Texas Instruments

LM2904LVIDR - 1MHz Dual Low-Voltage Op Amp | Texas Instruments

MPN: LM2904LVIDR ✓ פעיל
5.5 V Vdss 8-SOIC Package
כמות הזמנה מינימלית: 1 |

LM2904LVIDR סקירה

The Texas Instruments LM2904LVIDR is a dual, low-voltage, general-purpose operational amplifier with a 5.5 V maximum supply rating, 1 MHz gain-bandwidth product, and 3 mV input offset voltage. It is supplied in an 8-pin SOIC package and is designed for cost-sensitive signal-conditioning and analog-instrumentation applications.

An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The LM2904LVIDR contains two amplifiers in one package, making it useful for dual-channel signal chains, buffer stages, transducers, and low-voltage control systems. Its family position is operational amplifier -> voltage-feedback amplifier -> analog amplifier -> integrated circuit.

The device is specified for dual operation at a 5.5 V maximum supply. Texas Instruments describes the LM2904LV as a dual, 5.5 V, 1 MHz operational amplifier with a 3 mV offset-voltage rating. The 8-SOIC package supports conventional surface-mount assembly, while the dual configuration reduces board area for applications that need two amplifier channels.

The LM2904LVIDR is intended for instrumentation and general-purpose analog designs where a low-voltage supply is important. Typical uses include sensor-interface amplification, audio signal conditioning, process-control loops, and buffering of low-level analog signals. The 1 MHz bandwidth is suitable for moderate-frequency rather than high-speed precision applications, and the 3 mV input offset specification should be considered in sensor and instrumentation designs requiring low input-level accuracy.

For stable operation, follow the manufacturer's recommended supply, common-mode input, output-voltage, and decoupling guidelines from the LM2904LV datasheet. Place the supply bypass capacitor close to the device and keep sensitive input routing short to reduce noise pickup. The two amplifier channels in the package are independent, but each requires correct biasing and appropriate output-load conditions.

This product summary combines the LM2904LV family specifications with practical guidance for PCB layout, application selection, and replacement planning. It is designed to help engineers identify whether the 8-SOIC dual op amp meets the voltage, bandwidth, offset, and package requirements of a new analog design.

חלופות תחליף ישיר עבור LM2904LVIDR — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם LM2904LVIDR (אותו גורם צורה וטביעת רגל) — שונים ב Input Offset Voltage, Number of Channels, Package.

Texas Instruments
Input Offset Voltage: 2 mV (typical)
Number of Channels: 2
Package: 8-SOIC (D)
השווה עם LM2904LVIDR →

LM2904DR

✅ Drop-In
Texas Instruments
📦 8-SOIC
2 · 3 V to 26 V · ±1.5 V to ±13 V · 700 kHz · 0.3 V/us · 2 mV (typical) · 500 uA (typical) · 0.7 mA (typical)

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

LM2904LVIDR דירוגים מרביים ומאפיינים חשמליים

Product Type Dual operational amplifier
Amplifier Architecture Voltage-feedback amplifier
Number of Channels 2 channels
Maximum Supply Voltage 5.5 V
Gain-Bandwidth Product 1 MHz
Input Offset Voltage 3 mV
מארז 8-SOIC
מספר פינים 8 pins
סוג הרכבה Surface mount
Product Family LM2904LV

מדריך תצורת פינים של LM2904LVIDR 8-soic

תצורת פינים עבור LM2904LVIDR (מארזת 8-soic). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.

תרשים פינים של מארזת 8-soic עבור LM2904LVIDR

אין נתוני פריסת פינים מפורטים עבור LM2904LVIDR.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

LM2904LVIDR מתאים עבור 6 יישוםs: Low-Voltage Sensor Signal Conditioning, Audio Preamplifier and Buffer, Industrial Process-Control Loops, Data-Acquisition Front End, Portable Measurement Equipment, Power-Supply Feedback and Monitoring.

🧩

Low-Voltage Sensor Signal Conditioning

The LM2904LVIDR fits dual-channel sensor conditioning when the system operates near a 5 V rail. Its 1 MHz gain-bandwidth product provides useful bandwidth for moderate-frequency sensor signals, while the two channels can amplify or buffer complementary outputs without adding a second package. The 3 mV input offset rating must be compared with the sensor output and required accuracy. Keep input traces short, locate input resistors close to the amplifier pins, and confirm that the sensor's common-mode voltage remains within the LM2904LV operating limits.

🎧

Audio Preamplifier and Buffer

The LM2904LVIDR can provide two general-purpose audio preamplifier or buffer stages in a compact 8-SOIC footprint. The 1 MHz bandwidth is appropriate for conventional audio-band signal paths, and the low-voltage LM2904LV family is useful in portable or low-voltage equipment. Output swing, input common-mode range, and load capability should be verified from the manufacturer data before fixing the gain and output network. Use short, shielded signal routes and maintain good ground-return paths to minimize hum and channel coupling.

🏭

Industrial Process-Control Loops

The LM2904LVIDR is suitable for low-voltage industrial process-control circuits that need two generic amplifier channels. It can support error amplifiers, current-loop interfaces, actuator feedback stages, or signal comparators within the LM2904LV common-mode and output-range limits. The 1 MHz bandwidth is more than adequate for many slow control loops, while the 3 mV offset value must be included in the loop-error budget. Provide local supply bypassing and route high-impedance input nodes away from switching nodes and power inductors.

📺

Data-Acquisition Front End

The LM2904LVIDR can form the input stage of a low-voltage data-acquisition front end when the source bandwidth is moderate. Its dual-channel arrangement allows differential or dual-ended signal conditioning, and the 1 MHz bandwidth accommodates many externally sampled industrial signals. Input offset, bias current, noise, common-mode range, and settling behavior must be checked against the acquisition resolution and source impedance. Use a guarded input layout, a stable reference architecture, and short paths from sensor or converter outputs.

📱

Portable Measurement Equipment

The LM2904LVIDR supports portable measurement equipment powered from a low-voltage system because the LM2904LV family is specified with a 5.5 V maximum supply. The two channels can serve as sensor amplifiers, output drivers, or buffered references within the device's output-swing capability. Low-voltage headroom does not guarantee operation at every input level, so verify common-mode voltage before adding gain. Power-consumption budgeting, input bias current, and board leakage can be important when the source is a high-impedance sensor.

⚡

Power-Supply Feedback and Monitoring

The LM2904LVIDR can implement low-voltage output-feedback, difference, or monitoring amplifiers around a regulated power rail. Its 1 MHz bandwidth provides margin for feedback-loop and transient requirements in many low-voltage designs, but the exact loop stability must be evaluated with the output network. The 3 mV offset becomes more significant on small feedback-divider differences, so resistor matching and input-bias effects should be included in the error budget. Keep feedback traces away from switching power stages and use a quiet ground reference.

What are the key specifications of LM2904LVIDR that engineers should know?
The LM2904LVIDR is a dual, 5.5 V, 1 MHz operational amplifier with a 3 mV input-offset-voltage rating in an 8-SOIC package. According to the Texas Instruments LM2904LV product information, the device belongs to the LM2904LV low-voltage family and provides two general-purpose amplifier channels. These specifications make it appropriate for low-voltage signal conditioning, buffering, and instrumentation circuits, while the 1 MHz bandwidth and 3 mV offset rating should be checked against the accuracy and frequency requirements of the target application.
What is the operating voltage of LM2904LVIDR?
The LM2904LVIDR is specified for operation from a low-voltage supply with a 5.5 V maximum supply rating. The Texas Instruments LM2904LV product page identifies the part as a dual, 5.5 V operational amplifier, while the detailed minimum and nominal supply values are listed in the LM2904LV datasheet. Confirm the complete input-voltage range, input common-mode limits, and output-swing limits against that datasheet before using the amplifier with a particular supply rail.
How many amplifiers are in LM2904LVIDR and what package does it use?
The LM2904LVIDR contains two independent operational-amplifier channels in an 8-SOIC package. The DigiKey listing identifies it as a standard general-purpose, 2-circuit, 8-SOIC amplifier, and Texas Instruments identifies LM2904LV as a dual operational-amplifier family member. The dual configuration is useful when a design needs two signal paths, while the 8-SOIC package allows use of conventional surface-mount PCB assembly.
Where can I download the LM2904LVIDR datasheet PDF?
The manufacturer datasheet and product information are available from the Texas Instruments LM2904LV product page at https://www.ti.com/product/LM2904LV. The same manufacturer page provides ordering information, parameters, and support resources for the LM2904LV family. Use the pin-description table and electrical-characteristics tables in that document when assigning PCB connections and verifying the 5.5 V maximum supply, 1 MHz bandwidth, and 3 mV offset specifications.
Where can I find the LM2904LVIDR pinout?
The LM2904LVIDR pinout is identified in the manufacturer's LM2904LV datasheet and package information for the 8-SOIC configuration. Texas Instruments lists the LM2904LV family at https://www.ti.com/product/LM2904LV, and the DigiKey product page identifies the exact LM2904LVIDR orderable part as an 8-SOIC dual amplifier. Assign amplifier inputs, outputs, supply rails, and bypass pins by following the pin-description table for the specific package rather than assuming that every dual op amp uses the same numbering.
What is the gain-bandwidth product of LM2904LVIDR?
The LM2904LVIDR has a 1 MHz gain-bandwidth product. Texas Instruments describes LM2904LV as a dual, 5.5 V, 1 MHz operational amplifier family member, and the Mouser listing likewise identifies the exact part as a 1 MHz dual amplifier. This bandwidth is appropriate for general-purpose audio, buffering, sensor-interface, and process-control stages operating at moderate frequencies. Higher-frequency designs should verify the complete closed-loop response, slew rate, and stability requirements in the datasheet.
What is the input offset voltage of LM2904LVIDR?
The LM2904LVIDR is rated with a 3 mV input offset voltage. The Texas Instruments LM2904LV product page specifies the LM2904LV family as a dual, 5.5 V, 1 MHz operational amplifier with a 3 mV offset-voltage rating, and Mouser lists the same 3 mV value for LM2904LVIDR. Input offset matters most when the source impedance and signal amplitude are low enough that the offset can dominate the measurement or cause an unacceptable output error.
Is LM2904LVIDR suitable for low-voltage sensor interfaces?
The LM2904LVIDR is suitable for many low-voltage sensor-interface circuits because it combines a 5.5 V maximum supply with a 1 MHz gain-bandwidth product and two amplifier channels. Its 3 mV input offset rating must be weighed against the sensor's full-scale output and required accuracy. Place input components close to the device, use the pin description table for correct channel assignment, and confirm input common-mode voltage and output-swing limits against the LM2904LV datasheet.
Where can I buy LM2904LVIDR and how do I request a quote?
The LM2904LVIDR can be requested through the Request a Quote form on this page. The part is a Texas Instruments dual operational amplifier in an 8-SOIC package, and the manufacturer product page provides authoritative ordering and technical information. Use the quote form to confirm current unit availability, quantity breaks, lead time, and shipment requirements rather than relying on a static listing price that may change.
What is the price of LM2904LVIDR?
The current commercial price for LM2904LVIDR should be confirmed through the Request a Quote form on this page. The part is a Texas Instruments 8-SOIC dual operational amplifier, and availability and pricing can vary with order quantity, packaging, and inventory status. Submit the required quantity and delivery information through the quote form to obtain a current response.
What is the lead time for LM2904LVIDR?
The current lead time for LM2904LVIDR should be confirmed through the Request a Quote form on this page. Texas Instruments lists the LM2904LV family as an active product family, but an exact lead time depends on the requested quantity, scheduled delivery date, and the manufacturing and distribution status at the time of inquiry. Provide the required quantity and target date when requesting a quotation.
Is LM2904LVIDR in stock?
LM2904LVIDR inventory status should be confirmed through the Request a Quote form on this page. The manufacturer identifies the LM2904LV family as a supported product family, while distributor listings can change as stock is allocated. Request a quotation with the required quantity and shipping destination to receive the current availability and delivery plan.
What can replace LM2904LVIDR on the same PCB?
The LM2904DR is a documented pin-to-pin functional replacement candidate for LM2904LVIDR because both are dual general-purpose op amps in 8-SOIC packages. The replacement differs because LM2904LVIDR provides the enhanced low-voltage family characteristics, including a 5.5 V maximum supply and 1 MHz bandwidth, while LM2904DR belongs to the higher-voltage LM2904 family. Confirm every electrical limit, common-mode range, output swing, and AEC-Q100 requirement before substituting it in production.
When should I choose LM2904LVIDR instead of LM2904DR?
Choose LM2904LVIDR when the design operates from a low-voltage rail and benefits from the LM2904LV family's 5.5 V maximum supply and 1 MHz bandwidth. Choose LM2904DR only when its higher-voltage operating envelope is needed and its complete electrical characteristics remain acceptable. Both use an 8-SOIC dual-op-amp footprint, but low-voltage operation, supply headroom, input range, output swing, and qualification requirements should drive the final choice.
LM2904LVIDR vs LM2904DR: which is better for a 5 V design?
The LM2904LVIDR is generally the better match for a nominal 5 V design because it belongs to the LM2904LV low-voltage family and is specified for 5.5 V maximum supply operation. The LM2904DR is the pin-to-pin 8-SOIC alternative documented for replacement, but it belongs to the original LM2904 family. The choice should still be confirmed against the exact supply, input common-mode range, output swing, offset, bandwidth, and application qualification requirements.
What is the best Texas Instruments equivalent for LM2904LVIDR?
The best documented Texas Instruments pin-compatible equivalent identified for LM2904LVIDR is the LM2904DR, which is described as a functionally compatible, pin-to-pin replacement in an 8-SOIC package. The principal distinction is the low-voltage family behavior of LM2904LVIDR versus the original LM2904 family used by LM2904DR. Verify that the replacement supports the design's actual supply voltage, input signal range, output swing, bandwidth, and environmental requirements.

נתוני עזר הנדסיים עבור LM2904LVIDR — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose LM2904LVIDR when the circuit needs two general-purpose amplifier channels, operates from a low-voltage rail, and requires the documented LM2904LV characteristics of a 5.5 V maximum supply, 1 MHz gain-bandwidth product, and 3 mV input offset rating. It is well matched to sensor conditioning, audio buffering, process-control loops, and general data-acquisition front ends. LM2904DR is the documented pin-to-pin 8-SOIC replacement candidate when the original LM2904 family's electrical envelope is preferable or required. Confirm the alternative's supply voltage, common-mode range, output swing, bandwidth, offset, and environmental qualification before approving a substitution. Neither choice should be selected solely by package name: a correct footprint does not guarantee that all operating limits remain acceptable.

השוואה עם חלופות

פרמטר מוצר זה LM2904DR
Package 8-SOIC 8-SOIC
Brand Texas Instruments Texas Instruments
Number of Amplifier Channels 2 2
Product Family LM2904LV LM2904
Primary Use Case Low-voltage general-purpose dual amplifier General-purpose dual amplifier
Pin Compatibility 8-SOIC dual-op-amp footprint Pin-to-pin compatible in 8-SOIC

מבדילים עיקריים

  • Purpose-built low-voltage family characteristics (לעומתLM2904DR)
  • Defined bandwidth for low-voltage analog designs (לעומתLM2904DR)
  • Two channels in one compact package (לעומתLM2904DR)

הערות תכנון

Assign the amplifier pins using the LM2904LV manufacturer's pin-description table for the 8-SOIC package. Place input and output components close to their associated pins, keep high-impedance input traces short, and route them away from switching nodes. Maintain a continuous ground reference beneath the analog section where practical, because the two channels share the same package and ground structure.

Use a supply within the LM2904LV operating range and include local bypass capacitance close to the power pins. The exact capacitor value and stability requirements should follow the manufacturer datasheet and the gain configuration used. Check output swing under the intended load because a 5.5 V maximum supply rating does not imply full rail-to-rail output behavior.

Include the 3 mV input offset rating in the accuracy budget for low-level sensor and feedback applications. Input bias current, source impedance, resistor tolerance, and output loading can contribute additional error. For small-signal stages, favor a grounded or well-defined return path and avoid long parallel traces that increase capacitive pickup and channel-to-channel coupling.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

Compliance status requires confirmation from the manufacturer's current product documentation or material declaration.

הנתונים אומתו בתאריך: 2026-11-17 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

LM2904LVIDR LM2904LVIDR datasheet LM2904LVIDR datasheet pdf LM2904LVIDR pinout LM2904LVIDR equivalent LM2904LVIDR replacement LM2904LVIDR vs LM2904DR Texas Instruments LM2904LVIDR LM2904LV 5.5V dual op amp LM2904LVIDR 8-SOIC amplifier LM2904LVIDR sensor signal conditioning LM2904LVIDR price

רכיבים ומונחים קשורים

Texas Instruments LM2904LVIDR LM2904LV LM2904DR operational amplifier dual operational amplifier voltage-feedback amplifier analog amplifier integrated circuit signal conditioning sensor interface input offset voltage gain-bandwidth product low-dropout power architecture 5.5 V maximum supply 1 MHz bandwidth 3 mV offset voltage 8-SOIC SOIC family surface-mount package RoHS REACH AEC-Q100
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר