STMicroelectronics

LM2902YPT - Low-Power Quad Op Amp, 1.3 MHz | STMicroelectronics

MPN: LM2902YPT ✓ 啟用中
7 mV Vdss 20 nA Id 14-pin TSSOP Package Yes Speed
MOQ: 1 |

LM2902YPT 概覽

The STMicroelectronics LM2902YPT is a low-power, general-purpose quad operational amplifier containing four independent, internally frequency-compensated amplifiers in a 14-pin TSSOP package. Each amplifier features a 1.3 MHz gain-bandwidth product, 0.4 V/µs slew rate, low 20 nA input bias current, and a typical input offset voltage of 7 mV. The device is designed for automotive and industrial control systems operating from a single supply or split supplies.

An operational amplifier is an analog signal-processing building block that compares its inverting and non-inverting inputs and drives its output toward the higher input potential. Within the broader hierarchy, a quad operational amplifier contains four amplifiers in one package, reducing board area and simplifying multi-channel instrumentation, sensor, and feedback-control designs. The LM2902 family combines internal frequency compensation with low power consumption, making it suitable for general-purpose signal conditioning rather than precision or high-speed applications.

Key characteristics include push-pull output capability, low input bias current, and input common-mode operation that allows the inputs to approach the supply rails. The four amplifiers share supply pins but remain electrically independent, allowing simultaneous use for sensing, amplification, filtering, and actuator drive. Because all four channels operate from the same package and supply network, common power-supply bypassing and thermal management serve all channels at once.

The internally compensated architecture makes the LM2902 stable in the voltage-follower configuration without external compensation networks. Its 1.3 MHz bandwidth is adequate for audio-frequency, industrial-control, and general feedback loops, while the 0.4 V/µs slew rate limits large-signal response. Applications include transducer interfaces, low-level sensor amplification, motor-feedback networks, audio preamplification, and multi-channel control systems.

Designers should keep input and output pins within the common-mode and output-swing limits shown in the manufacturer datasheet. Place the supply bypass capacitor close to the device, maintain short feedback paths, and avoid driving capacitive loads without isolation. The quad package reduces component count, but all four channels share the package thermal path.

This page combines manufacturer specifications, application guidance, package details, and drop-in replacement analysis to support faster component selection and PCB design for automotive and industrial control systems.

直接替換替代品,適用於 LM2902YPT — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: LM2902YPT (相同外形與佔位) — 差異在於 Package, Amplifier Type, Output Type, RoHS Status.

Texas Instruments
Package: 14-TSSOP (PW)
Amplifier Type: General Purpose
RoHS Status: Compliant (E4 suffix denotes lead-free)
比較對象 LM2902YPT →
STMicroelectronics
Package: 14-TSSOP
比較對象 LM2902YPT →
Texas Instruments
Package: 8-TSSOP (PW)
Output Type: Open collector
比較對象 LM2902YPT →

LM2902YDT

✅ 直接替換 ⚠️ 規格未經驗證
📦 14-pin TSSOP
Same LM2902 four-amplifier architecture and 1.3 MHz bandwidth; ordering-code temperature and ordering details differ by up to 10%

📋 參考替代品(不在目錄中)

LM2902YHT

✅ 直接替換 ⚠️ 規格未經驗證
📦 14-pin TSSOP
Same LM2902 family, TSSOP-14 land pattern, 1.3 MHz bandwidth and 20 nA bias current; variant-specific temperature grade differs by up to 10%

📋 參考替代品(不在目錄中)

LM2902PT

✅ 直接替換
📦 14-pin TSSOP
Cross-brand quad LM2902-type amplifier with nominal 1.2 MHz bandwidth versus 1.3 MHz, a 7.7% bandwidth reduction

📋 參考替代品(不在目錄中)

LM2902BIDR

✅ 直接替換
📦 14-pin TSSOP
Next-generation quad 36 V bipolar amplifier with comparable architecture; bias current and offset ratings differ by up to 20%

📋 參考替代品(不在目錄中)

LM2902YPT 最大額定值與電氣特性

Number of Amplifiers 4 circuits
Amplifier Type Low-power general-purpose operational amplifier
Internal Frequency Compensation Yes
Input Bias Current 20 nA
Gain-Bandwidth Product 1.3 MHz
Slew Rate 0.4 V/µs
Typical Input Offset Voltage 7 mV
輸出類型 Push-pull
Supply Voltage Range 3 V to 36 V
工作溫度範圍 -40 °C to +125 °C
Package Type 14-pin TSSOP
安裝類型 Surface mount
腳位數 14 pins
Automotive and Industrial Design Yes
RoHS 狀態 Compliant

LM2902YPT 腳位配置

TSSOP-14 (4.4mm) Package Pinout Diagram TSSOP-14 4.4x5mm, P0.65mm, JEDEC MO-153. 14-pin thin shrink. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 TSSOP-14 (4.4mm)
腳位 1 OUT 1 — Amplifier 1 output
腳位 2 IN- 1 — Amplifier 1 inverting input
腳位 3 IN+ 1 — Amplifier 1 non-inverting input
腳位 4 V+ — Positive supply voltage
腳位 5 IN+ 2 — Amplifier 2 non-inverting input
腳位 6 IN- 2 — Amplifier 2 inverting input
腳位 7 OUT 2 — Amplifier 2 output
腳位 8 OUT 3 — Amplifier 3 output
腳位 9 IN- 3 — Amplifier 3 inverting input
腳位 10 IN+ 3 — Amplifier 3 non-inverting input
腳位 11 V- — Negative supply voltage
腳位 12 IN+ 4 — Amplifier 4 non-inverting input
腳位 13 IN- 4 — Amplifier 4 inverting input
腳位 14 OUT 4 — Amplifier 4 output

典型應用

LM2902YPT 適用於 6 應用s: Automotive Sensor Signal Conditioning, Industrial Control Loop Amplification, Low-Level Transducer Interface, Audio Preamplifier and Mixer, Motor Feedback and Drive Interface, Battery-Powered Instrumentation.

🚗

Automotive Sensor Signal Conditioning

The LM2902YPT suits automotive sensor interfaces where four channels must amplify low-level signals in a high-voltage environment. Its 3 V to 36 V supply range tolerates a 12 V or 24 V automotive rail, while the 20 nA input bias current limits the error introduced by high-impedance sensors. Each internally compensated amplifier can form a stable voltage follower or closed-loop gain stage without external compensation components. The four channels share the TSSOP-14 package, reducing board area for pressure, position, and temperature sensing. Design the input network for the automotive transients and common-mode range specified in the manufacturer datasheet.

🏭

Industrial Control Loop Amplification

The LM2902YPT is useful in industrial controllers that need several feedback and error-amplifier channels. A 1.3 MHz gain-bandwidth product supports moderate-bandwidth control loops, while the 0.4 V/µs slew rate provides adequate response for slow process signals and actuator feedback. The four amplifiers share a single supply arrangement and can implement difference amplifiers, comparators with hysteresis, and current-feedback stages. Use short feedback routes and place supply decoupling close to the package to prevent switching equipment from injecting noise into the control signals.

🔧

Low-Level Transducer Interface

The LM2902YPT fits low-level transducer front ends where the source impedance makes input bias current important. Its 20 nA input bias current helps preserve weak sensor signals, and the typical 7 mV input offset voltage establishes the baseline error that the system must tolerate. Four channels allow simultaneous measurement of bridge, temperature, or strain-gauge inputs without requiring four separate packages. Place high-value input resistors near the amplifier pins and guard sensitive nodes to minimize leakage and surface contamination before applying the specified gain.

🎧

Audio Preamplifier and Mixer

The LM2902YPT can provide gain for low-level audio channels in industrial monitoring equipment and communication products. Its 1.3 MHz bandwidth covers much of the audio band, and the 0.4 V/µs slew rate avoids excessive distortion for routine microphone or line-level signals. The four-channel arrangement supports two stereo preamplifier paths or a mixer with buffering. Conventional push-pull outputs are appropriate when signals remain within the specified output swing, but a rail-to-rail amplifier is preferable for very low supply voltages or near-rail output requirements.

⚡

Motor Feedback and Drive Interface

The LM2902YPT is applicable to motor-control systems that monitor current or position feedback and generate analog control voltages. Four channels can provide sensing, gain, offset correction, and output drive functions around a power converter. The 3 V to 36 V operating supply range suits 24 V industrial motor systems, while low input bias current is helpful when the feedback divider has high impedance. Keep the amplifier away from high-current switching traces and use the application guidance in the LM2902 datasheet to establish safe input and output operating conditions.

🖥️

Battery-Powered Instrumentation

The LM2902YPT supports low-power instrumentation when a 1.3 MHz bandwidth amplifier is sufficient. The four-channel configuration allows multiplexed sensing, buffering, and gain stages to share one package instead of using separate amplifiers. Low input bias current reduces loading on high-impedance sensors, and the broad 3 V to 36 V supply range accommodates both low-voltage portable systems and higher industrial rails. Confirm quiescent current against the current budget in the manufacturer datasheet and disable unused channels where the circuit architecture permits.

What is the LM2902YPT?
The LM2902YPT is a STMicroelectronics low-power quad operational amplifier with four independent, internally frequency-compensated amplifiers in a 14-pin TSSOP package. According to the STMicroelectronics LM2902 datasheet, the device is intended for automotive and industrial control systems and provides a 1.3 MHz gain-bandwidth product, 0.4 V/µs slew rate, and 20 nA input bias current.
What are the key specifications of LM2902YPT that engineers should know?
The LM2902YPT combines four low-power operational amplifiers, a 1.3 MHz gain-bandwidth product, 0.4 V/µs slew rate, 20 nA input bias current, and a typical 7 mV input offset voltage. The STMicroelectronics LM2902 datasheet identifies a 3 V to 36 V supply range and a 14-pin TSSOP package. These characteristics suit general-purpose industrial and automotive signal-conditioning circuits.
Can LM2902YPT operate from a single supply?
Yes. The LM2902YPT operates from a single positive supply or from split positive and negative supplies. The STMicroelectronics LM2902 datasheet specifies a 3 V to 36 V operating supply range, allowing the device to be used in single-rail sensor systems or bipolar-style control circuits. Input common-mode and output-swing limits must still be respected.
Does the LM2902YPT need external frequency compensation?
No. Each amplifier in the LM2902YPT is internally frequency compensated, so no external compensation network is required for unity-gain voltage-follower use. According to the STMicroelectronics LM2902 datasheet, the circuit contains four independent, high-gain, internally compensated operational amplifiers. Compensation values should still be checked for unusual noise-gain configurations.
Where can I download the LM2902YPT datasheet PDF?
The official STMicroelectronics LM2902 datasheet PDF is available at https://www.st.com/resource/en/datasheet/lm2902.pdf. It contains the electrical characteristics, pin configuration, typical application circuits, and operating limits for the LM2902 family. Use the manufacturer document for design sign-off and refer to the TSSOP-14 pin description before assigning PCB tracks.
Where is the LM2902YPT pinout located?
The LM2902YPT pin description is included in the STMicroelectronics LM2902 manufacturer datasheet. The 14-pin TSSOP outline numbers four channels as 1 OUT, 2 inverting input, 3 non-inverting input, and 4 V+ for amplifier 1, with the other amplifiers distributed across pins 5 through 14. Assign PCB tracks using that pin-description table rather than a generic quad-op-amp drawing.
What can replace an LM2902YPT?
A suitable replacement must use the same 14-pin TSSOP land pattern and provide four amplifiers with compatible supply-voltage and input/output characteristics. The STMicroelectronics LM2902 family includes related quad amplifiers that share the footprint, while some other LM2902 variants use SOIC or DIP packages and therefore are not direct PCB drop-ins. Request a quote for availability of qualified alternatives.
Is LM2902YPT the same as LM2904PT?
No. The LM2904 is a rail-to-rail output amplifier, whereas the LM2902 uses conventional push-pull output stages and is characterized as a low-power bipolar amplifier. Their input characteristics, output-swing behavior, and design intent differ, so substituting one for the other requires reviewing the signal swing, supply voltage, noise gain, and stability requirements rather than assuming identical performance.
When should I choose LM2902YPT instead of a rail-to-rail quad op amp?
Choose the LM2902YPT when low power consumption, a 1.3 MHz bandwidth, and conventional push-pull output operation are the priorities. Its 20 nA input bias current is useful with higher-impedance sensors, while 0.4 V/µs slew rate supports moderate-frequency signals. Select a rail-to-rail amplifier instead when the signal must swing close to either supply rail.
Is LM2902YPT suitable for automotive applications?
Yes. The STMicroelectronics LM2902 datasheet specifically describes the circuit as designed for automotive and industrial control systems. Its 3 V to 36 V supply range, low 20 nA input bias current, and -40 °C to +125 °C operating range fit many 12 V or 24 V vehicle systems. Confirm the specific qualification requirements for the finished ECU or vehicle platform.
What is the best STMicroelectronics equivalent for LM2902YPT?
The closest same-family choice is another STMicroelectronics LM2902 variant specified in the same 14-pin TSSOP footprint. The LM2902 family shares the basic four-amplifier architecture, 1.3 MHz-class bandwidth, and push-pull output behavior, making the closest variant preferable to unrelated precision amplifiers. Confirm temperature grade, supply limits, and ordering code before substitution.
How should decoupling capacitors be placed around LM2902YPT?
Place the supply bypass capacitor as close as practical to the device's V+ and V- pins, and route the connection with a short, low-inductance path. The LM2902YPT contains four amplifiers sharing the same package supply pins, so one well-placed bypass capacitor benefits all channels. Keep sensitive input and feedback traces away from the supply-return path to reduce coupling.
What is the lead time for LM2902YPT?
Current lead time and available quantity should be confirmed through the Request a Quote form on this page. The LM2902YPT is an active STMicroelectronics general-purpose quad op amp, and production schedules can vary with automotive and industrial demand. Provide your required quantity, date code, and target ship-to location when requesting the quotation.
Is LM2902YPT in stock?
Stock status changes with purchasing volume and manufacturing cycles, so request a current quotation through the Request a Quote form on this page. The device is identified as an active STMicroelectronics LM2902 family member in a 14-pin TSSOP package. Including your required quantity and acceptable lead time allows the sourcing team to confirm the latest allocation.
Where to buy LM2902YPT online?
Use the Request a Quote form on this page to request LM2902YPT pricing, stock confirmation, and current lead time. The part is a STMicroelectronics 14-pin TSSOP quad operational amplifier rated for automotive and industrial control systems. Specify reel quantity, date-code preference, and shipment destination so the quotation can be matched to your production requirements.
How do I compare LM2902YPT and LM2902PT?
Compare package drawing, temperature grade, and the orderable suffix rather than assuming that both order codes share the same footprint. The LM2902YPT is specified in a 14-pin TSSOP package, while LM2902PT package information depends on the manufacturer and exact ordering code. Verify the mechanical drawing and pin numbering before treating either part as a drop-in replacement.

工程參考資料,適用於 LM2902YPT — 比較、設計指引及合規資訊。

選型指南

Choose the LM2902YPT for four-channel, low-power analog signal conditioning on 3 V to 36 V rails, particularly in automotive and industrial control systems where 20 nA input bias current, internal compensation, and conventional push-pull outputs are suitable. Choose LM2902YDT or LM2902YHT when an equivalent STMicroelectronics ordering code is preferred, after confirming temperature grade and orderable suffix. Consider LM2902PT from ROHM Semiconductor for a cross-brand quad implementation with approximately 1.2 MHz bandwidth, a 7.7% reduction from the STMicroelectronics part. Consider LM2902BIDR from Texas Instruments when a next-generation 36 V bipolar family is acceptable. Do not select a rail-to-rail quad amplifier unless near-rail output swing is required, because its output behavior differs from the LM2902. In every case, verify the mechanical drawing, pin numbering, temperature grade, and electrical limits before treating the alternative as a drop-in replacement.

與替代品比較

參數 本產品 LM2902YDT LM2902YHT LM2902PT LM2902BIDR
Brand STMicroelectronics STMicroelectronics STMicroelectronics ROHM Semiconductor Texas Instruments
Package 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP
Number of Amplifiers 4 4 4 4 4
Supply Voltage Range 3 V to 36 V 3 V to 36 V 3 V to 36 V 3 V to 36 V Up to 36 V
Output Architecture Push-pull Push-pull Push-pull Push-pull Push-pull
Frequency Compensation Internal Internal Internal Internal Internal

主要差異化特點

  • Low-power quad integration in a compact TSSOP package (對比LM324ADR)
  • Low input bias current for impedance-sensitive signals (對比LM324ADR)
  • Wide supply-voltage range (對比TS952IPT)
  • Internally compensated amplifiers simplify feedback design (對比LM2904PT)

設計說明

Place the supply bypass capacitor immediately adjacent to the LM2902YPT V+ and V- pins, using the shortest and widest practical connection. Because all four amplifiers share the package supply pins, this placement reduces the series inductance seen by every channel. Route sensitive inverting-input and feedback nets away from the V+ return path and from high-current switching nodes.

Do not assume the LM2902's conventional push-pull output can swing fully to either supply rail. Check input common-mode range and output-swing limits in the STMicroelectronics datasheet for the actual supply voltage. A rail-to-rail quad amplifier is preferable when the signal must approach a rail, and an isolation resistor may be needed when driving a capacitive load.

Keep each amplifier's feedback components close to its inverting input and avoid sharing long feedback traces between channels. Use the four channels for independent functions when possible to reduce common-impedance coupling. If one channel drives an ADC or sensor while another handles fast switching-control logic, separate their return-current paths and place the analog amplifier closer to the sensitive source.

The 14-pin TSSOP shares one thermal path across all four amplifiers. Although a low-power quad op amp generally dissipates little energy, continuous high-load operation across several channels can raise the package temperature. Spread heat-generating feedback networks across the board and provide adequate copper around the package, especially when the amplifier is mounted near a power converter.

合規資訊

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

RoHS compliance is identified on the LCSC product listing for this exact MPN. REACH, halogen-free, conflict-minerals, and automotive-qualification status are not established by the available product information.

資料驗證日期: 2026-11-13 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

LM2902YPT datasheet LM2902YPT datasheet pdf LM2902YPT pinout LM2902YPT schematic LM2902YPT equivalent LM2902YPT replacement LM2902YPT cross reference LM2902YPT price LM2902YPT stock STMicroelectronics LM2902YPT LM2902YPT TSSOP-14 LM2902YPT vs LM2902PT LM2902YPT 1.3 MHz op amp LM2902YPT automotive sensor amplifier

相關元件與詞彙

STMicroelectronics LM2902YPT LM2902 quad operational amplifier low-power operational amplifier bipolar operational amplifier signal conditioning feedback control gain-bandwidth product slew rate input bias current input offset voltage push-pull output internal frequency compensation TSSOP-14 surface mount automotive control systems industrial control systems RoHS single-supply operation
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情