LM2903AM8-13 - Dual Comparator, A-Grade 1mV | Diodes Inc
料号: LM2903AM8-13 ✓ 量产中LM2903AM8-13 概述
A voltage comparator is an analog IC that compares two input voltages and drives its output to indicate which input is higher. Comparators form the bridge between the analog front end and digital logic: they are classified within the linear IC family, sitting alongside amplifiers and voltage references in the signal-chain hierarchy, and are foundational building blocks of power management, sensing, and monitoring subsystems.
Key features include a common-mode input voltage range that includes ground, enabling single-supply operation from ground-referenced sensors; a differential input voltage range equal to the power supply voltage, which protects the device during fault conditions; and a low output saturation voltage of 200 mV at 4 mA sink current. The output is compatible with TTL, MOS, and CMOS logic levels across a wide supply range.
The open-collector output architecture allows wired-OR configurations and interfacing to logic rails above or below the comparator supply, provided the absolute maximum output voltage is respected. Input PNP transistors permit input voltages down to the negative rail, making ground-sense comparators, zero-crossing detectors, and current-sense threshold circuits straightforward on a single supply.
Typical applications include over-voltage and under-voltage monitoring in industrial systems, battery-powered limit detection, oscillator and relaxation-clock circuits, window comparators in power supplies, and automotive sensor thresholding where the wide temperature grade matters.
Design consideration: because the output is open-collector, always provide a pull-up resistor to the desired logic rail; the pull-up value sets sink current and switching speed. Small hysteresis (positive feedback of a few millivolts) is recommended in noisy environments to prevent output chatter near the threshold.
This page adds value beyond the manufacturer datasheet by compiling verified drop-in alternatives, an 8-pin MSOP pinout map, parameter comparison tables, and practical engineering design notes in one place for faster sourcing and layout decisions.
直接替换替代料: LM2903AM8-13 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2903AM8-13 (相同外形与封装尺寸) ——差异在于 Logic Compatibility, Output Type, Number of Channels, Package, Common-Mode Input Range.
LM2903M8-13
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM2903AQM8-13
✅ 直接替换联系询价
查看数据手册 →LM2903AM8-13 最大额定值与电气特性
| 功能 | Dual differential voltage comparator |
| Number of Channels | 2 |
| Input Offset Voltage (A device) | 1 mV |
| 输出类型 | Open-collector, rail-to-rail |
| Output Saturation Voltage | 200 mV at 4 mA |
| Common-Mode Input Range | Includes ground (V-) |
| Differential Input Voltage Range | Equal to supply voltage |
| Logic Compatibility | TTL, MOS, CMOS |
| 封装 | MSOP-8 |
| 安装类型 | Surface Mount |
| RoHS 状态 | Fully RoHS compliant, totally lead-free |
| Halogen / Antimony | Halogen and antimony free (Green) |
LM2903AM8-13 引脚配置
| 引脚 1 | OUT1 — Comparator 1 open-collector output |
| 引脚 2 | IN1- — Comparator 1 inverting input |
| 引脚 3 | IN1+ — Comparator 1 non-inverting input |
| 引脚 4 | GND — Ground / negative supply (V-) |
| 引脚 5 | IN2+ — Comparator 2 non-inverting input |
| 引脚 6 | IN2- — Comparator 2 inverting input |
| 引脚 7 | OUT2 — Comparator 2 open-collector output |
| 引脚 8 | V+ — Positive supply |
典型应用
LM2903AM8-13 适用于 6 应用s: Over-Voltage / Under-Voltage Monitoring, Battery-Powered Limit Detection, Industrial Sensor Thresholding, Oscillator and Clock Generation, Switch-Mode Power Supply Fault Flags, Automotive Sensor Thresholding.
Over-Voltage / Under-Voltage Monitoring
The LM2903AM8-13 fits supply-rail supervision because its common-mode input range includes ground and its differential input range equals the full supply voltage, so the inputs survive fault transients without clamps. Each of the two comparators in the 8-MSOP package can watch a separate rail: one detects under-voltage and the other over-voltage, with the open-collector outputs wired-OR into a single fault flag. The A-grade 1 mV offset keeps the trip point within 1 mV of the resistor-divider setting, and adding a few millivolts of hysteresis through positive feedback prevents chatter near the threshold. A 10 kOhm pull-up to the monitoring logic rail gives a clean TTL/CMOS-compatible fault signal at roughly 0.5 mA sink current, well within the 200 mV saturation rating at 4 mA.
推荐
Battery-Powered Limit Detection
In battery-operated devices the LM2903AM8-13 serves as a low-battery or charge-complete detector. Inputs referenced to ground on a single positive supply simplify sensing across the cell stack, and the open-collector output only draws current when sinking, conserving energy in duty-cycled systems. The A-grade 1 mV offset means the detected threshold tracks the divider accurately across temperature, important because battery discharge curves have shallow slopes near the cutoff region. Place a resistor divider on IN+ from the battery node and a reference (such as a TL431 shunt regulator) on IN-, then pull the output up to the MCU supply so the same signal works across 3.3 V and 5 V controllers without level shifting. Two thresholds (warning and shutdown) fit in one package.
推荐
Industrial Sensor Thresholding
Industrial automation panels use the LM2903AM8-13 to convert analog sensor outputs (photodiodes, thermistor bridges, pressure dividers) into binary status flags. The ground-including common-mode range allows ground-referenced sensors to drive the inputs directly on a 24 V-derived single supply (within ratings), and the differential range equal to the supply voltage tolerates miswiring faults. The 1 mV A-grade offset is valuable when sensor span is small: a 10 mV full-scale bridge signal retains meaningful resolution. Add RC filtering plus 5-20 mV hysteresis to reject relay and motor noise common in factory environments. The MSOP-8 footprint saves board area in dense I/O modules, and the output pulls up to a PLC-compatible logic rail through a single resistor.
推荐
Oscillator and Clock Generation
Comparators make robust relaxation oscillators, and the LM2903AM8-13 implements a classic RC astable with one comparator per oscillator: an RC network on the input and positive feedback for hysteresis on the other. The rail-to-rail open-collector output swinging between 200 mV saturation and the pull-up rail gives a well-defined logic-level clock for gating counters or driving optocoupler LEDs through a series resistor. Frequency is set by R and C alone; the A-grade 1 mV offset contributes minimally to duty-cycle error compared to a 2 mV standard-grade part, which matters when generating symmetrical clocks. Ground-including common-mode operation simplifies the timing network on a single supply, and the MSOP-8 package hosts two independent oscillators on one footprint.
推荐
Switch-Mode Power Supply Fault Flags
In AC-DC and DC-DC converters, the LM2903AM8-13 provides secondary-side protection flags: over-current detection across a sense resistor, over-voltage crowbar triggering, and under-voltage lockout of downstream loads. Its differential input range equal to the supply voltage lets one input sit at the switch-node sense voltage while the other references a divider, surviving startup transients without input clamps. The open-collector output can directly drive an optocoupler LED toward the primary controller, isolating the fault signal across the safety barrier. The 200 mV saturation at 4 mA suits the low side of an opto LED string, and the 1 mV offset keeps an over-current trip set at, say, 50 mV accurate to about 2%. Two comparators handle OCP and OVP independently in one MSOP-8 package.
推荐
Automotive Sensor Thresholding
For vehicle subsystems (non-Q-grade builds and prototyping of Q-grade designs), the LM2903AM8-13 detects analog thresholds from coolant-level floats, door-switch dividers, and lamp-status sense lines. The ground-referenced input range matches automotive chassis-referenced sensors on a single 12 V-derived supply, and the differential input range equal to the supply absorbs load-dump adjacent transients when combined with proper series resistance. Wire the open-collector outputs into wired-OR fault buses feeding the body controller. When the program reaches production and AEC-grade qualification is mandated, switch to the pin-identical LM2903AQM8-13 in the same 8-MSOP footprint - no layout change is required, preserving the validation effort already invested in the prototype board.
推荐
推荐产品汇总
工程参考数据: LM2903AM8-13 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2903M8-13 | LM2903AQM8-13 |
|---|---|---|---|
| Package | MSOP-8 | MSOP-8 - same | MSOP-8 - same |
| Brand | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated |
| Number of Channels | 2 | 2 | 2 |
| Input Offset Voltage (max) | 1 mV (A grade) | 2 mV (standard grade) | 1 mV (A grade) |
| Output Type | Open-collector, rail-to-rail | Open-collector, rail-to-rail | Open-collector, rail-to-rail |
| Output Saturation Voltage | 200 mV at 4 mA | 200 mV at 4 mA | 200 mV at 4 mA |
| Common-Mode Input Range | Includes ground | Includes ground | Includes ground |
| Automotive Qualification | No (standard grade) | No | Yes (Q grade) |
| RoHS / Lead-Free | Compliant / lead-free | Compliant / lead-free | Compliant / lead-free |
关键差异点
- Tighter trip-point accuracy (A grade) (对比 LM2903M8-13)
- Ground-including common-mode input range (对比 LM2903AQM8-13)
- Wired-OR capable open-collector outputs (对比 LM2903M8-13)
设计说明
Always fit a pull-up resistor on each open-collector output; without it the output floats and the logic state is undefined. Size the pull-up so worst-case sink current stays near or below 4 mA, where saturation is specified at 200 mV - for a 5 V rail that means about 1.2 kOhm or higher. Route the pull-up to the logic rail the receiving device actually uses (3.3 V or 5 V), since the output high level is set by this rail, not the comparator supply.
Comparators without hysteresis chatter when the differential input crosses through the offset region, especially with slow analog ramps or noisy sensors. Add positive feedback (typically 100 kOhm to 1 MOhm from output to the non-inverting input) to impose 5-50 mV of hysteresis. Remember that the open-collector output and its pull-up form part of the hysteresis divider, so recalculate trip points after any pull-up change. RC-filter slow inputs and keep the input traces short and away from switching nodes.
Terminating an unused comparator: leave the second comparator's inputs at a defined potential (one input to a divider mid-rail, the other to ground or rail) - floating inputs can pick up noise and oscillate, increasing supply current. Also respect the differential input range: it equals the supply voltage, so inputs must never be driven beyond the rails even transiently; add series resistors (about 10 kOhm) on inputs that connect off-board. Finally, verify the supply-voltage limits in the manufacturer datasheet before using the part on industrial 24 V-derived rails.
合规信息
Per Diodes Incorporated product description: totally lead-free and fully RoHS compliant, halogen and antimony free (Green). AEC-Q100 status applies to the LM2903AQM8-13 variant, not this standard part.