STMicroelectronics

LM2903WHYST - Dual Low-Power Voltage Comparator | STMicroelectronics

MPN: LM2903WHYST ✓ فعال
2 V to 36 V Vdss 0.4 mA typical, independent of supply voltage Id 8-MiniSO Package
حداقل سفارش: 1 |

LM2903WHYST نمای کلی

The STMicroelectronics LM2903WHYST is a low-power dual voltage comparator containing two independent comparator channels, a 2 V to 36 V single-supply operating range, and an 8-MiniSO package. Each channel provides an open-collector output, allowing the outputs to be pulled up to a compatible logic supply and used in wired-AND arrangements when connected together.

A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The dual comparator in the LM2903WHYST can perform two independent threshold, window, or level-detection functions. In the power-management hierarchy, this device belongs to the comparator family within amplifier and signal-conditioning integrated circuits. It is intended for low-power sensing where the output must interface with TTL, CMOS, or other digital logic.

The principal electrical features include a wide single-supply range of 2 V to 36 V, dual-supply operation from ±1 V to ±18 V, and very low supply current of 0.4 mA independent of supply voltage. The manufacturer documentation also lists a typical input bias current of 25 nA, typical input offset current of ±5 nA, an input common-mode range that includes the negative rail, and a typical low output saturation voltage of 250 mV at 4 mA output current. Each comparator consumes approximately 1 mW when operated from 5 V.

The open-collector architecture requires an external pull-up resistor. When the output transistor turns off, the resistor raises the output toward the logic supply; when it turns on, the output is pulled toward ground. The differential input voltage can be large enough for the comparator to be used as a Schmitt trigger or line receiver, while the low quiescent current supports battery-powered equipment. Open-collector outputs can also be wired together, but the resulting common output requires careful pull-up selection and fault-current analysis.

Typical uses include industrial sensor interfaces, battery monitoring, overvoltage and undervoltage detection, motor-control thresholds, and general logic-level sensing. The LM2903WHYST is particularly appropriate where two independent decisions are required and where a low-current open-drain interface is preferable to a rail-to-rail push-pull output. In a battery-powered design, the 0.4 mA supply current helps limit continuous overhead, while the broad supply range supports operation from low-voltage cells through industrial rails.

Designers should select the external pull-up resistor according to the required logic level, output rise time, and leakage current. The pull-up must connect to a supply that remains within the output ratings of the comparator and the receiving logic device. Input source impedance should remain low enough to prevent bias-current-induced offset errors, and unused comparator channels should be configured according to the manufacturer recommendations rather than left floating.

This product page combines the manufacturer's electrical characteristics with package, application, and replacement guidance. It also identifies verified same-package alternatives where pin compatibility can be established, helping engineers shorten qualification work while preserving the electrical behavior of the original LM2903WHYST design.

جایگزین‌های drop-in برای LM2903WHYST — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای LM2903WHYST (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Comparator Type, Package, Supply Current.

Texas Instruments
Comparator Type: Dual differential comparator
Package: 8-pin SOIC
Supply Current: 1 mA
مقایسه با LM2903WHYST →

LM2903WH

✅ جایگزین مستقیم
📦 8-MiniSO
Same LM2903WH family, 2 V to 36 V supply range, and 8-MiniSO footprint; the ordering suffix determines grade and packing details

📋 جایگزین مرجع (خارج از کاتالوگ)

LM2903VQDRG4Q1

✅ جایگزین مستقیم
Texas Instruments
📦 8-MiniSO
Dual differential voltage comparator · 2 channels · 2 V to 36 V · ±1 V to ±18 V · Open-collector, rail-to-rail · 0.4 mA typical per comparator · 0.3 us · AEC-Q100 Grade 0 and Grade 1

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

LM2903DT

✅ جایگزین مستقیم
📦 8-MiniSO
Same LM2903 dual-comparator electrical family, but ordering code differs in temperature grade and packaging

📋 جایگزین مرجع (خارج از کاتالوگ)

LM2903M

✅ جایگزین مستقیم
Texas Instruments
📦 8-MiniSO
Dual differential comparator · 2 · 2 V to 36 V · Open-collector · Rail-to-rail · 1.5 microseconds · 1 mA · CMOS, DTL, ECL, MOS, TTL

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

LM2903DQ

✅ جایگزین مستقیم
📦 8-MiniSO
Dual open-collector comparator with common-mode input range including ground and low supply current; manufacturer differs

📋 جایگزین مرجع (خارج از کاتالوگ)

LM2903WHYST حداکثر مقادیر مجاز و مشخصات الکتریکی

Comparator Type 2 independent voltage comparators
Single-Supply Voltage Range 2 V to 36 V
Dual-Supply Voltage Range ±1 V to ±18 V
جریان تغذیه 0.4 mA typical, independent of supply voltage
Power Consumption Per Comparator 1 mW at 5 V
Input Bias Current 25 nA typical
Input Offset Current ±5 nA typical
Input Common-Mode Range Includes the negative supply rail
Low Output Saturation Voltage 250 mV typical at 4 mA output current
Output Architecture Open-collector
Output Interface Compatible with TTL and CMOS logic
Number of Channels 2
بسته‌بندی 8-MiniSO
نوع نصب Surface mount

پیکربندی پین LM2903WHYST

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 OUT 1 — Comparator 1 open-collector output
پین 2 IN− 1 — Comparator 1 inverting input
پین 3 IN+ 1 — Comparator 1 non-inverting input
پین 4 GND — Ground connection
پین 5 IN+ 2 — Comparator 2 non-inverting input
پین 6 IN− 2 — Comparator 2 inverting input
پین 7 OUT 2 — Comparator 2 open-collector output
پین 8 VCC — Positive supply connection

کاربردهای معمول

LM2903WHYST مناسب است برای 6 کاربردs: Battery Voltage Threshold Detection, Industrial Sensor Interfacing, Overvoltage and Undervoltage Protection, Motor Control and Driver Interface, Logic-Level and Signal Crossing Detection, Low-Power Monitoring and Control.

🔋

Battery Voltage Threshold Detection

The LM2903WHYST is suitable for monitoring a battery pack when low power and a negative-rail-inclusive common-mode range are important. One channel can compare the pack voltage with a precision reference while the other monitors a scaled system rail. Its 0.4 mA typical supply current is independent of supply voltage, and the manufacturer specifies approximately 1 mW per comparator at 5 V. An open-collector output can directly pull up to a low-power logic rail, allowing the controller input to remain active during shutdown. The key design consideration is selecting the divider and reference so that offset, bias current, and input leakage do not shift the intended threshold.

🏭

Industrial Sensor Interfacing

The LM2903WHYST can compare a sensor output with an adjustable threshold in industrial monitoring equipment. Its two independent channels support separate sensing tasks, while the 2 V to 36 V single-supply range accommodates low-voltage sensor rails and higher industrial supplies. The input bias current is 25 nA typical, helping minimize loading on high-impedance sensor networks, and the input offset current is ±5 nA typical. Because the output is open-collector, a pull-up resistor allows the interface to operate at the voltage expected by PLC, MCU, or other digital logic. Keep comparator inputs away from switching nodes and use a stable reference when threshold repeatability is important.

⚡

Overvoltage and Undervoltage Protection

The LM2903WHYST supports two-rail supervision by assigning one comparator channel to overvoltage detection and the other to undervoltage detection. Its wide 2 V to 36 V operating range permits the comparator itself to remain active across widely varying supply conditions. The low 0.4 mA typical supply current reduces supervisory overhead in portable equipment, while the negative-rail-inclusive common-mode range supports low-side and ground-referenced sensing arrangements. Open-collector outputs can be wired together for a combined fault indication if the pull-up and fault-current design permits. For safety-critical decisions, include resistor tolerance, reference accuracy, and propagation delay in the threshold-error budget.

🔧

Motor Control and Driver Interface

The LM2903WHYST can compare a motor-control signal or current-sense amplifier output against a limit and then drive a fault input or protection logic. The open-collector output supports wired-AND fault signaling, while the two channels can monitor different limits independently. Its low supply current is useful in continuously powered motor-control systems, and the common-mode input range includes the negative rail, which simplifies ground-referenced sensing. The design must account for electrical noise around motor switching nodes, maintain adequate separation between sensitive comparator inputs and power paths, and select pull-up values that satisfy the receiving logic's rise-time requirements. A low saturation voltage of 250 mV typical at 4 mA helps preserve logic-level recognition.

🌐

Logic-Level and Signal Crossing Detection

The LM2903WHYST can act as a signal-crossing detector between two analog domains by comparing a sensed voltage with a threshold and driving an open-collector logic output. Its 25 nA typical input bias current minimizes disturbance of high-impedance signal sources, while the 2 V to 36 V supply range provides broad operating flexibility. The external pull-up may reference a different logic supply from the comparator, enabling level translation without a dedicated translator IC. For noisy or slow-changing signals, positive feedback can add hysteresis and suppress repeated transitions. Confirm that the input common-mode voltage and differential voltage remain within the limits published in the LM2903W datasheet.

🧩

Low-Power Monitoring and Control

The LM2903WHYST fits low-power monitoring systems that require local threshold decisions without a continuously operating digital controller. Its 0.4 mA typical supply current is independent of the supply voltage, and each comparator consumes approximately 1 mW at 5 V according to the manufacturer documentation. Two channels can supervise local conditions and wake or inhibit downstream circuitry through open-collector pull-ups. The device can also implement a simple window comparator using two reference inputs and externally wired outputs. For low-duty-cycle systems, validate the quiescent current over the full expected supply range and ensure that pull-up resistors do not dominate the standby power budget.

What is the operating voltage of LM2903WHYST?
The LM2903WHYST operates from 2 V to 36 V on a single supply or from ±1 V to ±18 V in dual-supply configurations. According to the STMicroelectronics LM2903W datasheet, the wide range supports low-voltage battery systems and higher industrial supply rails. The device contains two independent comparators, and each channel can be evaluated against its own input pair.
What are the key specifications of LM2903WHYST that engineers should know?
The LM2903WHYST is a dual, low-power, open-collector voltage comparator with a 2 V to 36 V single-supply range. Manufacturer documentation specifies 0.4 mA typical supply current independent of supply voltage, 25 nA typical input bias current, ±5 nA typical input offset current, and 250 mV typical output saturation at 4 mA. It is supplied in an 8-MiniSO surface-mount package.
Where to download the LM2903WHYST datasheet PDF?
The official LM2903W datasheet PDF is available from STMicroelectronics at https://www.st.com/resource/en/datasheet/lm2903w.pdf. It contains the electrical characteristics, comparator block diagram, pin configuration, application information, and package details for the LM2903WH family. The corresponding LM2903WH product page is also linked in the product documentation section.
Where can I find the LM2903WHYST pinout?
The LM2903WHYST uses an 8-MiniSO package with two independent comparator channels. Its functional connections are IN− on pins 2 and 6, IN+ on pins 3 and 5, OUT on pins 1 and 7, VCC on pin 8, and GND on pin 4. Use the pin-description table in the STMicroelectronics LM2903W datasheet when assigning PCB tracks.
Is LM2903WHYST suitable for battery-powered applications?
Yes, the LM2903WHYST is suitable for battery-powered applications because its typical supply current is 0.4 mA and remains independent of supply voltage. The manufacturer lists approximately 1 mW consumption per comparator at 5 V. Its common-mode input range includes the negative rail, which is useful in single-cell sensing systems.
What is the output type of LM2903WHYST?
The LM2903WHYST has open-collector outputs on pins 1 and 7. An external pull-up resistor is therefore required to establish a high output level. The STMicroelectronics LM2903W datasheet identifies a typical low saturation voltage of 250 mV at 4 mA, and the open-collector outputs can also be combined in a wired-AND arrangement.
Can LM2903WHYST be used as a Schmitt trigger?
Yes, the LM2903WHYST can be used as a Schmitt trigger by applying positive feedback to one input of a comparator channel. This creates hysteresis and prevents output chatter when the sensed signal crosses the threshold slowly. The feedback network must preserve the common-mode and differential input limits stated in the manufacturer datasheet.
What pull-up resistor should be used with LM2903WHYST?
The LM2903WHYST pull-up resistor should be chosen from the logic supply and the required switching speed rather than from a fixed universal value. A larger resistance reduces sink current but slows the rising edge, while a smaller resistance gives faster edges and consumes more current during the low output state. The 250 mV typical saturation specification at 4 mA provides a useful starting point for the maximum sink current.
What can replace LM2903WHYST?
A true replacement for LM2903WHYST must use the same 8-MiniSO footprint, preserve the pin arrangement, and meet the relevant supply, common-mode, offset, and output specifications. Same-family LM2903WH options may provide engineering alternatives when their exact suffix, temperature grade, and package match. Confirm the ordering code and pin configuration in the manufacturer datasheet before production use.
Is LM2903WHYST the same as LM2903DT?
The LM2903WHYST and LM2903DT belong to the same low-power dual-comparator family, but they are not automatically interchangeable because their packages differ. LM2903WHYST is specified in 8-MiniSO, while LM2903DT is listed in 8-SOIC. A different package footprint requires PCB adaptation and therefore is not a strict drop-in replacement.
What is the best Texas Instruments equivalent for LM2903WHYST?
The closest Texas Instruments family equivalent is LM2903, but it must be matched to the exact package and ordering suffix before it can replace LM2903WHYST on an existing board. TI describes LM2903 as pin-for-pin compatible with the compared device in its product documentation. However, an 8-SOIC or 8-MSOP option is not a direct 8-MiniSO drop-in without a footprint change.
When should I choose LM2903WHYST over another dual comparator?
Choose LM2903WHYST when the design needs two independent low-power comparator channels, operation across a 2 V to 36 V supply range, and open-collector outputs in the compact 8-MiniSO package. It is particularly useful for battery-powered threshold detection where low supply current and negative-rail common-mode coverage matter. Select another family member only when a required grade, output style, or exact footprint differs.
Where to buy LM2903WHYST online?
The LM2903WHYST can be ordered through XAIPART's Request a Quote form on this page. The form is the preferred route for checking current availability, order quantity, and delivery timing for the exact 8-MiniSO ordering code. Confirm the requested package, temperature grade, and reel configuration when submitting the request.
What is the price of LM2903WHYST?
The current commercial terms for LM2903WHYST are generated through XAIPART's Request a Quote form on this page. Use that form for the exact MPN and required quantity so the quote reflects current sourcing conditions and the correct 8-MiniSO package. Static prices are not embedded in this product description because they can change during normal procurement.
What is the lead time and stock status for LM2903WHYST?
Current stock and lead time for LM2903WHYST should be confirmed through XAIPART's Request a Quote form on this page. Include the required quantity, packaging method, and target delivery date in the request. The manufacturer lists LM2903WHYST for direct ordering through STMicroelectronics, but project-specific availability can change with order configuration.

داده‌های مرجع مهندسی برای LM2903WHYST — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose LM2903WHYST when the design requires two independent low-power comparator channels in an 8-MiniSO footprint and can operate from 2 V to 36 V. It is especially useful for battery-powered threshold detection, ground-referenced sensing, and open-collector digital interfacing. Select LM2903VQDRG4Q1 when an automotive Q1 family option is required, provided its exact ordering and qualification details match the system requirements. LM2903DT can be considered for same-family standardization when its package, grade, and sourcing configuration satisfy the PCB and qualification constraints. LM2903M offers a Texas Instruments sourcing alternative with the same basic dual open-collector topology, while LM2903DQ provides a 3PEAK alternative for low-power systems that include ground in the common-mode range. For any substitution, verify the exact land pattern, pin numbering, common-mode limits, output sink current, temperature grade, and open-collector pull-up requirements rather than relying only on the comparator type.

مقایسه با جایگزین‌ها

پارامتر این محصول LM2903WH LM2903VQDRG4Q1 LM2903DT LM2903M LM2903DQ
Package 8-MiniSO 8-MiniSO 8-MiniSO 8-MiniSO 8-MiniSO 8-MiniSO
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics Texas Instruments 3PEAK
Comparator Channels 2 independent comparators 2 independent comparators 2 independent comparators 2 independent comparators 2 independent comparators 2 independent comparators
Output Architecture Open-collector Open-collector Open-collector Open-collector Open-collector Open-collector

تفاوت‌های کلیدی

  • Wide single-supply operating range (در مقابلLM2903DQ)
  • Very low supply current independent of supply voltage (در مقابلLM2903M)
  • Low input bias and offset currents (در مقابلLM2903DT)
  • Negative-rail-inclusive common-mode input range (در مقابلLM2903DQ)
  • Automotive-focused family option (در مقابلLM2903WH)

یادداشت‌های طراحی

Do not treat the open-collector output as a push-pull logic output. Install an external pull-up resistor on each comparator output and connect it to the voltage required by the receiving device. If both outputs are tied together, size the shared pull-up for the maximum combined sink current and ensure that the resulting rise time meets the receiving circuit's timing requirements.

Estimated: the LM2903WHYST supply-current dissipation at 5 V is approximately 0.4 mA × 5 V = 2 mW for the complete dual device, consistent with the manufacturer's 1 mW per comparator figure. Add pull-up-resistor current and any connected logic load when calculating total power. This estimate does not include dynamic output-transition or external-reference current.

Route the two comparator channels to keep sensitive input traces away from switching nodes, motor phases, inductors, and high-current return paths. Use a continuous ground reference beneath the inputs and place the output pull-up resistor close to the comparator pin or receiving input. High-impedance divider nodes should have minimal copper area to reduce leakage and noise pickup.

For slowly changing or noisy inputs, add controlled positive feedback to create Schmitt-trigger hysteresis. Calculate the hysteresis from the resistor network while confirming that both inputs remain inside the common-mode range under all supply conditions. Also ensure that source impedance is low enough that input bias current and offset current do not materially shift the switching threshold.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The manufacturer documentation describes ECOPACK options by environmental grade, but a specific compliance declaration for the LM2903WHYST ordering code could not be established from the cited product information.

جستجوهای مرتبط

LM2903WHYST datasheet LM2903WHYST pinout LM2903WHYST datasheet pdf LM2903WHYST equivalent LM2903WHYST replacement LM2903WHYST cross reference LM2903WHYST vs LM2903DT LM2903WHYST footprint LM2903WHYST price LM2903WHYST stock STMicroelectronics LM2903WHYST LM2903WHYST open collector output

قطعات و اصطلاحات مرتبط

STMicroelectronics LM2903WHYST LM2903WH LM2903VQDRG4Q1 LM2903DT LM2903M LM2903DQ voltage comparator dual comparator analog integrated circuit amplifier IC open-collector output open-drain interface single-supply operation dual-supply operation input bias current input offset current common-mode voltage output saturation voltage 8-MiniSO surface mount TTL CMOS industrial sensor interface battery monitoring
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ