LM2903N/NOPB - 36V Dual Open-Collector Comparator | TI
料号: LM2903N/NOPB ✓ 量产中LM2903N/NOPB 概述
A comparator is a signal-conditioning semiconductor that evaluates two input voltages and produces a logic-level result indicating which input is higher. A dual differential comparator combines two independent comparison channels in one package. The LM2903 belongs to the broader comparator and amplifier IC hierarchy and is designed for single-supply operation, split-supply operation, and interfaces where an open-collector output can directly drive pull-up resistors.
The principal features include low offset voltage, low power consumption, and open-collector outputs. Open-collector outputs can sink current while remaining in a high-impedance state when inactive, allowing the output transition speed and logic level to be set by an external pull-up network. The two channels operate independently, supporting simultaneous comparison, level detection, window monitoring, or dual-threshold functions in one circuit.
The Texas Instruments LM2903-N family is specified for operation from a single supply across a wide voltage range, with an operating range extending to 36 V. The 2 mV maximum offset specification is useful when the comparator must resolve small voltage differences. Its 1.3 microsecond response is suitable for general-purpose industrial control, monitoring, and interface circuits rather than ultra-high-speed signal comparison.
Typical applications include industrial sensor interfaces, overvoltage and undervoltage detection, battery threshold monitoring, temperature-control loops, and general digital logic interfaces. The open-drain architecture also allows wired logic, alarm aggregation, and level-shifting arrangements when suitable pull-up resistors are provided.
For reliable PCB implementation, place the input and output components close to the device and provide a defined pull-up resistor on each open-collector output. Check the output sink-current limit, input common-mode range, supply decoupling, and unused-channel configuration against the manufacturer datasheet before finalizing the design.
This product page combines the exact orderable part information, package information, comparator characteristics, drop-in candidate analysis, and application-focused engineering guidance to support faster component selection and board-level implementation.
直接替换替代料: LM2903N/NOPB ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2903N/NOPB (相同外形与封装尺寸) ——差异在于 Output Type, Package, Comparator Type, Input Offset Voltage, Operating Temperature Range.
LM2903N/NOPB 最大额定值与电气特性
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| 输出类型 | Open collector / open drain |
| Maximum Supply Voltage | 36 V |
| Input Offset Voltage | 2 mV maximum |
| Propagation Delay | 1.3 microseconds |
| 工作温度范围 | -40°C to 85°C |
| 封装 | 8-pin PDIP (P) |
| 引脚数量 | 8 pins |
| 安装类型 | Through-hole |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | unknown |
LM2903N/NOPB 8-pin pdip (p) 引脚配置指南
LM2903N/NOPB(8-pin pdip (p) 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM2903N/NOPB.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM2903N/NOPB 适用于 6 应用s: Industrial Sensor Threshold Detection, Battery Overvoltage and Undervoltage Monitoring, Temperature-Control Loop Comparison, Digital Logic Interface and Level Detection, Motor and Solenoid Driver Interlock, Wired-Logic and Alarm Aggregation.
Industrial Sensor Threshold Detection
The LM2903N/NOPB fits industrial sensor interfaces that compare a conditioned measurement against a reference voltage. Its two independent channels can monitor two thresholds, while the stated 2 mV maximum input offset voltage supports decisions involving relatively small voltage differences. The device operates across a -40°C to 85°C range, making it appropriate for equipment exposed to moderate industrial temperature variation. Each open-collector output can directly pull a control or alarm line low, with an external pull-up setting the opposite logic state. Designers should verify that the sensor voltage remains inside the comparator's specified common-mode range and allow for output rise time when calculating alarm response time.
推荐
Battery Overvoltage and Undervoltage Monitoring
The LM2903N/NOPB can supervise a battery or DC rail by comparing its voltage against a reference in each of its two channels. The 36 V maximum supply rating provides margin for industrial battery systems while the dual architecture supports separate overvoltage and undervoltage decisions. Open-collector outputs allow fault signals to be combined or pulled up to the logic voltage used by a monitoring controller. In this implementation, resistor tolerances and reference accuracy can dominate the effective switching threshold, so the 2 mV maximum offset specification should be treated as one error contributor rather than the complete threshold budget. Confirm the input common-mode range across the full battery voltage excursion.
推荐
Temperature-Control Loop Comparison
The LM2903N/NOPB is suitable for a basic temperature-control loop in which a sensor amplifier output is compared with a setpoint. One differential channel can determine whether the measured temperature is above or below the commanded value, while the other channel can monitor a redundant limit. Its 1.3 microsecond propagation delay is short compared with typical thermal-loop response times, allowing switching behavior to follow the sensed condition without becoming the dominant lag. The open-drain output can drive a relay-driver input, a logic gate, or an optocoupler control stage through a suitable pull-up network. Thermal stability of the external reference and feedback components remains important when the target switching point requires high accuracy.
推荐
Digital Logic Interface and Level Detection
The LM2903N/NOPB can act as a robust logic-level interface between an analog voltage domain and a digital control system. Its open-collector output provides straightforward active-low signaling: the output transistor pulls the line low when the comparison changes state, while a pull-up resistor establishes the high level. The dual-channel configuration can evaluate two unrelated signals or implement a window detector using external references. This arrangement is useful for interlock logic, digital enable signals, and simple alarm inputs. Because the output does not actively source current, the pull-up voltage must remain within the device's output ratings, and the selected resistor must satisfy both sink-current and rise-time requirements under the intended load.
推荐
Motor and Solenoid Driver Interlock
The LM2903N/NOPB can supervise motor, solenoid, or actuator control signals by comparing a command or feedback voltage against a reference. The 36 V maximum supply rating accommodates industrial control environments, and the open-collector output can provide an active-low interlock or fault indication to a controller. Its two channels can separately validate an enable command and a feedback condition, improving system safety checks before a power stage operates. The comparator itself does not provide the motor drive current or isolation required for a power actuator; it is best used ahead of a suitable driver. Layout should keep the sensing node away from high-current switching paths to prevent ground bounce from changing the decision near the threshold.
推荐
Wired-Logic and Alarm Aggregation
The LM2903N/NOPB is well suited to open-drain alarm and fault signals because multiple comparator outputs can share a common pull-up when wired in parallel. Two channels can monitor separate fault conditions and combine them into one active-low summary line for a system controller. This arrangement reduces the number of controller inputs while retaining individual fault diagnosis elsewhere. The 1.3 microsecond propagation delay supports prompt fault recognition, although the shared pull-up creates a tradeoff between rise time, power dissipation, and the number of simultaneously asserted outputs. Check the datasheet's sink-current limit and ensure that every attached output remains off during normal operation so the common line is not unintentionally pulled low.
推荐
推荐产品汇总
工程参考数据: LM2903N/NOPB ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2903N |
|---|---|---|
| Brand | Texas Instruments | onsemi |
| Package | 8-pin PDIP (P) | 8-DIP - same footprint class |
| Comparator Channels | 2 channels | 2 channels |
| Output Type | Open collector / open drain | Open collector / open drain |
关键差异点
- Dual independent low-offset comparison channels (对比 LM2903N)
- High-voltage open-collector operation (对比 LM2903N)
- Through-hole integration in an 8-pin PDIP (对比 LM2903N)
设计说明
Do not treat the open-collector output as a push-pull logic output. Fit a pull-up resistor on every comparator output so the line has a defined high voltage when the output transistor is off. Select the resistor using the required logic level, output sink-current limit, propagation delay, and allowable rise time. If two outputs are wired in parallel for fault aggregation, verify that both channels remain inactive during a normal system state.
Keep the comparator inputs, feedback divider, and reference components close to the package to minimize pickup from adjacent switching circuits. Place the input bypass capacitor at the supply pin and maintain a quiet return path for the comparator ground. High-current relay, motor, and power-converter returns should not share narrow PCB traces with the sensing reference because ground bounce can shift the decision point.
The 36 V rating is a maximum operating limit, not a recommendation to operate continuously at 36 V. Derive the actual dissipation from the supply voltage, output sinking duty cycle, and the PCB thermal environment. When an open output is high-impedance, the pull-up resistor may continue to dissipate power, so calculate both the comparator output-device loss and resistor loading before selecting the external network.
For low-level sensor comparisons, account for offset voltage, resistor tolerances, reference drift, and input noise as separate contributors to switching-point error. The specified 2 mV maximum offset is only one part of that error budget. Apply hysteresis when the comparator output must not chatter around a slow or noisy threshold, and verify that the feedback component selected for hysteresis does not exceed the output and input limits.
合规信息
The exact LM2903N/NOPB orderable-part listing does not state the requested compliance classifications. The NOPB packaging suffix was not used as a substitute for an explicit compliance statement.