LM393APWR - 38V Dual Comparator | Texas Instruments
料号: LM393APWR ✓ 量产中LM393APWR 概述
A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input becomes higher than the other. The LM393 family belongs to the comparator hierarchy within analog signal processing and power-management interfaces. Its open-collector architecture requires an external pull-up resistor, allowing the output to operate at a voltage selected by the surrounding digital circuit rather than being fixed internally by the comparator.
The precision A-grade version provides an input offset voltage of 0.37 mV, making it suitable for threshold decisions where small differential signals must be resolved accurately. Input bias current of 3.5 nA limits the voltage error created when source impedances interact with the comparator inputs. A typical supply current of 200 µA per comparator supports low-power operation, and the stated 2 kV HBM ESD rating provides useful handling robustness for industrial equipment.
Each channel contains independent differential inputs and an open-collector output. The output can pull a logic node low while the external pull-up establishes the high state, which permits wired logic, level translation, and straightforward interfacing to microcontroller input pins. Because the outputs are open collector, multiple comparator outputs can share a common pull-up when the application requires wired-AND behavior. The device is intended for operation from a single supply or from split supplies where the input common-mode range remains valid.
Typical applications include industrial sensor threshold detection, overvoltage and undervoltage protection, battery monitoring, temperature-switch interfaces, motor and relay control, and window-comparison functions in control systems. The rail-to-rail input characteristic is particularly useful in single-supply circuits where a signal may approach ground. The 8-pin TSSOP package also supports compact analog boards while exposing both comparator channels and the common supply pins.
Designers should place input resistors close to the comparator pins when the source impedance is high, because input bias current and resistor noise can create differential errors. The open-collector outputs must each have a pull-up resistor, and the chosen resistor should balance rise time, power consumption, and the sink-current capability of the output. Designers must also verify the input and output voltages against the limits of the selected supply configuration.
This page combines the core electrical characteristics, package and pinout details, practical application guidance, and qualified drop-in alternatives for engineers evaluating the LM393APWR. It also highlights the open-collector interface requirements and the key electrical differences that should be checked before replacing the part in an existing PCB design.
直接替换替代料: LM393APWR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM393APWR (相同外形与封装尺寸) ——差异在于 Package, Output Type, Maximum Supply Voltage, Comparator Type, Input Bias Current.
LM393BPWR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2903APWR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2903BPWR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2903QPWRQ1
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM393APWR 最大额定值与电气特性
| Comparator Type | Dual differential comparator |
| 输出类型 | Open collector |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 38 V |
| Common-Mode Input Range | Includes ground; rail-to-rail input |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| 电源电流 | 200 µA per comparator |
| ESD Rating | 2 kV HBM |
| Output Compatibility | TTL, MOS, and CMOS |
| Grade | Precision A grade |
| Temperature Grade | Industrial grade |
| 封装 | 8-pin TSSOP (PW) |
| 安装类型 | Surface mount |
| Differential Input Voltage Range | ±38 V maximum supply-rated range |
LM393APWR 引脚配置
| 引脚 1 | OUT 1 — Open-collector output for comparator channel 1 |
| 引脚 2 | IN 1- — Inverting input for comparator channel 1 |
| 引脚 3 | IN 1+ — Non-inverting input for comparator channel 1 |
| 引脚 4 | GND — Ground connection |
| 引脚 5 | IN 2+ — Non-inverting input for comparator channel 2 |
| 引脚 6 | IN 2- — Inverting input for comparator channel 2 |
| 引脚 7 | OUT 2 — Open-collector output for comparator channel 2 |
| 引脚 8 | VCC — Positive supply connection |
典型应用
LM393APWR 适用于 6 应用s: Industrial Sensor Threshold Detection, Battery Overvoltage and Undervoltage Protection, Temperature Switch and Fan Control, Motor and Relay Limit Detection, Window Comparator for Power Supply Monitoring, LED and Backlight Drive Control.
Industrial Sensor Threshold Detection
The LM393APWR is appropriate for monitoring a sensor signal against a reference voltage in industrial control equipment. Its 0.37 mV input offset voltage helps distinguish small threshold changes, while the common-mode input range includes ground for sensors whose output approaches 0 V. Connect the sensor and reference to one differential input pair and use the other channel for a second limit. The open-collector output can pull down a controller input through an external pull-up resistor, making the interface straightforward. Because the output is open collector, the engineer must select a pull-up value that provides adequate switching speed without excessive supply current, while also checking sensor impedance and input-bias-current error.
推荐
Battery Overvoltage and Undervoltage Protection
The LM393APWR can compare a scaled battery voltage against two reference levels to detect overvoltage or undervoltage conditions. Its low 3.5 nA input bias current minimizes the error introduced by high-value divider resistors, and the 0.37 mV offset improves threshold precision. The rail-to-rail input characteristic supports low-voltage battery systems, while the 38 V maximum supply rating covers higher-energy industrial battery packs when appropriately protected. Each open-collector output can directly pull a system enable, charger-control, or isolation-barrier input low. A pull-up resistor is required on every output, and the divider, clamp, and reference tolerances should be included in the final trip-point error calculation.
推荐
Temperature Switch and Fan Control
The LM393APWR can compare the voltage from a thermistor bridge against a precision reference to create a temperature-switch signal. Its low input offset voltage preserves accuracy when the sensing network operates close to the comparator threshold, and the common-mode range that includes ground supports simple single-supply divider arrangements. The open-collector output can drive a relay, MOSFET, or digital enable signal after adding the required pull-up resistor and, where necessary, an output driver. In fan-control designs, hysteresis is important to prevent rapid switching near the trip point; the two independent comparator channels can implement separate turn-on and turn-off thresholds or control heating and cooling outputs. Check the input network against the 3.5 nA bias current when resistor values are high.
推荐
Motor and Relay Limit Detection
The LM393APWR is useful in motor-control and relay-protection circuits where a feedback voltage must be compared with a reference. The rail-to-rail input allows the feedback signal to operate near ground, while the 38 V maximum rating supports systems with higher transient voltage when suitable protection is included. Each open-collector output can pull down a driver input, fault flag, or relay-control logic and can share a pull-up when wired-AND fault reporting is desired. The low 0.37 mV offset can improve the resolution of a finely adjusted limit. Engineers should add filtering or hysteresis to avoid nuisance trips from switching noise, and should verify that the load connected to the open-collector output stays within the comparator's sink-current and absolute-maximum limits.
推荐
Window Comparator for Power Supply Monitoring
The two channels of the LM393APWR can form a window comparator for monitoring a power rail between a lower and an upper limit. Each channel compares the scaled rail voltage with its own reference, and the two open-collector outputs can be combined to indicate whether the voltage is inside or outside the permitted window. The 3.5 nA input bias current reduces divider-induced error, and the 0.37 mV offset provides useful threshold precision. A shared pull-up or individual pull-ups determine the combined logic behavior. The implementation must account for input noise, reference accuracy, propagation delay, and the time required for the outputs to transition. For systems with fast transients, add filtering or a latch so that a short disturbance does not create an unintended fault indication.
推荐
LED and Backlight Drive Control
The LM393APWR can compare a dimming-control or sensing signal with a reference and provide a fault or enable signal for an LED or backlight driver. Its rail-to-rail input supports low-voltage control signals, and the open-collector output works with a pull-up when the downstream device accepts an active-low fault input. In a multi-channel backlight system, the two independent channels can monitor separate conditions while each output provides a wired-AND fault indication. The low 0.37 mV input offset improves comparison accuracy near the threshold, but LED-driver ripple must still be filtered to prevent false triggering. Select the pull-up resistor to balance low power consumption against acceptable output rise time, and confirm that the downstream LED driver recognizes the resulting logic levels.
推荐
推荐产品汇总
工程参考数据: LM393APWR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM393BPWR | LM2903APWR | LM2903BPWR | LM2903QPWR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin TSSOP (PW) | 8-pin TSSOP (PW) | 8-pin TSSOP (PW) | 8-pin TSSOP (PW) | 8-pin TSSOP (PW) |
| Grade | Precision A grade, industrial grade | B version | A grade | B version | Q automotive ordering designation |
关键差异点
- Precision A-grade threshold accuracy (对比 LM393BPWR)
- Low input bias for high-impedance sensing (对比 LM2903APWR)
- Direct industrial A-grade family positioning (对比 LM2903QPWR)
设计说明
Do not treat the open-collector output as a push-pull logic output. Each output requires an external pull-up resistor, and its high voltage is determined by that resistor and the connected logic supply. Omitting the pull-up leaves the node floating. When combining outputs, confirm that all devices can tolerate the resulting shared pull-up voltage and that the sink current remains within the comparator's specified output-current limits.
Keep the comparator input traces short and place any input resistors close to the relevant pins. The 3.5 nA input bias current can create a measurable voltage error when driven through a high source impedance. Avoid routing the inputs alongside motor-switch nodes and relay contacts, and use a local reference bypass capacitor where the reference source is not already adequately decoupled.
Choose the pull-up resistor using the required logic rise time, input capacitance, and available output sink current. A smaller pull-up produces faster rising edges but increases supply current during the low output state. A larger pull-up reduces power consumption but slows transitions and increases susceptibility to capacitive noise. Validate the resulting network with the actual logic input and board capacitance rather than relying only on a nominal logic rise-time target.
合规信息
The manufacturer identifies LM393APWR as an industrial-grade part. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed for the exact ordering suffix before release to a restricted bill of materials.