LM2903WHYST - Dual Low-Power Voltage Comparator | STMicroelectronics
料号: LM2903WHYST ✓ 量产中LM2903WHYST 概述
A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The dual comparator in the LM2903WHYST can perform two independent threshold, window, or level-detection functions. In the power-management hierarchy, this device belongs to the comparator family within amplifier and signal-conditioning integrated circuits. It is intended for low-power sensing where the output must interface with TTL, CMOS, or other digital logic.
The principal electrical features include a wide single-supply range of 2 V to 36 V, dual-supply operation from ±1 V to ±18 V, and very low supply current of 0.4 mA independent of supply voltage. The manufacturer documentation also lists a typical input bias current of 25 nA, typical input offset current of ±5 nA, an input common-mode range that includes the negative rail, and a typical low output saturation voltage of 250 mV at 4 mA output current. Each comparator consumes approximately 1 mW when operated from 5 V.
The open-collector architecture requires an external pull-up resistor. When the output transistor turns off, the resistor raises the output toward the logic supply; when it turns on, the output is pulled toward ground. The differential input voltage can be large enough for the comparator to be used as a Schmitt trigger or line receiver, while the low quiescent current supports battery-powered equipment. Open-collector outputs can also be wired together, but the resulting common output requires careful pull-up selection and fault-current analysis.
Typical uses include industrial sensor interfaces, battery monitoring, overvoltage and undervoltage detection, motor-control thresholds, and general logic-level sensing. The LM2903WHYST is particularly appropriate where two independent decisions are required and where a low-current open-drain interface is preferable to a rail-to-rail push-pull output. In a battery-powered design, the 0.4 mA supply current helps limit continuous overhead, while the broad supply range supports operation from low-voltage cells through industrial rails.
Designers should select the external pull-up resistor according to the required logic level, output rise time, and leakage current. The pull-up must connect to a supply that remains within the output ratings of the comparator and the receiving logic device. Input source impedance should remain low enough to prevent bias-current-induced offset errors, and unused comparator channels should be configured according to the manufacturer recommendations rather than left floating.
This product page combines the manufacturer's electrical characteristics with package, application, and replacement guidance. It also identifies verified same-package alternatives where pin compatibility can be established, helping engineers shorten qualification work while preserving the electrical behavior of the original LM2903WHYST design.
直接替换替代料: LM2903WHYST ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2903WHYST (相同外形与封装尺寸) ——差异在于 Comparator Type, Package, Supply Current.
LM2903WH
✅ 直接替换📋 参考替代料(不在目录中)
LM2903VQDRG4Q1
✅ 直接替换联系询价
查看数据手册 →LM2903DT
✅ 直接替换📋 参考替代料(不在目录中)
LM2903M
✅ 直接替换联系询价
查看数据手册 →LM2903DQ
✅ 直接替换📋 参考替代料(不在目录中)
LM2903WHYST 最大额定值与电气特性
| Comparator Type | 2 independent voltage comparators |
| Single-Supply Voltage Range | 2 V to 36 V |
| Dual-Supply Voltage Range | ±1 V to ±18 V |
| 电源电流 | 0.4 mA typical, independent of supply voltage |
| Power Consumption Per Comparator | 1 mW at 5 V |
| Input Bias Current | 25 nA typical |
| Input Offset Current | ±5 nA typical |
| Input Common-Mode Range | Includes the negative supply rail |
| Low Output Saturation Voltage | 250 mV typical at 4 mA output current |
| Output Architecture | Open-collector |
| Output Interface | Compatible with TTL and CMOS logic |
| Number of Channels | 2 |
| 封装 | 8-MiniSO |
| 安装类型 | Surface mount |
LM2903WHYST 引脚配置
| 引脚 1 | OUT 1 — Comparator 1 open-collector output |
| 引脚 2 | IN− 1 — Comparator 1 inverting input |
| 引脚 3 | IN+ 1 — Comparator 1 non-inverting input |
| 引脚 4 | GND — Ground connection |
| 引脚 5 | IN+ 2 — Comparator 2 non-inverting input |
| 引脚 6 | IN− 2 — Comparator 2 inverting input |
| 引脚 7 | OUT 2 — Comparator 2 open-collector output |
| 引脚 8 | VCC — Positive supply connection |
典型应用
LM2903WHYST 适用于 6 应用s: Battery Voltage Threshold Detection, Industrial Sensor Interfacing, Overvoltage and Undervoltage Protection, Motor Control and Driver Interface, Logic-Level and Signal Crossing Detection, Low-Power Monitoring and Control.
Battery Voltage Threshold Detection
The LM2903WHYST is suitable for monitoring a battery pack when low power and a negative-rail-inclusive common-mode range are important. One channel can compare the pack voltage with a precision reference while the other monitors a scaled system rail. Its 0.4 mA typical supply current is independent of supply voltage, and the manufacturer specifies approximately 1 mW per comparator at 5 V. An open-collector output can directly pull up to a low-power logic rail, allowing the controller input to remain active during shutdown. The key design consideration is selecting the divider and reference so that offset, bias current, and input leakage do not shift the intended threshold.
推荐
Industrial Sensor Interfacing
The LM2903WHYST can compare a sensor output with an adjustable threshold in industrial monitoring equipment. Its two independent channels support separate sensing tasks, while the 2 V to 36 V single-supply range accommodates low-voltage sensor rails and higher industrial supplies. The input bias current is 25 nA typical, helping minimize loading on high-impedance sensor networks, and the input offset current is ±5 nA typical. Because the output is open-collector, a pull-up resistor allows the interface to operate at the voltage expected by PLC, MCU, or other digital logic. Keep comparator inputs away from switching nodes and use a stable reference when threshold repeatability is important.
推荐
Overvoltage and Undervoltage Protection
The LM2903WHYST supports two-rail supervision by assigning one comparator channel to overvoltage detection and the other to undervoltage detection. Its wide 2 V to 36 V operating range permits the comparator itself to remain active across widely varying supply conditions. The low 0.4 mA typical supply current reduces supervisory overhead in portable equipment, while the negative-rail-inclusive common-mode range supports low-side and ground-referenced sensing arrangements. Open-collector outputs can be wired together for a combined fault indication if the pull-up and fault-current design permits. For safety-critical decisions, include resistor tolerance, reference accuracy, and propagation delay in the threshold-error budget.
推荐
Motor Control and Driver Interface
The LM2903WHYST can compare a motor-control signal or current-sense amplifier output against a limit and then drive a fault input or protection logic. The open-collector output supports wired-AND fault signaling, while the two channels can monitor different limits independently. Its low supply current is useful in continuously powered motor-control systems, and the common-mode input range includes the negative rail, which simplifies ground-referenced sensing. The design must account for electrical noise around motor switching nodes, maintain adequate separation between sensitive comparator inputs and power paths, and select pull-up values that satisfy the receiving logic's rise-time requirements. A low saturation voltage of 250 mV typical at 4 mA helps preserve logic-level recognition.
推荐
Logic-Level and Signal Crossing Detection
The LM2903WHYST can act as a signal-crossing detector between two analog domains by comparing a sensed voltage with a threshold and driving an open-collector logic output. Its 25 nA typical input bias current minimizes disturbance of high-impedance signal sources, while the 2 V to 36 V supply range provides broad operating flexibility. The external pull-up may reference a different logic supply from the comparator, enabling level translation without a dedicated translator IC. For noisy or slow-changing signals, positive feedback can add hysteresis and suppress repeated transitions. Confirm that the input common-mode voltage and differential voltage remain within the limits published in the LM2903W datasheet.
推荐
Low-Power Monitoring and Control
The LM2903WHYST fits low-power monitoring systems that require local threshold decisions without a continuously operating digital controller. Its 0.4 mA typical supply current is independent of the supply voltage, and each comparator consumes approximately 1 mW at 5 V according to the manufacturer documentation. Two channels can supervise local conditions and wake or inhibit downstream circuitry through open-collector pull-ups. The device can also implement a simple window comparator using two reference inputs and externally wired outputs. For low-duty-cycle systems, validate the quiescent current over the full expected supply range and ensure that pull-up resistors do not dominate the standby power budget.
推荐
推荐产品汇总
工程参考数据: LM2903WHYST ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2903WH | LM2903VQDRG4Q1 | LM2903DT | LM2903M | LM2903DQ |
|---|---|---|---|---|---|---|
| Package | 8-MiniSO | 8-MiniSO | 8-MiniSO | 8-MiniSO | 8-MiniSO | 8-MiniSO |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | 3PEAK |
| Comparator Channels | 2 independent comparators | 2 independent comparators | 2 independent comparators | 2 independent comparators | 2 independent comparators | 2 independent comparators |
| Output Architecture | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
关键差异点
- Wide single-supply operating range (对比 LM2903DQ)
- Very low supply current independent of supply voltage (对比 LM2903M)
- Low input bias and offset currents (对比 LM2903DT)
- Negative-rail-inclusive common-mode input range (对比 LM2903DQ)
- Automotive-focused family option (对比 LM2903WH)
设计说明
Do not treat the open-collector output as a push-pull logic output. Install an external pull-up resistor on each comparator output and connect it to the voltage required by the receiving device. If both outputs are tied together, size the shared pull-up for the maximum combined sink current and ensure that the resulting rise time meets the receiving circuit's timing requirements.
Estimated: the LM2903WHYST supply-current dissipation at 5 V is approximately 0.4 mA × 5 V = 2 mW for the complete dual device, consistent with the manufacturer's 1 mW per comparator figure. Add pull-up-resistor current and any connected logic load when calculating total power. This estimate does not include dynamic output-transition or external-reference current.
Route the two comparator channels to keep sensitive input traces away from switching nodes, motor phases, inductors, and high-current return paths. Use a continuous ground reference beneath the inputs and place the output pull-up resistor close to the comparator pin or receiving input. High-impedance divider nodes should have minimal copper area to reduce leakage and noise pickup.
For slowly changing or noisy inputs, add controlled positive feedback to create Schmitt-trigger hysteresis. Calculate the hysteresis from the resistor network while confirming that both inputs remain inside the common-mode range under all supply conditions. Also ensure that source impedance is low enough that input bias current and offset current do not materially shift the switching threshold.
合规信息
The manufacturer documentation describes ECOPACK options by environmental grade, but a specific compliance declaration for the LM2903WHYST ordering code could not be established from the cited product information.