LM2904NG - Dual Op Amp, 1MHz, 3-26V, PDIP-8 | onsemi
料号: LM2904NG ✓ 量产中LM2904NG 概述
An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output that, together with resistors or capacitors in a feedback network, implements amplification, filtering, comparison, buffering and mathematical functions. The op amp sits at the core of the analog signal-chain hierarchy: amplifier IC -> analog front end -> mixed-signal system. The LM2904 family is the industry-standard dual op amp lineage originally popularized by National Semiconductor and carried forward by multiple manufacturers, including onsemi and Texas Instruments.
Key features include a common-mode input voltage range that extends to ground/VEE, enabling the device to sense signals near 0V in single-supply systems, low power drain, and internal frequency compensation that eliminates external compensation components. Single-supply or split-supply operation gives designers flexibility across battery-powered and industrial 24V-class rails. The through-hole PDIP package suits prototyping, repair, education and legacy industrial boards.
Architecturally, the LM2904NG uses circuit designs perfected for quad operational amplifiers, packaged as two channels sharing one bias network. Internally compensated pole-splitting keeps the device unity-gain stable without external capacitors, while the class-AB output stage sources and sinks modest load currents. Care is required when sinking current near ground with a single supply, since the output sinks through the ground return path and low-side saturation behavior limits accuracy near 0V on the output swing.
Typical applications include transducer amplifiers and sensor front ends, DC gain blocks and active filters, and conventional op amp circuits in industrial control, automotive-adjacent electronics and instrumentation where the -40C to +105C ambient range and ground-sensing inputs are required.
Design consideration: in single-supply configurations, bias inputs above the input common-mode floor and avoid driving the output into deep saturation, because recovery from output saturation introduces overshoot and gain errors; decouple the supply pin with 0.1uF close to pin 8.
This page synthesizes distributor availability, drop-in alternatives and practical design guidance not found in the manufacturer datasheet, giving engineers a single decision-ready reference.
直接替换替代料: LM2904NG ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2904NG (相同外形与封装尺寸) ——差异在于 Package, Mounting Type, Slew Rate, Amplifier Type, Input Bias Current.
LM2904N
✅ 直接替换联系询价
查看数据手册 →LM2904BIDR
✅ 直接替换联系询价
查看数据手册 →LM2904-N
✅ 直接替换📋 参考替代料(不在目录中)
LM2904NG 最大额定值与电气特性
| Amplifier Type | General Purpose |
| Number of Circuits | 2 |
| Gain Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/µs |
| Supply Voltage Range | 3 V to 26 V |
| 工作温度 | -40C to +105C |
| 封装 / 外壳 | PDIP-8 (0.300 in, 7.62 mm) |
| 安装类型 | Through Hole |
| Packaging | Tube |
| Input Common-Mode Range | Extends to ground/VEE |
| Supply Type | Single supply or split supply |
| Frequency Compensation | Internal |
LM2904NG 引脚配置
| 引脚 1 | OUT1 — Output of amplifier A |
| 引脚 2 | IN1- — Inverting input of amplifier A |
| 引脚 3 | IN1+ — Non-inverting input of amplifier A |
| 引脚 4 | GND/V- — Ground or negative supply |
| 引脚 5 | IN2+ — Non-inverting input of amplifier B |
| 引脚 6 | IN2- — Inverting input of amplifier B |
| 引脚 7 | OUT2 — Output of amplifier B |
| 引脚 8 | VCC/V+ — Positive power supply |
典型应用
LM2904NG 适用于 6 应用s: Single-Supply Sensor Amplification, DC Gain Blocks and Active Filters, Comparators and Threshold Detectors, Industrial Control and Automation, Automotive-Adjacent Electronics, Audio Signal Conditioning.
Single-Supply Sensor Amplification
The LM2904NG is a natural fit for amplifying signals from transducers such as photodiodes, strain-gauge bridges, thermistors and pressure sensors that are referenced to ground in single-supply industrial systems. Its common-mode input range extending to ground/VEE allows the non-inverting input to sit at 0V without phase reversal, which many op amps cannot tolerate. With a 3V to 26V supply range, the same design scales from 5V logic-adjacent rails to industrial 24V systems. The 1 MHz gain bandwidth supports closed-loop gains of 100 or less at low frequencies with margin. For outputs that must approach 0V while sinking current, add a resistor to ground because the output sink path returns through the ground pin.
推荐
DC Gain Blocks and Active Filters
As an internally compensated, unity-gain-stable dual amplifier, the LM2904NG implements DC gain stages, Sallen-Key filters, integrators and summing amplifiers without external compensation components. In industrial control boards, setpoint scaling and 4-20 mA loop conditioning, its 1 MHz GBW covers low-pass filter corner frequencies up to tens of kilohertz with predictable phase behavior, and the 0.6 V/µs slew rate is ample for slow analog control signals. The dual channels let one package handle both the filter stage and the output scaling stage, halving board area versus single-amplifier solutions. In split-supply operation the device handles bipolar signals directly; in single-supply designs, bias the virtual ground above the input floor and avoid driving the output into saturation to prevent recovery overshoot.
推荐
Comparators and Threshold Detectors
One LM2904NG channel commonly serves as a level detector or window comparator in industrial monitoring: the open-loop stage compares a sensor-derived voltage against a resistor-divider threshold, driving a logic or LED indication. Because the input common-mode range includes ground, thresholds near 0V are detected reliably from a single supply. The -40C to +105C rating keeps detection levels stable across outdoor and cabinet-mounted equipment temperatures. A design consideration is that the LM2904 is a compensated amplifier, not a dedicated comparator, so response times are in the microsecond range and the output does not provide clean open-collector logic; add hysteresis with positive feedback and follow with a transistor stage when driving relays or logic inputs, or use a dedicated comparator family for sub-microsecond response.
推荐
Industrial Control and Automation
Factory automation, motor control supervision and PLC analog I/O modules routinely embed the LM2904 family because it tolerates 24V-class supply environments (26V maximum), survives -40C to +105C ambient and is second-sourced industry-wide, simplifying long-term procurement. Typical roles include transducer signal conditioning ahead of an ADC, current-sense amplification across shunt resistors, and buffer stages between DAC outputs and actuator drive circuits. Its low power drain matters in densely packed I/O cards. Designers should decouple the supply pin with 0.1uF close to pin 8, route ground returns away from high-current motor drive paths to protect the ground-sensing input accuracy, and exploit the dual channels to separate noisy and clean halves of the analog front end.
推荐
Automotive-Adjacent Electronics
The LM2904 family was originally specified for automotive-grade environments, and the -40C to +105C range of the LM2904NG covers under-hood-adjacent modules, body electronics and instrument clusters where cold crank and elevated cabin temperatures occur. Its single-supply ground-sensing inputs condition signals from potentiometer position sensors, coolant temperature dividers and battery-voltage monitors, while the 26V rating absorbs load-dump-adjacent transients when paired with upstream protection. Through-hole PDIP packaging suits serviceable automotive test fixtures and legacy modules. For genuinely AEC-Q100-qualified new designs, verify the specific variant's qualification level in the onsemi product documentation, since packaging suffixes determine qualification; the electrical core, however, has decades of proven automotive field history across the industry-standard LM2904 lineage.
推荐
Audio Signal Conditioning
The LM2904NG serves in low-fidelity and utility audio paths: microphone preamplifiers for intercoms, line-level summing, active tone controls and audio level detection in industrial PA and security systems. Its 1 MHz GBW supports closed-loop gains up to roughly 100 across most of the audio band, and the 0.6 V/µs slew rate handles full-amplitude audio up to the upper tens of kilohertz without gross slew distortion. Operation from a single supply simplifies intercom and alarm-panel power design, with the input biased at mid-supply through a divider. The device is not intended for high-end audio - its noise and distortion figures exceed those of dedicated audio op amps - so for hi-fi signal paths substitute a low-noise audio dual amplifier, but for robust utility audio the LM2904NG's supply tolerance and temperature range are decisive.
推荐
推荐产品汇总
工程参考数据: LM2904NG ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2904N | LM2904B | LM2904-N | LM2904VN | LM358NG |
|---|---|---|---|---|---|---|
| Package | PDIP-8 (0.300 in, 7.62 mm) | PDIP-8 (0.300 in, 7.62 mm) - same | PDIP-8 (0.300 in, 7.62 mm) - same | PDIP-8 (0.300 in, 7.62 mm) - same | PDIP-8 (0.300 in, 7.62 mm) - same | PDIP-8 (0.300 in, 7.62 mm) - same |
| Brand | onsemi | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | onsemi |
| Number of Circuits | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage Range | 3 V to 26 V | 3 V to 26 V class | 3 V to 26 V class | 3 V to 26 V class | 3 V to 26 V class | 3 V to 32 V class |
| Operating Temperature | -40C to +105C | -40C to +105C class | -40C to +125C class | -40C to +105C class | -40C to +105C class | 0C to +70C/+85C class |
| Temperature Grade Distinction | Industrial (LM2904 prefix) | Industrial (LM2904 prefix) | Industrial enhanced (LM2904B) | Industrial (LM2904 prefix) | Industrial/extended V grade | Commercial (LM358 prefix) |
| Mounting Type | Through Hole | Through Hole | Through Hole (PDIP option) | Through Hole | Through Hole | Through Hole |
关键差异点
- Industrial temperature grade for harsh environments (对比 LM358NG)
- Industry-standard pinout with broadest second sourcing (对比 LM2904B)
- Ground-sensing inputs in single-supply designs (对比 LM2904N)
设计说明
Do not assume the LM2904NG output swings to 0V under load. The output sinks current through the ground pin, so a low-side load (for example an LED or resistor returned to ground) holds the output tens to hundreds of millivolts above ground. If a stage must produce a true 0V output, return the sinking load to a small negative rail or add a pull-down resistor so the amplifier sources rather than sinks. Also avoid input voltages more than one diode drop below V-; although the input common-mode range includes ground, excessive negative differential input can cause phase inversion of the output.
Decouple the VCC pin (pin 8) with a 0.1uF ceramic capacitor placed within a few millimeters of the pin, particularly in single-supply 24V industrial environments where supply transients from relays and switching loads propagate on shared rails. Keep the input traces (pins 2, 3, 5, 6) short and guard high-impedance nodes with ground pour to limit leakage and pickup. Because this is a through-hole PDIP part, use an IC socket for serviceable industrial assemblies, but note that socket contact resistance adds negligible error only for closed-loop gains where feedback resistor values exceed roughly 10 kohm.
Respect the small-signal and large-signal limits separately: with a 1 MHz gain bandwidth product, a closed-loop gain of 100 yields only about 10 kHz of bandwidth, and the 0.6 V/µs slew rate limits a 10V-peak sine to roughly 19 kHz before slew distortion appears. Estimate the required slew rate as 2*pi*f*Vpeak and verify it stays below 0.6 V/µs. For filter designs, keep the closed-loop bandwidth at least 20x above the filter corner frequency so phase shift of the amplifier itself does not alter the transfer function. These are standard first-order estimates; confirm with simulation for precision designs.
合规信息
Compliance status should be confirmed on the onsemi official product page for the LM2904NG suffix before design-in.