LM339AMX - Quad Low-Offset Voltage Comparator SOIC-14 | Texas Instruments
料号: LM339AMX ✓ 量产中LM339AMX 概述
A differential comparator is a mixed-signal building block that compares two input voltages and drives its output to indicate which is higher. Comparators sit within the broader amplifier and analog IC hierarchy, alongside operational amplifiers, but are optimized for fast switching and saturated logic-level outputs rather than linear operation. Because the LM339A family includes ground in its common-mode range, it can sense signals near zero volts on a single rail.
Key features include four independent comparators in one package, wide single-supply operation from 2 V to 36 V (or ±18 V dual), low typical supply current drain of about 800 uA, and outputs compatible with TTL, DTL, MOS, and CMOS logic. The open-collector output stage allows wired-OR connections and level shifting to arbitrary logic voltages via a pull-up resistor. Low input offset voltage and operation with the input common-mode range including ground make the device suitable for near-ground sensing.
Technically, the open-collector output transistors saturate at a low voltage, giving clean logic-level transitions and easy interfacing. A typical response time of approximately 1.3 us suits threshold detection, level translation, and oscillator circuits rather than ultra-high-speed applications.
Typical applications include limit comparators, simple analog-to-digital converters, pulse generators, square-wave and relaxation oscillators, window detectors, and voltage monitoring in industrial and consumer systems.
For design, remember that every output requires an external pull-up resistor since the output stage is open-collector, and inputs must be kept within the common-mode range even beyond the supply voltage specified in the absolute maximum ratings for differential input.
This page adds value beyond the manufacturer datasheet by synthesizing distributor sourcing information, drop-in alternatives, comparison tables, and practical design notes in one place.
直接替换替代料: LM339AMX ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM339AMX (相同外形与封装尺寸) ——差异在于 Package, Output Type, Comparator Type, Logic Compatibility, Number of Comparators.
LM339AMX/NOPB
✅ 直接替换联系询价
查看数据手册 →LM339DR
✅ 直接替换✓ 有现货
$0.0738 / 个
查看数据手册 →LM339ADR2
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM339M/NOPB
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM339AMX/NOPB
✅ 直接替换联系询价
查看数据手册 →LM339AMX 最大额定值与电气特性
| 功能 | Quad differential comparator |
| Number of Comparators | 4 |
| 输出类型 | Open-Collector (DTL, TTL, MOS, CMOS compatible) |
| Supply Voltage Range (Single) | 2 V to 36 V |
| Supply Voltage Range (Dual) | ±1 V to ±18 V |
| Supply Current (Typical) | 800 uA |
| Common-Mode Input Voltage Range | Includes ground |
| Response Time (Typical) | 1.3 us |
| Output Saturation Voltage | Low output saturation voltage (per TI product page) |
| 封装 | 14-SOIC (0.154 in, 3.90 mm width) |
| 工作温度范围 | 0 C to 70 C |
| 安装类型 | Surface Mount |
| Packaging | Tape & Reel (T/R) |
| Series | LM339A (A version) |
LM339AMX 引脚配置
| 引脚 1 | OUT2 — Output of comparator 2 (open-collector, requires pull-up) |
| 引脚 2 | OUT1 — Output of comparator 1 (open-collector, requires pull-up) |
| 引脚 3 | VCC — Positive supply, 2 V to 36 V (or ±1 V to ±18 V dual) |
| 引脚 4 | IN1- — Inverting input of comparator 1 |
| 引脚 5 | IN1+ — Non-inverting input of comparator 1 |
| 引脚 6 | IN2- — Inverting input of comparator 2 |
| 引脚 7 | IN2+ — Non-inverting input of comparator 2 |
| 引脚 8 | IN3- — Inverting input of comparator 3 |
| 引脚 9 | IN3+ — Non-inverting input of comparator 3 |
| 引脚 10 | IN4- — Inverting input of comparator 4 |
| 引脚 11 | IN4+ — Non-inverting input of comparator 4 |
| 引脚 12 | GND — Ground / negative supply |
| 引脚 13 | OUT4 — Output of comparator 4 (open-collector, requires pull-up) |
| 引脚 14 | OUT3 — Output of comparator 3 (open-collector, requires pull-up) |
典型应用
LM339AMX 适用于 6 应用s: Limit Comparators and Window Detectors, Battery and Supply Voltage Monitoring, Relaxation Oscillators and Pulse Generators, Simple Analog-to-Digital Converters, Sensor Threshold Detection in Industrial Control, Level Shifting and Logic Interfacing.
Limit Comparators and Window Detectors
The LM339AMX is a classic choice for limit comparators and window detector circuits that flag whether a voltage is inside or outside a defined band. Its common-mode input range includes ground, so it senses near-zero signals directly on a single 5 V or 12 V rail without level shifting, and the 2 V to 36 V supply range covers automotive-style 12 V and industrial 24 V monitoring rails. Two of the four comparators form a standard window detector: one flags above the upper reference, the other below the lower reference, and their open-collector outputs wire-OR into a single fault line through one pull-up resistor. The low output saturation voltage keeps the fault logic level clean for TTL or CMOS inputs, and the 1.3 us typical response time is far faster than the slow-moving thresholds typical of supply supervision.
推荐
Battery and Supply Voltage Monitoring
Battery undervoltage alarms and supply supervision circuits benefit directly from the LM339AMX. With a typical supply current drain of only about 800 uA across a 2 V to 36 V range, the device adds minimal load to a battery being monitored, and it remains in specification down to 2 V, close to the discharge floor of single-cell and lead-acid systems. A resistor divider scales the battery voltage into the comparator input while a TL431 or zener-derived reference sets the threshold; the open-collector output drives an LED or a microcontroller interrupt line through a pull-up. The A-grade offset specification of the LM339AMX tightens the guaranteed trip-point accuracy compared with standard LM339 versions, which matters when the alarm threshold must not drift over the commercial 0 C to 70 C range.
推荐
Relaxation Oscillators and Pulse Generators
The LM339AMX builds reliable relaxation oscillators, square-wave generators, and pulse generators using one comparator, a timing capacitor, and a resistor network with hysteresis. Because the output is open-collector with a low saturation voltage, the square-wave output swings cleanly to the pull-up rail and interfaces to TTL, MOS, or CMOS timing chains without a level shifter. The typical 1.3 us response time limits the practical upper frequency to roughly the low hundreds of kilohertz, which is ideal for clock sources, LED flashers, tone generators, and switched-capacitor clocking in industrial and consumer products. Operating from a single 5 V to 15 V rail with ground-sensing inputs simplifies single-supply design, and the remaining three comparators in the package can implement threshold detection or a second oscillator channel at no extra package cost.
推荐
Simple Analog-to-Digital Converters
Flash-type and integrating analog-to-digital converters built from discrete parts use banks of comparators, and the LM339AMX provides four open-collector comparators per package for this purpose. In a simple parallel (flash) converter, a resistor ladder generates equally spaced reference voltages and each comparator compares the input against one tap; the open-collector outputs feed a priority encoder or microcontroller GPIO port. The ground-inclusive common-mode range lets the ladder span from 0 V upward on a single supply, and the 2 V to 36 V supply range supports ladders up to 36 V for wide-dynamic-range inputs. The A-grade offset specification of the LM339AMX reduces the code-width error near each threshold compared with the standard LM339DR, improving effective resolution in low-bit-count converters.
推荐
Sensor Threshold Detection in Industrial Control
Industrial control panels use the LM339AMX to convert analog sensor outputs, such as thermistor dividers, photocells, and pressure-sensor bridges, into clean logic-level flags. Each of the four comparators monitors one sensor channel against a reference set by a potentiometer or TL431, so a single SOIC-14 package supervises four independent trip points with minimal board area. The 2 V to 36 V single-supply range matches standard 24 V industrial logic rails, the low 800 uA supply current suits remotely powered nodes, and hysteresis added with a small positive-feedback resistor prevents chatter on slowly moving sensor signals. Open-collector outputs allow the flags to be wire-ORed onto a shared alarm line pulled up to a different logic voltage, simplifying interface to PLC inputs.
推荐
Level Shifting and Logic Interfacing
The open-collector output of the LM339AMX doubles as a simple level translator between analog domains and logic families. Because the output collector is uncommitted, the pull-up resistor can connect to 3.3 V, 5 V, or any rail up to the rated output limit, letting a comparator sensing a 24 V industrial signal deliver a clean 3.3 V logic flag to a microcontroller. Outputs are TTL, DTL, MOS, and CMOS compatible per the TI datasheet, and multiple outputs may be tied together for wired-OR fault busses. The ground-inclusive common-mode input range allows comparison of signals that swing close to 0 V, which is common when monitoring current-sense resistors referenced to ground. Adding a few millivolts of hysteresis via positive feedback gives noise immunity on resistive sensor signals.
推荐
推荐产品汇总
工程参考数据: LM339AMX ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM339AMX/NOPB | LM339DR | LM339ADR | LM339AMX (onsemi) |
|---|---|---|---|---|---|
| Package | SOIC-14 (3.90 mm) | SOIC-14 - same | SOIC-14 - same | SOIC-14 - same | SOIC-14 (14-SOP) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Number of Comparators | 4 | 4 | 4 | 4 | 4 |
| Supply Voltage (Single) | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
关键差异点
- A-grade precision at standard-family price (对比 LM339DR)
- Ground-inclusive common-mode range (对比 LM339AMX (onsemi))
- Single-package four-channel density (对比 LM393 series dual comparators)
设计说明
Every LM339AMX output is an uncommitted open-collector transistor and cannot reach a defined high level without an external pull-up resistor to a positive rail. Omitting the pull-up is the most common first-design error with this family. Choose the pull-up value by trading speed against power: 3.3 kilohm to 10 kilohm gives fast rising edges into TTL/CMOS loads, while values up to 100 kilohm reduce current in slow threshold-detection circuits. Outputs may be paralleled for wired-OR logic, but total sink current per output must stay within datasheet limits.
Add hysteresis when comparing slowly moving or noisy signals. A resistor from output to the non-inverting input, sized against the input divider impedance, creates typically 10 mV to 50 mV of hysteresis and eliminates output chatter near the threshold. Without hysteresis, the 1.3 us response time allows the output to toggle repeatedly on millivolt-level noise. Keep the HYS resistor values large enough that the added loading does not shift the divider threshold, and verify the resulting trip points at the 0 C and 70 C range limits.
Place a 100 nF ceramic decoupling capacitor directly across the VCC (pin 3) and GND (pin 12) pins of the LM339AMX, as close to the package as possible. Input divider resistors should be placed so their Thevenin impedance is low enough that input bias currents do not shift the threshold materially. Because the A version is chosen for offset precision, avoid routing high-current or switching nodes near the input traces; a ground keepout under the inputs preserves the low-offset advantage the A grade was selected for.
Estimated: at a 5 V single supply, the LM339AMX draws about 800 uA typical supply current (about 4 mW), plus pull-up current when outputs are low. With 10 kilohm pull-ups on four outputs all sinking at once, each output sinks roughly 0.5 mA, adding about 10 mW dissipated mostly in the pull-ups. Total dissipation remains far below the SOIC-14 thermal capability, so no heatsinking is required; the thermal concern in this family is negligible compared with output sink-current limits.
合规信息
The /NOPB variant denotes a lead-free (no-Pb) version; compliance details for LM339AMX specifically should be confirmed on the TI product page before release.