LM2904LVIDR - 1MHz Dual Low-Voltage Op Amp | Texas Instruments
料号: LM2904LVIDR ✓ 量产中LM2904LVIDR 概述
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The LM2904LVIDR contains two amplifiers in one package, making it useful for dual-channel signal chains, buffer stages, transducers, and low-voltage control systems. Its family position is operational amplifier -> voltage-feedback amplifier -> analog amplifier -> integrated circuit.
The device is specified for dual operation at a 5.5 V maximum supply. Texas Instruments describes the LM2904LV as a dual, 5.5 V, 1 MHz operational amplifier with a 3 mV offset-voltage rating. The 8-SOIC package supports conventional surface-mount assembly, while the dual configuration reduces board area for applications that need two amplifier channels.
The LM2904LVIDR is intended for instrumentation and general-purpose analog designs where a low-voltage supply is important. Typical uses include sensor-interface amplification, audio signal conditioning, process-control loops, and buffering of low-level analog signals. The 1 MHz bandwidth is suitable for moderate-frequency rather than high-speed precision applications, and the 3 mV input offset specification should be considered in sensor and instrumentation designs requiring low input-level accuracy.
For stable operation, follow the manufacturer's recommended supply, common-mode input, output-voltage, and decoupling guidelines from the LM2904LV datasheet. Place the supply bypass capacitor close to the device and keep sensitive input routing short to reduce noise pickup. The two amplifier channels in the package are independent, but each requires correct biasing and appropriate output-load conditions.
This product summary combines the LM2904LV family specifications with practical guidance for PCB layout, application selection, and replacement planning. It is designed to help engineers identify whether the 8-SOIC dual op amp meets the voltage, bandwidth, offset, and package requirements of a new analog design.
直接替换替代料: LM2904LVIDR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2904LVIDR (相同外形与封装尺寸) ——差异在于 Input Offset Voltage, Number of Channels, Package.
LM2904LVIDR 最大额定值与电气特性
| Product Type | Dual operational amplifier |
| Amplifier Architecture | Voltage-feedback amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Offset Voltage | 3 mV |
| 封装 | 8-SOIC |
| 引脚数 | 8 pins |
| 安装类型 | Surface mount |
| Product Family | LM2904LV |
LM2904LVIDR 8-soic 引脚配置指南
LM2904LVIDR(8-soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM2904LVIDR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM2904LVIDR 适用于 6 应用s: Low-Voltage Sensor Signal Conditioning, Audio Preamplifier and Buffer, Industrial Process-Control Loops, Data-Acquisition Front End, Portable Measurement Equipment, Power-Supply Feedback and Monitoring.
Low-Voltage Sensor Signal Conditioning
The LM2904LVIDR fits dual-channel sensor conditioning when the system operates near a 5 V rail. Its 1 MHz gain-bandwidth product provides useful bandwidth for moderate-frequency sensor signals, while the two channels can amplify or buffer complementary outputs without adding a second package. The 3 mV input offset rating must be compared with the sensor output and required accuracy. Keep input traces short, locate input resistors close to the amplifier pins, and confirm that the sensor's common-mode voltage remains within the LM2904LV operating limits.
推荐
Audio Preamplifier and Buffer
The LM2904LVIDR can provide two general-purpose audio preamplifier or buffer stages in a compact 8-SOIC footprint. The 1 MHz bandwidth is appropriate for conventional audio-band signal paths, and the low-voltage LM2904LV family is useful in portable or low-voltage equipment. Output swing, input common-mode range, and load capability should be verified from the manufacturer data before fixing the gain and output network. Use short, shielded signal routes and maintain good ground-return paths to minimize hum and channel coupling.
推荐
Industrial Process-Control Loops
The LM2904LVIDR is suitable for low-voltage industrial process-control circuits that need two generic amplifier channels. It can support error amplifiers, current-loop interfaces, actuator feedback stages, or signal comparators within the LM2904LV common-mode and output-range limits. The 1 MHz bandwidth is more than adequate for many slow control loops, while the 3 mV offset value must be included in the loop-error budget. Provide local supply bypassing and route high-impedance input nodes away from switching nodes and power inductors.
推荐
Data-Acquisition Front End
The LM2904LVIDR can form the input stage of a low-voltage data-acquisition front end when the source bandwidth is moderate. Its dual-channel arrangement allows differential or dual-ended signal conditioning, and the 1 MHz bandwidth accommodates many externally sampled industrial signals. Input offset, bias current, noise, common-mode range, and settling behavior must be checked against the acquisition resolution and source impedance. Use a guarded input layout, a stable reference architecture, and short paths from sensor or converter outputs.
推荐
Portable Measurement Equipment
The LM2904LVIDR supports portable measurement equipment powered from a low-voltage system because the LM2904LV family is specified with a 5.5 V maximum supply. The two channels can serve as sensor amplifiers, output drivers, or buffered references within the device's output-swing capability. Low-voltage headroom does not guarantee operation at every input level, so verify common-mode voltage before adding gain. Power-consumption budgeting, input bias current, and board leakage can be important when the source is a high-impedance sensor.
推荐
Power-Supply Feedback and Monitoring
The LM2904LVIDR can implement low-voltage output-feedback, difference, or monitoring amplifiers around a regulated power rail. Its 1 MHz bandwidth provides margin for feedback-loop and transient requirements in many low-voltage designs, but the exact loop stability must be evaluated with the output network. The 3 mV offset becomes more significant on small feedback-divider differences, so resistor matching and input-bias effects should be included in the error budget. Keep feedback traces away from switching power stages and use a quiet ground reference.
推荐
推荐产品汇总
工程参考数据: LM2904LVIDR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2904DR |
|---|---|---|
| Package | 8-SOIC | 8-SOIC |
| Brand | Texas Instruments | Texas Instruments |
| Number of Amplifier Channels | 2 | 2 |
| Product Family | LM2904LV | LM2904 |
| Primary Use Case | Low-voltage general-purpose dual amplifier | General-purpose dual amplifier |
| Pin Compatibility | 8-SOIC dual-op-amp footprint | Pin-to-pin compatible in 8-SOIC |
关键差异点
- Purpose-built low-voltage family characteristics (对比 LM2904DR)
- Defined bandwidth for low-voltage analog designs (对比 LM2904DR)
- Two channels in one compact package (对比 LM2904DR)
设计说明
Assign the amplifier pins using the LM2904LV manufacturer's pin-description table for the 8-SOIC package. Place input and output components close to their associated pins, keep high-impedance input traces short, and route them away from switching nodes. Maintain a continuous ground reference beneath the analog section where practical, because the two channels share the same package and ground structure.
Use a supply within the LM2904LV operating range and include local bypass capacitance close to the power pins. The exact capacitor value and stability requirements should follow the manufacturer datasheet and the gain configuration used. Check output swing under the intended load because a 5.5 V maximum supply rating does not imply full rail-to-rail output behavior.
Include the 3 mV input offset rating in the accuracy budget for low-level sensor and feedback applications. Input bias current, source impedance, resistor tolerance, and output loading can contribute additional error. For small-signal stages, favor a grounded or well-defined return path and avoid long parallel traces that increase capacitive pickup and channel-to-channel coupling.
合规信息
Compliance status requires confirmation from the manufacturer's current product documentation or material declaration.