossing over in the 1-10 kHz range typical of industrial converters.

What is the gain bandwidth product of the LM2902KNSG4?
The LM2902KNSG4 has a gain bandwidth product of 1.2 MHz. This figure applies to each of its four internal amplifier circuits and is published in the Texas Instruments LM2902K product family documentation. The 1.2 MHz GBW supports closed-loop gains up to roughly 40 dB while keeping useful bandwidth at audio and low industrial frequencies, making the part suitable for sensor buffering, active RC filters, and multi-channel transducer conditioning in 26 V industrial systems.
What is the maximum supply voltage of the LM2902KNSG4?
The LM2902KNSG4 operates from a single supply of up to 26 V or dual supplies of up to +/-13 V. According to the Texas Instruments LM2902K product page, the family is specified as a 'Quad, 26-V, 1.2-MHz, improved ESD (2 kV) operational amplifier.' The supply-current drain of typically 0.8 mA is largely independent of supply voltage, so quiescent consumption is predictable whether the part runs from 5 V, 12 V, or a 24 V industrial rail.
How many op-amp channels does the LM2902KNSG4 provide?
The LM2902KNSG4 provides four independent operational amplifier circuits in one 14-pin SOIC package. All four amplifiers share the same supply rails (VCC on pin 4 and VEE/GND on pin 11), giving engineers four matched, internally compensated gain stages for multi-channel signal conditioning. Integrating four channels in a single 14-SOIC reduces board area, component count, and channel-to-channel matching errors compared with four single op-amps.
What is the difference between LM2902KNSG4 and LM2902KNSR?
There is no electrical difference; the suffix only changes the packing format. LM2902KNSG4 is supplied in tube packaging, while the R suffix on LM2902KNSR denotes tape-and-reel packaging for automated assembly. Both use the same 14-SOIC (NS) package, the same die, and identical specifications of 1.2 MHz GBW, 0.5 V/µs slew rate, and 26 V maximum supply. Either can replace the other on the same PCB footprint without redesign.
Can LM324 replace LM2902KNSG4?
Yes, in most general-purpose circuits the LM324 is a pin-to-pin drop-in replacement for the LM2902KNSG4, since both are quad op-amps in 14-pin SOIC with identical pinout. The key difference is the maximum supply rating: the LM324 family is rated to 32 V single supply while the LM2902K is rated to 26 V, and temperature ranges differ by grade. Verify the supply voltage, ESD exposure level, and specified temperature range against the LM324 datasheet before substituting in automotive or industrial environments.
What is the best drop-in replacement for LM2902KNSG4?
The best drop-in replacement is LM2902KNSR, the same die in the same 14-SOIC package supplied in tape-and-reel rather than tube. Because it is the identical device with only a packaging-suffix difference, it is a 100% match for footprint and all electrical parameters. Other same-family options include LM2902D and the enhanced LM2902KV; each is pin-compatible in SOIC-14 but you should confirm temperature grade and ESD specification against your design requirements before ordering.
Is the LM2902KNSG4 suitable for automotive applications?
Yes, the LM2902 family is designed with automotive-grade temperature capability, specified from -40C to +125C, which covers under-hood and body-electronics requirements. The K version adds improved 2 kV ESD robustness per the Texas Instruments LM2902K product page, valuable in harsh wiring-harness environments. For new automotive designs requiring formal AEC-Q100 documentation, confirm the specific qualification status on the TI product page or request it through the quote form on this page.
Where can I download the LM2902KNSG4 datasheet PDF?
The LM2902KNSG4 datasheet is available from the Texas Instruments LM2902K product page at ti.com/product/LM2902K, which links the latest datasheet and family documentation covering the LM2902K, LM2902KV, and LM2902KAV variants. Use the manufacturer datasheet as the authoritative reference for DC and AC electrical characteristics, application circuits, and package mechanical drawings before committing a PCB layout.
Where can I find the LM2902KNSG4 pinout?
The LM2902KNSG4 uses the standard quad op-amp SOIC-14 pinout: pin 1 is output 1, pin 2 inverting input 1, pin 3 non-inverting input 1, pin 4 VCC, pins 5-7 channel 2, pins 8-10 channel 3, pin 11 VEE/GND, and pins 12-14 channel 4. This pinout is shared with the entire LM2902/LM324 quad-op-amp family, and the full pin-description table appears in the Texas Instruments LM2902K datasheet.
What is the slew rate of the LM2902KNSG4?
The LM2902KNSG4 has a slew rate of 0.5 V/us. This limits full-scale output transitions to 0.5 V per microsecond, so a 0 V to 24 V step takes about 48 µs to settle. For sine-wave signals, keep the product of frequency and peak amplitude below the slew limit - for example a 20 Vpp signal stays unclipped up to roughly 8 kHz. Applications requiring faster edges should consider a higher-slew op-amp family instead.
What is the LM2902KNSG4 vs LM2902KV - which should I choose?
The LM2902KV is an enhanced K-family version while the LM2902KNSG4 is the standard K-grade quad op-amp; both are quad 1.2 MHz amplifiers in SOIC-14 with pin-compatible footprints. Choose the LM2902KV when your application demands improved ESD performance or the enhanced specifications TI introduced with the KV grade; choose the LM2902KNSG4 when standard K-grade performance at 26 V is sufficient. Check the TI LM2902K datasheet for the exact parameter deltas, particularly ESD rating and offset specifications, before finalizing.
When should I choose the LM2902KNSG4 over a modern rail-to-rail op-amp?
Choose the LM2902KNSG4 when your design runs from a higher voltage single supply up to 26 V, needs four matched general-purpose channels at very low cost, and does not require output swing to the positive rail. Rail-to-rail op-amps typically top out at 5.5 V to 36 V supplies at higher unit cost; the LM2902K's 0.8 mA total quiescent draw and proven industrial track record make it the economical choice for 24 V sensor conditioning, comparators, and active filters where signals stay 1.5 V below the positive rail.
How much power does the LM2902KNSG4 consume?
The LM2902KNSG4 draws a typical supply current of 0.8 mA across all four amplifier channels, and the TI family documentation states this drain is largely independent of supply voltage. At a 24 V industrial supply, total quiescent dissipation is roughly 19 mW (0.8 mA x 24 V) - an estimate from the typical figure - plus any load current driven by the outputs. This makes the device well suited to power-conscious multi-channel designs where four amplifiers must share a modest power budget.
Is LM2902KNSG4 RoHS compliant and lead-free?
The G4 suffix on Texas Instruments part numbers denotes a RoHS-compliant, green package version, and TI lists LM2902KNSG4 among its green parts. For formal confirmation of RoHS, REACH, and lead-free status on your specific date code, consult the environmental compliance documentation linked from the TI LM2902K product page, or submit the Request a Quote form on this page and our team will provide the compliance certificates with the quotation.
What are the key specifications of LM2902KNSG4 that engineers should know?
The key specifications are: four operational amplifier circuits; 1.2 MHz gain-bandwidth product; 0.5 V/us slew rate; 26 V maximum single-supply or +/-13 V dual-supply operation; typical 0.8 mA supply current independent of supply voltage; improved 2 kV ESD rating; -40C to +125C operating range; and a 14-pin SOIC package 5.30 mm wide supplied in tubes. Together these define a low-cost, robust quad op-amp for industrial and automotive analog signal conditioning up to 26 V rails.
Where to buy LM2902KNSG4 online?
You can request LM2902KNSG4 directly through the Request a Quote form on this XAIPART product page. Submit your required quantity and delivery schedule and our sourcing team responds with current stock, pricing, and lead time. Because commercial availability for this industrial-grade quad op-amp changes frequently, requesting a quote is the fastest way to obtain firm, up-to-date supply terms rather than relying on static listings.
What is the lead time and packaging for LM2902KNSG4?
The LM2902KNSG4 ships in tube packaging, with each tube containing devices in the 14-SOIC (5.30 mm width) package. Current lead time is to be confirmed because availability of this industrial op-amp varies with demand; submit the Request a Quote form on this page for the firm lead time associated with your quantity. For automated pick-and-place production lines, ask about tape-and-reel supply - the same die is offered as LM2902KNSR in reel format.
What is the best STMicroelectronics equivalent for LM2902KNSG4?
A true same-package STMicroelectronics equivalent is a quad op-amp in SOIC-14 with matching supply and bandwidth ratings; candidates from the TS974 low-power quad family are commonly evaluated against the LM2902KNSG4. Before substituting across brands, verify the four checks that matter: pin-to-pin pinout compatibility, maximum supply voltage (the LM2902KNSG4 is 26 V single supply), gain-bandwidth (1.2 MHz here), and temperature range (-40C to +125C). Request the comparison datasheets via the quote form on this page to confirm.
Is the LM2902KNSG4 the same as the LM2902D?
The LM2902KNSG4 and LM2902D come from the same LM2902 quad op-amp family and share the same four-channel architecture and SOIC-14 footprint, but they are different grades: the K version adds improved 2 kV ESD robustness and K-family specification enhancements that the base LM2902D does not carry. Both are pin-compatible drop-ins for general-purpose use; select the KNSG4 when ESD robustness or K-grade parameters are required by your environment, such as industrial or automotive signal conditioning.

Datos de referencia de ingeniería para LM2902KNSG4 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the LM2902KNSG4 when you need a proven, low-cost quad general-purpose op-amp on a 24 V industrial or 12 V automotive rail with improved 2 kV ESD robustness and tube packaging for prototyping or low-volume assembly. Choose LM2902KNSR for the identical part in tape-and-reel for automated production lines - no redesign required. Choose LM2902D if ESD enhancement is not needed and lowest cost dominates. Choose LM2902KV for the enhanced K-family parameters in demanding environments. Choose LM324D when your rail exceeds 26 V up to 32 V. In all cases the 14-SOIC footprint is shared, so PCB reuse across variants is straightforward; always confirm the operating temperature range and ESD requirement against your system environment before finalizing the BOM.

Comparación con alternativas

Parámetro Este producto LM2902KNSR LM2902D LM324D
Package 14-SOIC (NS, 5.30 mm) 14-SOIC (NS) - same 14-SOIC - same footprint 14-SOIC - same footprint
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Number of Circuits 4 4 4 4
Gain Bandwidth Product 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz
Slew Rate 0.5 V/us 0.5 V/us 0.5 V/us 0.5 V/us
Maximum Supply Voltage 26 V (single) 26 V (single) 26 V (single) 32 V (single)
Supply Current (Typ) 0.8 mA 0.8 mA 0.8 mA 1.2 mA (typical family figure)
ESD Rating 2 kV (improved) 2 kV (improved) standard LM2902 rating standard LM324 rating

Diferenciadores clave

  • Improved 2 kV ESD robustness (frente a LM2902D)
  • 100% identical drop-in in reel format (frente a LM2902KNSR)
  • Higher voltage rating within the same footprint (frente a LM2902KNSR / LM324D)

Notas de diseño

Decouple the shared VCC pin (pin 4) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus a 1-10 uF bulk capacitor per board region. Because all four amplifier channels share this supply node, supply-borne crosstalk between channels is the most common defect in LM2902 layouts - a mixer channel bleeding into a filter channel traces back to shared supply impedance. In single-supply 24 V systems, verify the 26 V absolute maximum leaves margin for supply transients or add a series regulator or Zener clamp.

Do not rely on the outputs to reach the positive rail. The LM2902KNSG4 output stage cannot swing to VCC; reserve roughly 1.5 V of headroom when setting gain stages. Also avoid using the device as a precision comparator with wired-OR outputs - outputs are push-pull, not open-collector. When interfacing to 5 V or 3.3 V logic from a 24 V rail, add resistive dividers or clamps. Finally, inputs can be damaged if taken more than the datasheet differential limit below VEE when the device is unpowered; check the absolute maximum table in the TI LM2902K datasheet for the exact figure.

Connect the VEE/GND pin (pin 11) directly to a clean analog ground with a short, wide trace; this pin is the return for all four input stages. Keep feedback resistors close to the inverting input pins to minimize stray capacitance that can cause ringing at higher closed-loop gains. For audio or precision channels, group each amplifier's components locally rather than clustering all four channels' inputs together, and route ground under the feedback network as a mini-ground pour to reduce channel-to-channel crosstalk.

Información de cumplimiento

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The G4 suffix denotes TI's RoHS-compliant green package version. REACH, lead-free and halogen-free status should be confirmed against TI environmental documentation.

Datos verificados el: 2026-11-08 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

LM2902KNSG4 datasheet LM2902KNSG4 pinout LM2902KNSG4 equivalent LM2902KNSG4 replacement LM2902KNSG4 vs LM324D LM2902KNSG4 price Texas Instruments LM2902KNSG4 LM2902KNSG4 stock LM2902 quad op-amp 14-SOIC pinout LM2902 vs LM324 difference quad op-amp 1.2MHz 26V SOIC-14 LM2902 application circuit

Componentes & términos relacionados

Texas Instruments LM2902KNSG4 LM2902K LM2902KNSR LM2902KV LM324D operational amplifier op-amp quad op-amp general-purpose amplifier linear IC gain-bandwidth product slew rate 14-SOIC SOIC package family surface mount RoHS ESD robustness industrial signal conditioning automotive electronics single-supply operation -40C to +125C temperature range
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ