LM2902YPT - Low-Power Quad Op Amp, 1.3 MHz | STMicroelectronics
料号: LM2902YPT ✓ 量产中LM2902YPT 概述
An operational amplifier is an analog signal-processing building block that compares its inverting and non-inverting inputs and drives its output toward the higher input potential. Within the broader hierarchy, a quad operational amplifier contains four amplifiers in one package, reducing board area and simplifying multi-channel instrumentation, sensor, and feedback-control designs. The LM2902 family combines internal frequency compensation with low power consumption, making it suitable for general-purpose signal conditioning rather than precision or high-speed applications.
Key characteristics include push-pull output capability, low input bias current, and input common-mode operation that allows the inputs to approach the supply rails. The four amplifiers share supply pins but remain electrically independent, allowing simultaneous use for sensing, amplification, filtering, and actuator drive. Because all four channels operate from the same package and supply network, common power-supply bypassing and thermal management serve all channels at once.
The internally compensated architecture makes the LM2902 stable in the voltage-follower configuration without external compensation networks. Its 1.3 MHz bandwidth is adequate for audio-frequency, industrial-control, and general feedback loops, while the 0.4 V/µs slew rate limits large-signal response. Applications include transducer interfaces, low-level sensor amplification, motor-feedback networks, audio preamplification, and multi-channel control systems.
Designers should keep input and output pins within the common-mode and output-swing limits shown in the manufacturer datasheet. Place the supply bypass capacitor close to the device, maintain short feedback paths, and avoid driving capacitive loads without isolation. The quad package reduces component count, but all four channels share the package thermal path.
This page combines manufacturer specifications, application guidance, package details, and drop-in replacement analysis to support faster component selection and PCB design for automotive and industrial control systems.
直接替换替代料: LM2902YPT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2902YPT (相同外形与封装尺寸) ——差异在于 Package, Amplifier Type, Output Type, RoHS Status.
LM2902YDT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2902YHT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2902PT
✅ 直接替换📋 参考替代料(不在目录中)
LM2902BIDR
✅ 直接替换📋 参考替代料(不在目录中)
LM2902YPT 最大额定值与电气特性
| Number of Amplifiers | 4 circuits |
| Amplifier Type | Low-power general-purpose operational amplifier |
| Internal Frequency Compensation | Yes |
| Input Bias Current | 20 nA |
| Gain-Bandwidth Product | 1.3 MHz |
| Slew Rate | 0.4 V/µs |
| Typical Input Offset Voltage | 7 mV |
| 输出类型 | Push-pull |
| Supply Voltage Range | 3 V to 36 V |
| 工作温度范围 | -40 °C to +125 °C |
| Package Type | 14-pin TSSOP |
| 安装类型 | Surface mount |
| 引脚数 | 14 pins |
| Automotive and Industrial Design | Yes |
| RoHS 状态 | Compliant |
LM2902YPT 引脚配置
| 引脚 1 | OUT 1 — Amplifier 1 output |
| 引脚 2 | IN- 1 — Amplifier 1 inverting input |
| 引脚 3 | IN+ 1 — Amplifier 1 non-inverting input |
| 引脚 4 | V+ — Positive supply voltage |
| 引脚 5 | IN+ 2 — Amplifier 2 non-inverting input |
| 引脚 6 | IN- 2 — Amplifier 2 inverting input |
| 引脚 7 | OUT 2 — Amplifier 2 output |
| 引脚 8 | OUT 3 — Amplifier 3 output |
| 引脚 9 | IN- 3 — Amplifier 3 inverting input |
| 引脚 10 | IN+ 3 — Amplifier 3 non-inverting input |
| 引脚 11 | V- — Negative supply voltage |
| 引脚 12 | IN+ 4 — Amplifier 4 non-inverting input |
| 引脚 13 | IN- 4 — Amplifier 4 inverting input |
| 引脚 14 | OUT 4 — Amplifier 4 output |
典型应用
LM2902YPT 适用于 6 应用s: Automotive Sensor Signal Conditioning, Industrial Control Loop Amplification, Low-Level Transducer Interface, Audio Preamplifier and Mixer, Motor Feedback and Drive Interface, Battery-Powered Instrumentation.
Automotive Sensor Signal Conditioning
The LM2902YPT suits automotive sensor interfaces where four channels must amplify low-level signals in a high-voltage environment. Its 3 V to 36 V supply range tolerates a 12 V or 24 V automotive rail, while the 20 nA input bias current limits the error introduced by high-impedance sensors. Each internally compensated amplifier can form a stable voltage follower or closed-loop gain stage without external compensation components. The four channels share the TSSOP-14 package, reducing board area for pressure, position, and temperature sensing. Design the input network for the automotive transients and common-mode range specified in the manufacturer datasheet.
推荐
Industrial Control Loop Amplification
The LM2902YPT is useful in industrial controllers that need several feedback and error-amplifier channels. A 1.3 MHz gain-bandwidth product supports moderate-bandwidth control loops, while the 0.4 V/µs slew rate provides adequate response for slow process signals and actuator feedback. The four amplifiers share a single supply arrangement and can implement difference amplifiers, comparators with hysteresis, and current-feedback stages. Use short feedback routes and place supply decoupling close to the package to prevent switching equipment from injecting noise into the control signals.
推荐
Low-Level Transducer Interface
The LM2902YPT fits low-level transducer front ends where the source impedance makes input bias current important. Its 20 nA input bias current helps preserve weak sensor signals, and the typical 7 mV input offset voltage establishes the baseline error that the system must tolerate. Four channels allow simultaneous measurement of bridge, temperature, or strain-gauge inputs without requiring four separate packages. Place high-value input resistors near the amplifier pins and guard sensitive nodes to minimize leakage and surface contamination before applying the specified gain.
推荐
Audio Preamplifier and Mixer
The LM2902YPT can provide gain for low-level audio channels in industrial monitoring equipment and communication products. Its 1.3 MHz bandwidth covers much of the audio band, and the 0.4 V/µs slew rate avoids excessive distortion for routine microphone or line-level signals. The four-channel arrangement supports two stereo preamplifier paths or a mixer with buffering. Conventional push-pull outputs are appropriate when signals remain within the specified output swing, but a rail-to-rail amplifier is preferable for very low supply voltages or near-rail output requirements.
推荐
Motor Feedback and Drive Interface
The LM2902YPT is applicable to motor-control systems that monitor current or position feedback and generate analog control voltages. Four channels can provide sensing, gain, offset correction, and output drive functions around a power converter. The 3 V to 36 V operating supply range suits 24 V industrial motor systems, while low input bias current is helpful when the feedback divider has high impedance. Keep the amplifier away from high-current switching traces and use the application guidance in the LM2902 datasheet to establish safe input and output operating conditions.
推荐
Battery-Powered Instrumentation
The LM2902YPT supports low-power instrumentation when a 1.3 MHz bandwidth amplifier is sufficient. The four-channel configuration allows multiplexed sensing, buffering, and gain stages to share one package instead of using separate amplifiers. Low input bias current reduces loading on high-impedance sensors, and the broad 3 V to 36 V supply range accommodates both low-voltage portable systems and higher industrial rails. Confirm quiescent current against the current budget in the manufacturer datasheet and disable unused channels where the circuit architecture permits.
推荐
推荐产品汇总
工程参考数据: LM2902YPT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2902YDT | LM2902YHT | LM2902PT | LM2902BIDR |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | ROHM Semiconductor | Texas Instruments |
| Package | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 |
| Supply Voltage Range | 3 V to 36 V | 3 V to 36 V | 3 V to 36 V | 3 V to 36 V | Up to 36 V |
| Output Architecture | Push-pull | Push-pull | Push-pull | Push-pull | Push-pull |
| Frequency Compensation | Internal | Internal | Internal | Internal | Internal |
关键差异点
- Low-power quad integration in a compact TSSOP package (对比 LM324ADR)
- Low input bias current for impedance-sensitive signals (对比 LM324ADR)
- Wide supply-voltage range (对比 TS952IPT)
- Internally compensated amplifiers simplify feedback design (对比 LM2904PT)
设计说明
Place the supply bypass capacitor immediately adjacent to the LM2902YPT V+ and V- pins, using the shortest and widest practical connection. Because all four amplifiers share the package supply pins, this placement reduces the series inductance seen by every channel. Route sensitive inverting-input and feedback nets away from the V+ return path and from high-current switching nodes.
Do not assume the LM2902's conventional push-pull output can swing fully to either supply rail. Check input common-mode range and output-swing limits in the STMicroelectronics datasheet for the actual supply voltage. A rail-to-rail quad amplifier is preferable when the signal must approach a rail, and an isolation resistor may be needed when driving a capacitive load.
Keep each amplifier's feedback components close to its inverting input and avoid sharing long feedback traces between channels. Use the four channels for independent functions when possible to reduce common-impedance coupling. If one channel drives an ADC or sensor while another handles fast switching-control logic, separate their return-current paths and place the analog amplifier closer to the sensitive source.
The 14-pin TSSOP shares one thermal path across all four amplifiers. Although a low-power quad op amp generally dissipates little energy, continuous high-load operation across several channels can raise the package temperature. Spread heat-generating feedback networks across the board and provide adequate copper around the package, especially when the amplifier is mounted near a power converter.
合规信息
RoHS compliance is identified on the LCSC product listing for this exact MPN. REACH, halogen-free, conflict-minerals, and automotive-qualification status are not established by the available product information.