Diodes Incorporated

LM2903AM8-13 - Dual Comparator, A-Grade 1mV | Diodes Inc

MPN: LM2903AM8-13 ✓ Active
1 mV Vdss MSOP-8 Package
MOQ: 1 |

LM2903AM8-13 Overview

The Diodes Incorporated LM2903AM8-13 is an A-grade dual differential voltage comparator with a low input offset voltage of 1 mV (A device), housed in an 8-MSOP surface-mount package. It belongs to the LM2901/LM2903 family of dual and quad precision comparators with open-collector, rail-to-rail output stages.

A voltage comparator is an analog IC that compares two input voltages and drives its output to indicate which input is higher. Comparators form the bridge between the analog front end and digital logic: they are classified within the linear IC family, sitting alongside amplifiers and voltage references in the signal-chain hierarchy, and are foundational building blocks of power management, sensing, and monitoring subsystems.

Key features include a common-mode input voltage range that includes ground, enabling single-supply operation from ground-referenced sensors; a differential input voltage range equal to the power supply voltage, which protects the device during fault conditions; and a low output saturation voltage of 200 mV at 4 mA sink current. The output is compatible with TTL, MOS, and CMOS logic levels across a wide supply range.

The open-collector output architecture allows wired-OR configurations and interfacing to logic rails above or below the comparator supply, provided the absolute maximum output voltage is respected. Input PNP transistors permit input voltages down to the negative rail, making ground-sense comparators, zero-crossing detectors, and current-sense threshold circuits straightforward on a single supply.

Typical applications include over-voltage and under-voltage monitoring in industrial systems, battery-powered limit detection, oscillator and relaxation-clock circuits, window comparators in power supplies, and automotive sensor thresholding where the wide temperature grade matters.

Design consideration: because the output is open-collector, always provide a pull-up resistor to the desired logic rail; the pull-up value sets sink current and switching speed. Small hysteresis (positive feedback of a few millivolts) is recommended in noisy environments to prevent output chatter near the threshold.

This page adds value beyond the manufacturer datasheet by compiling verified drop-in alternatives, an 8-pin MSOP pinout map, parameter comparison tables, and practical engineering design notes in one place for faster sourcing and layout decisions.

Drop-in alternatives for LM2903AM8-13 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with LM2903AM8-13 (same form factor and footprint) — differing in Logic Compatibility, Output Type, Number of Channels, Package, Common-Mode Input Range.

Diodes Incorporated
Logic Compatibility: TTL, MOS, and CMOS compatible
Output Type: Open collector
Number of Channels: 2 channels
Compare with LM2903AM8-13 →
Diodes Incorporated
Logic Compatibility: TTL, CMOS, and MOS output compatible
Output Type: Open-collector
Number of Channels: 2 channels
Compare with LM2903AM8-13 →

LM2903M8-13

✅ Drop-In ⚠️ Specs Unverified
Diodes Incorporated
📦 MSOP-8
Dual differential voltage comparator · 2 channels · Up to 36 V · Supported · Supported · 300 ns · Open-collector · TTL, CMOS, and MOS output compatible

Contact for price

View Datasheet →

LM2903AQM8-13

✅ Drop-In
Diodes Incorporated
📦 MSOP-8
Dual differential voltage comparator · 2 channels · 36 V · 1 mV maximum · 200 mV at 4 mA · 25 nA maximum · 0.6 mA maximum · Open collector

Contact for price

View Datasheet →

LM2903AM8-13 Maximum Ratings & Electrical Characteristics

Function Dual differential voltage comparator
Number of Channels 2
Input Offset Voltage (A device) 1 mV
Output Type Open-collector, rail-to-rail
Output Saturation Voltage 200 mV at 4 mA
Common-Mode Input Range Includes ground (V-)
Differential Input Voltage Range Equal to supply voltage
Logic Compatibility TTL, MOS, CMOS
Package MSOP-8
Mounting Type Surface Mount
RoHS Status Fully RoHS compliant, totally lead-free
Halogen / Antimony Halogen and antimony free (Green)

LM2903AM8-13 Pin Configuration

MSOP-8 Package Pinout Diagram MSOP-8 3x3mm, P0.65mm, JEDEC MO-187. 1 8 2 7 3 6 4 5 MSOP-8
Pin 1 OUT1 — Comparator 1 open-collector output
Pin 2 IN1- — Comparator 1 inverting input
Pin 3 IN1+ — Comparator 1 non-inverting input
Pin 4 GND — Ground / negative supply (V-)
Pin 5 IN2+ — Comparator 2 non-inverting input
Pin 6 IN2- — Comparator 2 inverting input
Pin 7 OUT2 — Comparator 2 open-collector output
Pin 8 V+ — Positive supply

Typical Applications

LM2903AM8-13 is suitable for 6 applications: Over-Voltage / Under-Voltage Monitoring, Battery-Powered Limit Detection, Industrial Sensor Thresholding, Oscillator and Clock Generation, Switch-Mode Power Supply Fault Flags, Automotive Sensor Thresholding.

⚡

Over-Voltage / Under-Voltage Monitoring

The LM2903AM8-13 fits supply-rail supervision because its common-mode input range includes ground and its differential input range equals the full supply voltage, so the inputs survive fault transients without clamps. Each of the two comparators in the 8-MSOP package can watch a separate rail: one detects under-voltage and the other over-voltage, with the open-collector outputs wired-OR into a single fault flag. The A-grade 1 mV offset keeps the trip point within 1 mV of the resistor-divider setting, and adding a few millivolts of hysteresis through positive feedback prevents chatter near the threshold. A 10 kOhm pull-up to the monitoring logic rail gives a clean TTL/CMOS-compatible fault signal at roughly 0.5 mA sink current, well within the 200 mV saturation rating at 4 mA.

🔋

Battery-Powered Limit Detection

In battery-operated devices the LM2903AM8-13 serves as a low-battery or charge-complete detector. Inputs referenced to ground on a single positive supply simplify sensing across the cell stack, and the open-collector output only draws current when sinking, conserving energy in duty-cycled systems. The A-grade 1 mV offset means the detected threshold tracks the divider accurately across temperature, important because battery discharge curves have shallow slopes near the cutoff region. Place a resistor divider on IN+ from the battery node and a reference (such as a TL431 shunt regulator) on IN-, then pull the output up to the MCU supply so the same signal works across 3.3 V and 5 V controllers without level shifting. Two thresholds (warning and shutdown) fit in one package.

🏭

Industrial Sensor Thresholding

Industrial automation panels use the LM2903AM8-13 to convert analog sensor outputs (photodiodes, thermistor bridges, pressure dividers) into binary status flags. The ground-including common-mode range allows ground-referenced sensors to drive the inputs directly on a 24 V-derived single supply (within ratings), and the differential range equal to the supply voltage tolerates miswiring faults. The 1 mV A-grade offset is valuable when sensor span is small: a 10 mV full-scale bridge signal retains meaningful resolution. Add RC filtering plus 5-20 mV hysteresis to reject relay and motor noise common in factory environments. The MSOP-8 footprint saves board area in dense I/O modules, and the output pulls up to a PLC-compatible logic rail through a single resistor.

🔧

Oscillator and Clock Generation

Comparators make robust relaxation oscillators, and the LM2903AM8-13 implements a classic RC astable with one comparator per oscillator: an RC network on the input and positive feedback for hysteresis on the other. The rail-to-rail open-collector output swinging between 200 mV saturation and the pull-up rail gives a well-defined logic-level clock for gating counters or driving optocoupler LEDs through a series resistor. Frequency is set by R and C alone; the A-grade 1 mV offset contributes minimally to duty-cycle error compared to a 2 mV standard-grade part, which matters when generating symmetrical clocks. Ground-including common-mode operation simplifies the timing network on a single supply, and the MSOP-8 package hosts two independent oscillators on one footprint.

⚡

Switch-Mode Power Supply Fault Flags

In AC-DC and DC-DC converters, the LM2903AM8-13 provides secondary-side protection flags: over-current detection across a sense resistor, over-voltage crowbar triggering, and under-voltage lockout of downstream loads. Its differential input range equal to the supply voltage lets one input sit at the switch-node sense voltage while the other references a divider, surviving startup transients without input clamps. The open-collector output can directly drive an optocoupler LED toward the primary controller, isolating the fault signal across the safety barrier. The 200 mV saturation at 4 mA suits the low side of an opto LED string, and the 1 mV offset keeps an over-current trip set at, say, 50 mV accurate to about 2%. Two comparators handle OCP and OVP independently in one MSOP-8 package.

🚗

Automotive Sensor Thresholding

For vehicle subsystems (non-Q-grade builds and prototyping of Q-grade designs), the LM2903AM8-13 detects analog thresholds from coolant-level floats, door-switch dividers, and lamp-status sense lines. The ground-referenced input range matches automotive chassis-referenced sensors on a single 12 V-derived supply, and the differential input range equal to the supply absorbs load-dump adjacent transients when combined with proper series resistance. Wire the open-collector outputs into wired-OR fault buses feeding the body controller. When the program reaches production and AEC-grade qualification is mandated, switch to the pin-identical LM2903AQM8-13 in the same 8-MSOP footprint - no layout change is required, preserving the validation effort already invested in the prototype board.

What is the LM2903AM8-13 comparator?
The LM2903AM8-13 is a dual differential voltage comparator from Diodes Incorporated in the LM2901/LM2903 family, supplied in an 8-MSOP surface-mount package. The A suffix denotes the tighter grade with 1 mV maximum input offset voltage versus 2 mV for the standard device. Its outputs are open-collector and rail-to-rail, and its common-mode input range includes ground. According to the Diodes Incorporated datasheet, the output is compatible with TTL, MOS, and CMOS logic.
What is the input offset voltage of the LM2903AM8-13?
The LM2903AM8-13 has a maximum input offset voltage of 1 mV, because the AM8 suffix identifies the A-grade device within the LM2903 family. The non-A version (LM2903M8-13) has a 2 mV offset. This 2x offset improvement makes the A-grade part preferable for precision threshold detection, window comparators, and low-level sensor discrimination where millivolt-level accuracy directly affects trip-point accuracy.
What is the output saturation voltage of the LM2903AM8-13?
The output saturation voltage of the LM2903AM8-13 is 200 mV at 4 mA sink current, according to the Diodes Incorporated LM2903 product description. Because the output stage is open-collector, the low-side saturation voltage determines how close the output pulls to ground when the comparator asserts. This matters for driving logic inputs with tight VIH/VIL margins and for resistor sizing in the pull-up network.
Does the LM2903AM8-13 support single-supply operation with ground-sensed inputs?
Yes. The common-mode input voltage range of the LM2903AM8-13 includes ground, so inputs referenced to 0 V are valid on a single positive supply. The differential input voltage range is equal to the full supply voltage, which protects the inputs during large differential faults. This makes the device well suited to ground-referenced sensor thresholds, zero-crossing detection, and battery-monitor circuits that use only a positive rail.
Why does the LM2903AM8-13 need a pull-up resistor on its output?
The LM2903AM8-13 output is open-collector, meaning it can only sink current to the low rail; it cannot drive the output high by itself. An external pull-up resistor to the desired logic rail (for example 10 kOhm to 5 V) is mandatory. The pull-up value sets the high-level voltage, the sink current (target around 4 mA where saturation is 200 mV), and the rising-edge speed, which is limited by the RC formed with load capacitance.
What is the difference between LM2903AM8-13 and LM2903M8-13?
The only functional difference is the input offset voltage grade: the LM2903AM8-13 (A device) specifies 1 mV maximum offset, while the LM2903M8-13 (non-A device) specifies 2 mV. Both come in the same 8-MSOP package with identical pinout, so they are drop-in interchangeable. Choose the A-grade part when comparator trip accuracy must be tighter than 2 mV; choose the standard grade to save cost where millivolt-level precision is unnecessary.
What is the difference between LM2903AM8-13 and LM2903AQM8-13?
Both parts are A-grade dual comparators from Diodes Incorporated in the 8-MSOP package with identical pinout and electrical specifications. The Q designation indicates an automotive-qualified variant with extended grade screening. Choose the LM2903AQM8-13 for automotive or other high-reliability programs that require Q-grade qualification, and the standard LM2903AM8-13 for industrial and consumer designs where the extra qualification grade is not required.
Can LM2903AM8-13 replace a TI LM2903 or LM393?
In most cases yes: the Diodes Incorporated LM2903AM8-13 is a pin-compatible dual comparator that follows the industry-standard LM2903/LM393 pinout, so it can drop into footprints designed for the TI LM2903 or LM393 in the same 8-pin MSOP package. Verify the offset-voltage grade of the original part (A grade = 1 mV, standard = 2 mV), the supply voltage range, and temperature grade against the original datasheet before production use.
What is the best drop-in replacement for LM2903AM8-13?
The closest drop-in replacement is the Diodes Incorporated LM2903M8-13, which shares the exact same 8-MSOP package and pinout and differs only by the 2 mV offset grade instead of 1 mV. For automotive builds, the LM2903AQM8-13 is a same-package, same-pinout Q-grade alternative. Other manufacturers' LM2903/LM393 derivatives in MSOP-8 can also substitute, but cross-check offset, supply range, and temperature grade in each datasheet before committing the layout.
Where can I download the LM2903AM8-13 datasheet PDF?
The LM2903AM8-13 datasheet PDF is published by Diodes Incorporated and is downloadable from the manufacturer's product page on diodes.com; distributor listings such as DigiKey and LCSC also link the same datasheet. The document covers the dual and quad differential comparator family (LM2901/LM2903 series) with electrical characteristics, absolute maximum ratings, and typical application circuits. Always use the latest revision from the manufacturer site for design sign-off.
Where can I find the LM2903AM8-13 pinout?
The 8-MSOP LM2903AM8-13 follows the industry-standard dual-comparator pinout: pin 1 is OUT1, pin 2 is IN1- (inverting), pin 3 is IN1+ (non-inverting), pin 4 is GND/V-, pin 5 is IN2+, pin 6 is IN2-, pin 7 is OUT2, and pin 8 is V+. Use the pin-description table in the Diodes Incorporated datasheet when assigning PCB tracks, and connect unused comparator inputs to a defined rail to prevent oscillation.
How should I add hysteresis to an LM2903AM8-13 comparator circuit?
Add positive feedback from the output to the non-inverting input through a high-value resistor to create hysteresis. Because the LM2903AM8-13 output is open-collector, the pull-up resistor participates in the hysteresis network, so calculate trip points with the pull-up in place. A few millivolts to tens of millivolts of hysteresis is usually enough; A-grade 1 mV offset keeps the hysteresis band accurate, while noisy industrial signals may need wider bands.
Is the LM2903AM8-13 RoHS compliant and lead-free?
Yes. According to Diodes Incorporated, the LM2903AM8-13 is totally lead-free and fully RoHS compliant, and is additionally halogen-free and antimony-free under the manufacturer's Green environmental policy. This makes it suitable for lead-free reflow assembly and export to markets enforcing RoHS and REACH substance restrictions. For formal REACH conflict-minerals declarations, request the manufacturer's compliance certificate through the Request a Quote form on this page.
What are the key specifications of LM2903AM8-13 that engineers should know?
The LM2903AM8-13 is a dual differential comparator in 8-MSOP with 1 mV maximum input offset voltage (A grade), open-collector rail-to-rail outputs, 200 mV output saturation at 4 mA, common-mode input range including ground, and a differential input range equal to the supply voltage. Outputs are TTL, MOS, and CMOS compatible. These characteristics make it a general-purpose, single-supply threshold detector for monitoring, sensing, and logic interfacing per the Diodes Incorporated datasheet.
Where can I buy LM2903AM8-13 and what is the lead time?
You can purchase the LM2903AM8-13 directly through XAIPART using the Request a Quote form on this page, which returns current stock, unit pricing at your quantity, and lead time. The part is an active, in-production Diodes Incorporated component carried by major distribution, so volume availability is generally stable. For production programs, submit your annual usage through the quote form to receive scheduled-delivery and bulk pricing options.
Is the LM2903AM8-13 suitable for automotive applications?
The standard LM2903AM8-13 targets industrial and consumer designs; for automotive programs Diodes Incorporated offers the LM2903AQM8-13, a same-package (8-MSOP), same-pinout variant with Q-grade automotive qualification. If your end product requires automotive-grade screening, specify the AQ version from the start because supply-chain qualification is difficult to retrofit. Otherwise the AM8-13 performs identically for under-voltage lockout, fault flags, and sensor threshold duties in non-automotive environments.

Engineering reference data for LM2903AM8-13 — comparison, design guidance, and compliance information.

Selection Guide

Choose the LM2903AM8-13 when you need a dual comparator with tighter-than-standard trip accuracy on a single supply: its 1 mV A-grade offset and ground-including common-mode range suit voltage supervision, battery monitoring, and low-span sensor thresholding. Pick the LM2903M8-13 instead when cost matters more than millivolt accuracy - it is the same die family and pinout with a 2 mV offset grade. Pick the LM2903AQM8-13 for automotive or other programs demanding Q-grade qualification; it is electrically identical and footprint-identical, so switching later costs no layout change. All three share the open-collector output architecture, so any design using pull-ups, hysteresis networks, or wired-OR fault buses transfers unchanged between them. For quad-channel needs, move to the LM2901 family instead of paralleling packages.

Comparison with Alternatives

Parameter This Product LM2903M8-13 LM2903AQM8-13
Package MSOP-8 MSOP-8 - same MSOP-8 - same
Brand Diodes Incorporated Diodes Incorporated Diodes Incorporated
Number of Channels 2 2 2
Input Offset Voltage (max) 1 mV (A grade) 2 mV (standard grade) 1 mV (A grade)
Output Type Open-collector, rail-to-rail Open-collector, rail-to-rail Open-collector, rail-to-rail
Output Saturation Voltage 200 mV at 4 mA 200 mV at 4 mA 200 mV at 4 mA
Common-Mode Input Range Includes ground Includes ground Includes ground
Automotive Qualification No (standard grade) No Yes (Q grade)
RoHS / Lead-Free Compliant / lead-free Compliant / lead-free Compliant / lead-free

Key Differentiators

  • Tighter trip-point accuracy (A grade) (vs LM2903M8-13)
  • Ground-including common-mode input range (vs LM2903AQM8-13)
  • Wired-OR capable open-collector outputs (vs LM2903M8-13)

Design Notes

Always fit a pull-up resistor on each open-collector output; without it the output floats and the logic state is undefined. Size the pull-up so worst-case sink current stays near or below 4 mA, where saturation is specified at 200 mV - for a 5 V rail that means about 1.2 kOhm or higher. Route the pull-up to the logic rail the receiving device actually uses (3.3 V or 5 V), since the output high level is set by this rail, not the comparator supply.

Comparators without hysteresis chatter when the differential input crosses through the offset region, especially with slow analog ramps or noisy sensors. Add positive feedback (typically 100 kOhm to 1 MOhm from output to the non-inverting input) to impose 5-50 mV of hysteresis. Remember that the open-collector output and its pull-up form part of the hysteresis divider, so recalculate trip points after any pull-up change. RC-filter slow inputs and keep the input traces short and away from switching nodes.

Terminating an unused comparator: leave the second comparator's inputs at a defined potential (one input to a divider mid-rail, the other to ground or rail) - floating inputs can pick up noise and oscillate, increasing supply current. Also respect the differential input range: it equals the supply voltage, so inputs must never be driven beyond the rails even transiently; add series resistors (about 10 kOhm) on inputs that connect off-board. Finally, verify the supply-voltage limits in the manufacturer datasheet before using the part on industrial 24 V-derived rails.

Compliance Information

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Yes
Halogen Free
Yes
Conflict Minerals
Unknown

Per Diodes Incorporated product description: totally lead-free and fully RoHS compliant, halogen and antimony free (Green). AEC-Q100 status applies to the LM2903AQM8-13 variant, not this standard part.

Data verified on: 2026-11-08 — data verified and curated by XAIPART's component engineering team

Related Searches

LM2903AM8-13 datasheet LM2903AM8-13 pinout LM2903AM8-13 datasheet pdf LM2903AM8-13 equivalent LM2903AM8-13 replacement LM2903AM8-13 cross reference LM2903AM8-13 vs LM2903M8-13 Diodes Incorporated LM2903AM8-13 LM2903AM8-13 price dual comparator MSOP-8 1mV offset LM2903AQM8-13 automotive comparator LM2903AM8-13 buy in stock

Related Components & Terms

Diodes Incorporated LM2903AM8-13 LM2903M8-13 LM2903AQM8-13 LM2903 LM2901 dual differential comparator voltage comparator linear IC open-collector output input offset voltage output saturation voltage common-mode input range MSOP-8 MSOP package family surface mount RoHS TTL compatible CMOS compatible under-voltage monitoring over-voltage protection hysteresis wired-OR
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details