LM293ST - Dual 2V-36V Comparator | STMicroelectronics
料号: LM293ST ✓ 量产中LM293ST 概述
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM293 family belongs to the comparator and amplifier IC category within the broader semiconductor hierarchy. Its open-collector outputs can sink current while remaining in a high-impedance state, making the device suitable for wired logic, pull-up resistor networks, relay drivers, and systems that require a flexible output drive configuration.
The LM293ST provides two independent comparators, low offset, and high precision according to the STMicroelectronics LM293 family information. Its rail-to-rail input operation allows each differential input to approach the supply rails, which is useful when monitoring low-voltage sensor signals or battery-powered thresholds. The open-collector outputs also provide a deliberate isolation between the comparator output and the supply voltage, permitting external pull-up selection for a different logic family.
Both channels can operate from a single 2 V to 36 V supply, and the device also supports split power-supply arrangements. The low-power architecture is intended for general-purpose threshold detection rather than high-speed signal conditioning. Because the outputs are open collector, designers must add pull-up resistors when a continuously driven high level is required. The output transistor provides current sinking capability, while the external pull-up establishes the high-state voltage and limits the available rise rate.
Typical applications include industrial sensor thresholding, overvoltage and undervoltage detection, battery monitoring, window-comparator circuits, control-loop signaling, and digital interface adaptation. Two channels can also implement a hysteretic switching controller, an automatic window detector, or a pair of independent limit alarms. In each case, input and output implementation details should be checked against the operating voltage, common-mode range, load current, and logic requirements of the completed circuit.
The principal design consideration is that an open-collector output is not a push-pull logic output. Select the pull-up resistor and logic voltage carefully, keep the pull-up current within the output sink-current rating, and place the device close enough to the protected signal path to minimize pickup of switching noise. The exposed package also requires attention to copper area and thermal conditions when either channel operates continuously at maximum load.
This product page brings together the manufacturer family information, distributor listing attributes, package details, replacement guidance, and practical design considerations. It also distinguishes verified electrical attributes from parameters that require confirmation from the LM293 manufacturer datasheet, helping engineers plan a replacement or design-in without relying on package-code assumptions.
直接替换替代料: LM293ST ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM293ST (相同外形与封装尺寸) ——差异在于 Comparator Type, Output Type, Package.
LM293ST 最大额定值与电气特性
| Comparator Type | Dual differential voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V |
| 输出类型 | Open-collector, open-drain |
| Input Common-Mode Range | Rail-to-rail |
| 封装 | 8-pin MiniSO |
| 安装类型 | Surface mount |
| Single-Supply Operation | Supported |
| Split-Supply Operation | Supported |
LM293ST 引脚配置
| 引脚 1 | OUT1 — Comparator 1 open-collector output |
| 引脚 2 | IN1- — Comparator 1 inverting input |
| 引脚 3 | IN1+ — Comparator 1 non-inverting input |
| 引脚 4 | GND — Ground connection |
| 引脚 5 | IN2+ — Comparator 2 non-inverting input |
| 引脚 6 | IN2- — Comparator 2 inverting input |
| 引脚 7 | OUT2 — Comparator 2 open-collector output |
| 引脚 8 | VCC — Positive supply connection |
典型应用
LM293ST 适用于 6 应用s: Industrial Sensor Threshold Detection, Battery Overvoltage and Undervoltage Protection, Automatic Window Comparator, Relay and Solenoid Interface, Digital Logic Level Translation, Motor and Fan Limit Monitoring.
Industrial Sensor Threshold Detection
The LM293ST is suitable for monitoring a sensor signal against an adjustable reference because it provides two independent differential comparator channels and rail-to-rail inputs. One channel can compare a conditioned transducer output with a precision reference, while the other can supervise a second limit. The open-collector output can drive a relay, optocoupler input, or PLC input through a pull-up network. Because the comparator operates from 2 V to 36 V, it supports both low-energy sensor circuits and industrial supply buses. The principal design checks are input offset accuracy, input bias current, response time, and the pull-up current required by the downstream load.
推荐
Battery Overvoltage and Undervoltage Protection
The two channels in the LM293ST can implement independent battery upper and lower threshold alarms. A divided battery voltage is compared against references, and each open-collector output can pull down a system fault line when its corresponding limit is exceeded. The device’s 2 V to 36 V supply range allows it to operate from many battery-derived rails, while rail-to-rail inputs help cover signals that occupy much of the available voltage range. In a protection circuit, include hysteresis to prevent repeated switching near the threshold, and size the pull-up resistor for the required fault-line current. Input offset and divider tolerance should be calculated together when setting protection limits.
推荐
Automatic Window Comparator
A dual comparator can implement an automatic window detector by assigning one LM293ST channel to the lower limit and the other to the upper limit. The sensed voltage is compared with two references, and the open-collector outputs can be combined through wired logic so the system reports an in-range state only when neither limit is active. This arrangement is useful for battery packs, regulated rails, and industrial process variables that must remain between defined boundaries. Add positive feedback for hysteresis and verify that the input common-mode range covers the minimum and maximum sensed voltages. The pull-up network must also preserve the required active-high or active-low fault polarity.
推荐
Relay and Solenoid Interface
The open-collector output of the LM293ST can sink current into a transistor or relay-driver stage when a control signal crosses a threshold. This isolates the sensitive comparator input from the inductive load while allowing the 2 V to 36 V device to operate across a broad range of control voltages. The output must include a pull-up resistor because it cannot source a driven high level by itself. For relay and solenoid circuits, add a suitable flyback path at the load, observe the driver transistor’s voltage and current ratings, and keep the comparator supply stable. The two channels can control two loads independently or combine their outputs when a shared interlock is required.
推荐
Digital Logic Level Translation
The LM293ST can compare a low-voltage digital or analog signal against a threshold and produce an open-collector signal referenced to a separately selected logic rail. A pull-up resistor connected to the destination logic supply allows the output to interoperate with a voltage family other than the comparator supply. This arrangement is useful for adapting fault signals between systems operating at different logic voltages. The conversion is suitable for static or low-rate signals rather than high-speed data buses. Designers must ensure that every input remains within the common-mode limits, that the pull-up voltage is permitted, and that the sink current stays below the output rating. Hysteresis may be necessary when noisy signals cross the decision threshold repeatedly.
推荐
Motor and Fan Limit Monitoring
The LM293ST can monitor a motor-drive supply, current-sense signal, or auxiliary feedback voltage against a reference and generate an open-collector fault indication. Its 2 V to 36 V operating range accommodates a broad class of industrial and appliance control circuits, while two channels support independent speed, voltage, or thermal-enable supervision. A pull-up resistor allows the fault output to interface with a microcontroller, gate-driver enable, or status LED. For motor environments, keep comparator traces away from high-current switching paths and provide stable reference and supply bypassing. The input network should account for offset, propagation delay, and noise so a transient does not create an unintended shutdown indication.
推荐
推荐产品汇总
工程参考数据: LM293ST ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM393ST |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | 8-pin MiniSO | 8-pin MiniSO |
| Comparator Channels | 2 channels | 2 channels |
| Output Type | Open-collector, open-drain | Open-collector, open-drain |
关键差异点
- Exact-package same-family replacement path (对比 LM393ST)
- Wide single-supply operating range (对比 LM393ST)
- Dual rail-to-rail sensing (对比 LM393ST)
设计说明
Place the LM293ST close to the reference network and the two compared input signals to reduce susceptibility to coupled noise. Keep the comparator ground connection on a low-impedance return path, and place the open-collector pull-up resistor close to the output pin. If a ground pad is not shown for this MiniSO package, verify the land pattern and pin numbering against the manufacturer drawing before fabrication.
Do not treat an open-collector output as a push-pull output. Without a pull-up resistor, the output can sink current but cannot establish a valid high level. Select the pull-up voltage for compatibility with the receiving circuit, calculate its sink current at the maximum low-level voltage, and include the resistor’s static power dissipation in the design. Also avoid using the output pin as a general-purpose power source.
Add positive feedback or controlled hysteresis when the compared signals can cross the threshold slowly or exhibit noise. Hysteresis prevents output chatter around the decision point, but the selected gap must remain smaller than the minimum meaningful signal separation. For high-impedance sensors, account for input bias current and source impedance because they can create an offset at the comparator inputs.
合规信息
No explicit compliance declarations were included in the manufacturer or distributor product information for this ordering code. The AEC-Q100 field is not applicable because the LM293ST is presented as a general-purpose industrial comparator rather than an automotive-qualified variant.