LM358WPT - Dual 5V 1.1MHz Op Amp | ROHM | TSSOP-8
料号: LM358WPT ✓ 量产中LM358WPT 概述
An operational amplifier, or op amp, is an analog signal-processing IC that amplifies the difference between two input voltages while providing high open-loop gain, negative feedback support, and output-voltage drive. The LM358WPT belongs to the hierarchy dual operational amplifier -> general-purpose amplifier -> analog amplifier IC -> semiconductor. Its common-mode input range can extend toward the negative supply rail, making it useful in single-supply sensor, audio, and control circuits.
The LM358WPT integrates two independent amplifiers, allowing one package to implement stereo audio channels, dual-axis sensing, active filtering, or two-stage signal conditioning. Each channel uses standard industry-style pin assignments for dual op amps: two inputs, one output, and shared positive and negative supply connections. Internal compensation removes the need for external frequency-compensation components in typical closed-loop designs.
At a nominal 5 V supply, the device combines a usable gain-bandwidth product of 1.1 MHz with a 0.3 V/us slew rate. This bandwidth supports audio-frequency and general feedback-control applications rather than high-speed signal conditioning. The large operating-supply range also permits direct interfacing with higher-voltage industrial systems, subject to the input and output common-mode limits and the device's absolute maximum ratings.
Typical uses include microphone preamplification, transducers with ground-referenced outputs, loop-control systems, transducers, and general-purpose amplification. Because the output can source and sink current within the supply limits, the part also serves as an output-buffer stage when the load is not too heavy.
When designing a PCB around the LM358WPT, place bypass capacitors close to the supply pins and route sensitive input traces away from switching nodes. Keep the negative supply connection short because common-mode performance and output swing depend on a low-impedance ground reference. Check the full operating-temperature range and load-current limits in the manufacturer datasheet before using the amplifier in extended-temperature equipment.
This page consolidates package details, supply-range information, pin assignments, drop-in replacement candidates, and application guidance into a practical engineering reference. It also organizes the main design trade-offs so that engineers can compare bandwidth, supply capability, and package reuse before committing a PCB footprint.
直接替换替代料: LM358WPT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM358WPT (相同外形与封装尺寸) ——差异在于 Amplifier Type, Package, Input Offset Voltage, Operating Temperature Range, Slew Rate.
LM358BP
✅ 直接替换联系询价
查看数据手册 →LM2904DR
✅ 直接替换联系询价
查看数据手册 →LMV358IDT
✅ 直接替换✓ 有现货
$0.13 / 个
查看数据手册 →LM358WPT 最大额定值与电气特性
| Number of Amplifiers | 2 amplifiers |
| Amplifier Type | General-purpose operational amplifier |
| Nominal Supply Voltage | 5 V |
| Single-Supply Operating Range | 3 V to 36 V |
| Split-Supply Operating Range | +/-16 V |
| Gain-Bandwidth Product | 1.1 MHz |
| Small-Signal Bandwidth | 800 kHz |
| Slew Rate | 0.3 V/us |
| 封装 | 8-pin TSSOP |
| 安装类型 | Surface mount |
| Number of Inputs | 4 differential inputs |
| 输出数量 | 2 outputs |
| Compensation | Internally compensated |
LM358WPT 引脚配置
| 引脚 1 | OUT A — Amplifier A output |
| 引脚 2 | IN A- — Amplifier A inverting input |
| 引脚 3 | IN A+ — Amplifier A non-inverting input |
| 引脚 4 | V- — Negative supply connection |
| 引脚 5 | IN B+ — Amplifier B non-inverting input |
| 引脚 6 | IN B- — Amplifier B inverting input |
| 引脚 7 | OUT B — Amplifier B output |
| 引脚 8 | V+ — Positive supply connection |
典型应用
LM358WPT 适用于 6 应用s: Single-Supply Sensor Signal Conditioning, Audio Preamplifier and Mixer, Industrial Feedback Control Loop, Active Filter and Integrator, Transducer Interface and Buffer, Power Supply and Voltage Monitoring.
Single-Supply Sensor Signal Conditioning
The LM358WPT suits ground-referenced sensors that need amplification before an ADC or controller input. Its 3 V to 36 V single-supply operating range supports both 5 V embedded systems and higher-voltage industrial interfaces, while the 1.1 MHz gain-bandwidth product provides ample bandwidth for slow sensor signals. Place the non-inverting input at the appropriate bias level, connect the feedback divider to the inverting input, and bypass pin 8 near the device. Because the exact input bias current and common-mode limits are application-critical for high-impedance sources, verify them in the manufacturer datasheet before finalizing the sensor interface.
推荐
Audio Preamplifier and Mixer
The two independent channels in the LM358WPT can handle microphone preamplification, tone shaping, or a small stereo mix stage in a 5 V system. Its 800 kHz small-signal bandwidth and 0.3 V/us slew rate cover audio-band signals without requiring external compensation. Connect each channel as a standard non-inverting or inverting amplifier and place the gain-setting resistors close to the relevant input pins. The main limitation is output-current capability: verify the load impedance and ensure the required peak level remains within the output-swing limits stated in the manufacturer datasheet.
推荐
Industrial Feedback Control Loop
The LM358WPT is appropriate for proportional, integral, or error-amplifier stages in low-bandwidth industrial control loops. Its dual-channel configuration allows one package to implement both the error amplifier and an output-buffer or auxiliary feedback channel. The 3 V to 36 V operating range accommodates a 5 V control board or a higher-voltage industrial interface, and the 1.1 MHz gain-bandwidth product is normally sufficient for slow control loops. Keep compensation components close to the amplifier, avoid grounding the V- pin through a long trace, and confirm stability using the selected noise gain and load capacitance.
推荐
Active Filter and Integrator
The LM358WPT can implement first-order active filters, integrators, and low-pass stages where the signal bandwidth remains well below its 1.1 MHz gain-bandwidth product. Both channels are internally compensated, reducing the component count compared with an uncompensated amplifier. Select resistor and capacitor values against the desired cutoff or time constant, and keep the non-inverting reference tied to a low-impedance bias point in single-supply operation. Pay particular attention to input bias-current error, input offset voltage, and output saturation when the filter has a high DC gain or long integration interval.
推荐
Transducer Interface and Buffer
A dual LM358WPT can serve as the front-end for two resistive, capacitive, or other transducer outputs referenced close to ground. The amplifier's common-mode capability toward the negative supply is useful in single-supply systems, while the wide 3 V to 36 V supply range allows the same architecture to cover higher-voltage industrial sources. Use one channel for amplification and the other for gain adjustment or output buffering. Confirm the transducer's source impedance against the input bias current, and verify that the input and output remain inside the common-mode and swing limits at the highest expected signal level.
推荐
Power Supply and Voltage Monitoring
The LM358WPT can monitor a supply rail or scaled voltage by comparing a divided input against a reference and driving a status, limit, or feedback signal. Its nominal 5 V rating and 3 V to 36 V operating range fit both low-voltage control electronics and higher-voltage supervision circuits. Use the 1.1 MHz gain-bandwidth product for slow monitoring signals rather than fast transient capture, and account for input offset when setting the switching threshold. The device also requires attention to output-state behavior during input overvoltage, so consult the absolute maximum ratings and application guidance in the manufacturer datasheet.
推荐
推荐产品汇总
工程参考数据: LM358WPT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM358B | LM2904 | LMV358 | MC1458 | NE5532 |
|---|---|---|---|---|---|---|
| Package | TSSOP-8 | TSSOP-8 | TSSOP-8 | TSSOP-8 | TSSOP-8 | TSSOP-8 |
| Brand | ROHM Semiconductor | Texas Instruments | onsemi | Texas Instruments | onsemi | Texas Instruments |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
关键差异点
- Wide single-supply operating range (对比 LMV358)
- General-purpose bandwidth for control and audio stages (对比 NE5532)
- Temperature-oriented LM358-family alternative (对比 LM2904)
- Two independent channels in one compact surface-mount package (对比 MC1458)
设计说明
The LM358WPT can operate from 3 V to 36 V, but the permissible input and output voltages are narrower than the supply range. Before connecting a higher-voltage source, verify the common-mode limits and ensure the output remains inside the output-swing window with adequate margin. Place a local bypass capacitor from pin 8 to the ground plane and connect pin 4 directly to the plane rather than routing the return through a shared conductor.
Keep the feedback resistors, input-sensing paths, and compensation components close to their associated pins. Route the two input nets as short, paired traces and keep them away from switching-regulator outputs, relay drivers, and motor power wiring. A solid ground plane under the TSSOP minimizes parasitic voltage differences, while a short V- connection helps the amplifier maintain predictable output behavior at the lower supply rail.
Do not assume that every LM358-family or dual-op-amp substitute has identical common-mode range, output swing, noise, or stability behavior. Confirm the exact ordering code, package suffix, supply rating, and pin mapping before reusing a PCB. Also avoid designing around the nominal 1.1 MHz gain-bandwidth product as though it were a guaranteed closed-loop bandwidth; the achieved value depends on noise gain, feedback values, load capacitance, and supply voltage.
For source impedances above several hundred kilohms, the input bias current and leakage current can create errors comparable to the signal being measured. Use a lower-impedance sensor or add a bias resistor at the input while checking the resulting noise-gain penalty. For audio and instrumentation channels, shield sensitive inputs, keep leakage current off the input node, and use a clean reference point for the non-inverting input.
合规信息
Compliance status has not been established from the available manufacturer and distributor records. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact ROHM ordering code before release.