STMicroelectronics

LM293ST - Dual 2V-36V Comparator | STMicroelectronics

MPN: LM293ST ✓ Active
2 V to 36 V Vdss 8-pin MiniSO Package
MOQ: 1 |

LM293ST Overview

The STMicroelectronics LM293ST is a dual differential voltage comparator designed for low-voltage operation, with a 2 V to 36 V supply range and open-collector, open-drain outputs. The device contains two independent comparator channels in an 8-pin MiniSO surface-mount package, allowing both channels to operate from the same supply or from split power rails.

A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM293 family belongs to the comparator and amplifier IC category within the broader semiconductor hierarchy. Its open-collector outputs can sink current while remaining in a high-impedance state, making the device suitable for wired logic, pull-up resistor networks, relay drivers, and systems that require a flexible output drive configuration.

The LM293ST provides two independent comparators, low offset, and high precision according to the STMicroelectronics LM293 family information. Its rail-to-rail input operation allows each differential input to approach the supply rails, which is useful when monitoring low-voltage sensor signals or battery-powered thresholds. The open-collector outputs also provide a deliberate isolation between the comparator output and the supply voltage, permitting external pull-up selection for a different logic family.

Both channels can operate from a single 2 V to 36 V supply, and the device also supports split power-supply arrangements. The low-power architecture is intended for general-purpose threshold detection rather than high-speed signal conditioning. Because the outputs are open collector, designers must add pull-up resistors when a continuously driven high level is required. The output transistor provides current sinking capability, while the external pull-up establishes the high-state voltage and limits the available rise rate.

Typical applications include industrial sensor thresholding, overvoltage and undervoltage detection, battery monitoring, window-comparator circuits, control-loop signaling, and digital interface adaptation. Two channels can also implement a hysteretic switching controller, an automatic window detector, or a pair of independent limit alarms. In each case, input and output implementation details should be checked against the operating voltage, common-mode range, load current, and logic requirements of the completed circuit.

The principal design consideration is that an open-collector output is not a push-pull logic output. Select the pull-up resistor and logic voltage carefully, keep the pull-up current within the output sink-current rating, and place the device close enough to the protected signal path to minimize pickup of switching noise. The exposed package also requires attention to copper area and thermal conditions when either channel operates continuously at maximum load.

This product page brings together the manufacturer family information, distributor listing attributes, package details, replacement guidance, and practical design considerations. It also distinguishes verified electrical attributes from parameters that require confirmation from the LM293 manufacturer datasheet, helping engineers plan a replacement or design-in without relying on package-code assumptions.

Drop-in alternatives for LM293ST — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with LM293ST (same form factor and footprint) — differing in Comparator Type, Output Type, Package.

STMicroelectronics
Comparator Type: Dual general-purpose voltage comparator
Output Type: Open-collector
Package: 8-MiniSO
Compare with LM293ST →

LM393ST

✅ Drop-In
STMicroelectronics
📦 8-pin MiniSO
Dual general-purpose voltage comparator · 2 channels · Open-collector · Rail-to-rail · 2 V to 36 V · 36 V · 8-MiniSO · 8 pins

Contact for price

View Datasheet →

LM293ST Maximum Ratings & Electrical Characteristics

Comparator Type Dual differential voltage comparator
Number of Channels 2 channels
Supply Voltage Range 2 V to 36 V
Output Type Open-collector, open-drain
Input Common-Mode Range Rail-to-rail
Package 8-pin MiniSO
Mounting Type Surface mount
Single-Supply Operation Supported
Split-Supply Operation Supported

LM293ST Pin Configuration

MSOP-8 Package Pinout Diagram MSOP-8 3x3mm, P0.65mm, JEDEC MO-187. 1 8 2 7 3 6 4 5 MSOP-8
Pin 1 OUT1 — Comparator 1 open-collector output
Pin 2 IN1- — Comparator 1 inverting input
Pin 3 IN1+ — Comparator 1 non-inverting input
Pin 4 GND — Ground connection
Pin 5 IN2+ — Comparator 2 non-inverting input
Pin 6 IN2- — Comparator 2 inverting input
Pin 7 OUT2 — Comparator 2 open-collector output
Pin 8 VCC — Positive supply connection

Typical Applications

LM293ST is suitable for 6 applications: Industrial Sensor Threshold Detection, Battery Overvoltage and Undervoltage Protection, Automatic Window Comparator, Relay and Solenoid Interface, Digital Logic Level Translation, Motor and Fan Limit Monitoring.

🏭

Industrial Sensor Threshold Detection

The LM293ST is suitable for monitoring a sensor signal against an adjustable reference because it provides two independent differential comparator channels and rail-to-rail inputs. One channel can compare a conditioned transducer output with a precision reference, while the other can supervise a second limit. The open-collector output can drive a relay, optocoupler input, or PLC input through a pull-up network. Because the comparator operates from 2 V to 36 V, it supports both low-energy sensor circuits and industrial supply buses. The principal design checks are input offset accuracy, input bias current, response time, and the pull-up current required by the downstream load.

⚡

Battery Overvoltage and Undervoltage Protection

The two channels in the LM293ST can implement independent battery upper and lower threshold alarms. A divided battery voltage is compared against references, and each open-collector output can pull down a system fault line when its corresponding limit is exceeded. The device’s 2 V to 36 V supply range allows it to operate from many battery-derived rails, while rail-to-rail inputs help cover signals that occupy much of the available voltage range. In a protection circuit, include hysteresis to prevent repeated switching near the threshold, and size the pull-up resistor for the required fault-line current. Input offset and divider tolerance should be calculated together when setting protection limits.

🔋

Automatic Window Comparator

A dual comparator can implement an automatic window detector by assigning one LM293ST channel to the lower limit and the other to the upper limit. The sensed voltage is compared with two references, and the open-collector outputs can be combined through wired logic so the system reports an in-range state only when neither limit is active. This arrangement is useful for battery packs, regulated rails, and industrial process variables that must remain between defined boundaries. Add positive feedback for hysteresis and verify that the input common-mode range covers the minimum and maximum sensed voltages. The pull-up network must also preserve the required active-high or active-low fault polarity.

🔧

Relay and Solenoid Interface

The open-collector output of the LM293ST can sink current into a transistor or relay-driver stage when a control signal crosses a threshold. This isolates the sensitive comparator input from the inductive load while allowing the 2 V to 36 V device to operate across a broad range of control voltages. The output must include a pull-up resistor because it cannot source a driven high level by itself. For relay and solenoid circuits, add a suitable flyback path at the load, observe the driver transistor’s voltage and current ratings, and keep the comparator supply stable. The two channels can control two loads independently or combine their outputs when a shared interlock is required.

🖥️

Digital Logic Level Translation

The LM293ST can compare a low-voltage digital or analog signal against a threshold and produce an open-collector signal referenced to a separately selected logic rail. A pull-up resistor connected to the destination logic supply allows the output to interoperate with a voltage family other than the comparator supply. This arrangement is useful for adapting fault signals between systems operating at different logic voltages. The conversion is suitable for static or low-rate signals rather than high-speed data buses. Designers must ensure that every input remains within the common-mode limits, that the pull-up voltage is permitted, and that the sink current stays below the output rating. Hysteresis may be necessary when noisy signals cross the decision threshold repeatedly.

🔧

Motor and Fan Limit Monitoring

The LM293ST can monitor a motor-drive supply, current-sense signal, or auxiliary feedback voltage against a reference and generate an open-collector fault indication. Its 2 V to 36 V operating range accommodates a broad class of industrial and appliance control circuits, while two channels support independent speed, voltage, or thermal-enable supervision. A pull-up resistor allows the fault output to interface with a microcontroller, gate-driver enable, or status LED. For motor environments, keep comparator traces away from high-current switching paths and provide stable reference and supply bypassing. The input network should account for offset, propagation delay, and noise so a transient does not create an unintended shutdown indication.

What is the operating voltage of LM293ST?
The LM293ST operates from a 2 V to 36 V supply and contains two independent comparator channels. According to the STMicroelectronics LM293 family page, the devices are intended for operation from a single supply over a wide voltage range and can also operate from split power supplies. Each channel must remain within the detailed absolute-maximum and common-mode limits stated in the manufacturer datasheet.
Where can I download the LM293ST datasheet PDF?
The official LM293 family documentation is available on the STMicroelectronics product page at https://www.st.com/en/amplifiers-and-comparators/lm293.html. From that page, select the LM293 documentation and download the datasheet PDF. The LM293ST ordering suffix identifies the 8-pin MiniSO package, so use the ordering-information table to confirm the package drawing, pinout, and electrical limits for that suffix.
Where can I find the LM293ST pinout?
The LM293ST pinout is defined by the 8-pin MiniSO ordering information in the STMicroelectronics LM293 datasheet. The standard dual-comparator arrangement uses pins 1 and 7 for OUT1 and OUT2, pins 2 and 6 for IN1− and IN2−, pins 3 and 5 for IN1+ and IN2+, pin 4 for GND, and pin 8 for VCC. Confirm the diagram before assigning PCB nets.
What are the key specifications of LM293ST?
The LM293ST is a dual, low-power differential comparator with a 2 V to 36 V supply range, rail-to-rail inputs, and open-collector, open-drain outputs. The device provides two independent channels and supports both single and split power-supply configurations, according to the STMicroelectronics LM293 family description. Its 8-pin MiniSO package supports compact surface-mount designs.
Is the LM293ST open collector or push-pull?
The LM293ST uses open-collector, open-drain outputs rather than push-pull outputs. Its output transistor actively sinks current but does not source a high-level current, so a pull-up resistor is normally required. The pull-up voltage defines the logic-high level and should be selected to remain compatible with the driven device and the LM293ST operating conditions.
Can LM293ST use split power supplies?
Yes, the LM293ST can operate from split power supplies because the two comparator channels are independent and support dual-supply configurations. Each channel compares its non-inverting and inverting inputs, while the output transistor references the lower supply rail. Check the manufacturer datasheet for common-mode input and supply-current limits before assigning bipolar voltage ranges.
What can replace the LM293ST?
The LM393ST is the closest documented drop-in candidate for the LM293ST because it is offered by STMicroelectronics in the same 8-pin MiniSO package and implements the same dual open-collector comparator architecture. Compatibility still depends on the required offset, input bias current, response time, common-mode limits, temperature range, and output-current ratings, which should be compared against the LM293 datasheet.
Is LM293ST the same as LM393ST?
The LM293ST and LM393ST use the same 8-pin MiniSO format and both contain two independent open-collector comparators, but they are not necessarily identical in every electrical or temperature-grade specification. The STMicroelectronics family page groups the LM293 and LM393 devices together, while detailed replacement decisions require comparing offset voltage, response time, supply current, and operating-temperature limits in the manufacturer datasheets.
What is the best Texas Instruments equivalent for LM293ST?
The Texas Instruments LM293 is functionally similar because it is a dual differential comparator with an industrial-grade product description. A direct substitution also requires matching the 8-pin MiniSO footprint and open-collector output configuration; the TI LM293 page does not establish that the ordering code shown in the LM293ST listing is available in the identical package. Verify the TI ordering suffix and pin assignment before treating it as a drop-in replacement.
When should I choose LM293ST over LM393ST?
Choose the LM293ST when the design specifies its offset, precision, temperature, and electrical performance and requires the exact STMicroelectronics 8-pin MiniSO implementation. Choose LM393ST when its documented ratings satisfy the application and a second source is useful within the same package and topology. The meaningful distinction is device-level performance and qualification, not the number of channels or output style.
LM293ST vs LM393ST: which is better for industrial sensing?
The better choice depends on the specific industrial sensing conditions rather than on general-purpose functionality alone. Both devices provide two open-collector comparator channels in the same 8-pin MiniSO format and can monitor rail-to-rail input conditions. Compare the manufacturer-specified offset voltage, input bias current, response time, temperature range, and noise behavior against the sensor accuracy and production-temperature requirements.
How do I use the LM293ST open-drain output?
Connect an external pull-up resistor from the comparator output to the required logic-high rail, normally the positive supply in a single-supply circuit. The output transistor sinks current when the inverting input is higher than the non-inverting input; otherwise the output remains high impedance and the pull-up establishes a high level. Select the resistor to balance sink current, power consumption, rise time, and downstream input-current requirements.
Where to buy LM293ST online?
Use the Request a Quote form on this page to request LM293ST pricing, stock confirmation, and lead time for the exact 8-pin MiniSO ordering code. Quote requests prevent a package or suffix mismatch and let procurement confirm current channel availability. The form is the appropriate route for commercial terms because market pricing and inventory can change by quantity and date.
What is the price of LM293ST?
Current LM293ST pricing is obtained through the Request a Quote form on this page. The form accepts the required quantity and packaging information so procurement can confirm a quote for the exact LM293ST ordering code. A request should specify the 8-pin MiniSO package and the number of units needed rather than relying on a generic dual-comparator price.
What is the lead time and stock status for LM293ST?
The current lead time and stock status for LM293ST should be confirmed through the Request a Quote form on this page. Procurement can validate the exact package suffix, order quantity, scheduled delivery, and available channel inventory at the time of quotation. These commercial terms can change without notice and should be recorded together with the purchase order.

Engineering reference data for LM293ST — comparison, design guidance, and compliance information.

Selection Guide

Choose the LM293ST when the design requires an STMicroelectronics dual comparator in the 8-pin MiniSO package, particularly for 2 V to 36 V single-supply operation, rail-to-rail input sensing, or split-supply designs. Select the LM393ST when it is a qualified same-package alternative and its offset, bias current, response time, supply current, and temperature limits better satisfy the application. The open-collector outputs on both devices require external pull-up resistors, so that interface remains unchanged when moving between the two. A Texas Instruments LM293 may offer a second functional source, but it must not be treated as a footprint-compatible substitute unless its exact ordering suffix is confirmed as 8-pin MiniSO and its pin functions match. For every choice, verify the input common-mode limits at the lowest and highest signal values, check output sink current against the pull-up load, and validate behavior across the required temperature range.

Comparison with Alternatives

Parameter This Product LM393ST
Brand STMicroelectronics STMicroelectronics
Package 8-pin MiniSO 8-pin MiniSO
Comparator Channels 2 channels 2 channels
Output Type Open-collector, open-drain Open-collector, open-drain

Key Differentiators

  • Exact-package same-family replacement path (vs LM393ST)
  • Wide single-supply operating range (vs LM393ST)
  • Dual rail-to-rail sensing (vs LM393ST)

Design Notes

Place the LM293ST close to the reference network and the two compared input signals to reduce susceptibility to coupled noise. Keep the comparator ground connection on a low-impedance return path, and place the open-collector pull-up resistor close to the output pin. If a ground pad is not shown for this MiniSO package, verify the land pattern and pin numbering against the manufacturer drawing before fabrication.

Do not treat an open-collector output as a push-pull output. Without a pull-up resistor, the output can sink current but cannot establish a valid high level. Select the pull-up voltage for compatibility with the receiving circuit, calculate its sink current at the maximum low-level voltage, and include the resistor’s static power dissipation in the design. Also avoid using the output pin as a general-purpose power source.

Add positive feedback or controlled hysteresis when the compared signals can cross the threshold slowly or exhibit noise. Hysteresis prevents output chatter around the decision point, but the selected gap must remain smaller than the minimum meaningful signal separation. For high-impedance sensors, account for input bias current and source impedance because they can create an offset at the comparator inputs.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

No explicit compliance declarations were included in the manufacturer or distributor product information for this ordering code. The AEC-Q100 field is not applicable because the LM293ST is presented as a general-purpose industrial comparator rather than an automotive-qualified variant.

Data verified on: 2026-11-10 — data verified and curated by XAIPART's component engineering team

Related Searches

LM293ST datasheet LM293ST datasheet pdf LM293ST pinout LM293ST specifications LM293ST 8 pin MiniSO STMicroelectronics LM293ST LM293ST 2V 36V comparator LM293ST equivalent LM293ST replacement LM293ST vs LM393ST LM293ST open collector output LM293ST price LM293ST buy online LM293ST industrial sensor application

Related Components & Terms

STMicroelectronics LM293ST LM293 LM393ST Texas Instruments LM293 dual differential comparator voltage comparator comparator IC amplifier IC integrated circuit semiconductor open-collector output open-drain output rail-to-rail input split power supply 2 V to 36 V supply voltage input offset voltage input bias current response time 8-pin MiniSO MiniSO package surface-mount package industrial sensor threshold detection battery protection
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details