LMR931G-GTR - 5V Low-Power Rail-to-Rail Op Amp | ROHM
料号: LMR931G-GTR ✗ 停产LMR931G-GTR 概述
An operational amplifier, or op amp, is an analog integrated circuit that uses high-gain differential amplification to buffer, amplify, or condition signals. The LMR931G belongs to the broader hierarchy of operational amplifier, analog IC, and semiconductor products. Rail-to-rail input operation allows signals to approach the supply rails, while rail-to-rail output operation gives the output stage greater voltage range than a conventional output stage. These characteristics are particularly useful in battery-powered equipment and low-voltage sensor systems where signal headroom is limited.
ROHM describes the LMR931G family as a low-power, low-voltage, input/output full-swing operational amplifier. The verified product information identifies a single amplifier with one circuit, a 5 V nominal operating supply, and a 5-SSOP package. The family also includes single, dual, and quad configurations, allowing a system designer to standardize amplifier functions across channels without changing the basic low-power operating approach. Shutdown is specifically identified for the LMR981 and LMR982 family members rather than for the LMR931G.
The LMR931G-GTR is suited to low-voltage sensor interfaces, portable measurement systems, signal buffers, audio and communication support circuits, industrial controls, and general-purpose analog amplification. Its low-power operating concept can reduce system burden in applications where the amplifier does not need to operate continuously at high speed. Rail-to-rail input behavior can simplify biasing around midpoint, while full-swing output improves signal utilization at low supply voltages.
Designers should verify the electrical limits, common-mode range, output swing, stability requirements, and recommended external components in the ROHM datasheet before release. Decoupling capacitors should be placed close to the supply and ground pins, and feedback and compensation networks should preserve the intended closed-loop response. Input and output behavior must also be checked against source impedance, load impedance, and the operating voltage of the surrounding circuit.
This page combines the verified ROHM product information with package, application, comparison, and design guidance focused on practical selection. It identifies the LMR931G-GTR as a low-power, rail-to-rail single op amp and separates confirmed catalog facts from electrical parameters that require confirmation from the manufacturer datasheet.
直接替换替代料: LMR931G-GTR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料LMR931G-GTR 最大额定值与电气特性
| Product Type | Operational Amplifier |
| Number of Channels | 1 circuit |
| Amplifier Type | General-purpose operational amplifier |
| Nominal Supply Voltage | 5 V |
| Output Swing | Input/output full swing |
| Rail-to-Rail Input | Yes |
| Rail-to-Rail Output | Yes |
| Input Bias Current | 5 nA |
| Gain Bandwidth Product | 1.4 MHz |
| Slew Rate | 0.42 V/us |
| 封装 | 5-pin SSOP |
| Packaging | Tape and reel |
| 安装类型 | Surface mount |
| RoHS 状态 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
LMR931G-GTR 5-pin ssop 引脚配置指南
LMR931G-GTR(5-pin ssop 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LMR931G-GTR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LMR931G-GTR 适用于 6 应用s: Low-Voltage Sensor Conditioning, Portable Measurement Systems, Audio Signal Buffering, Industrial Control Interfaces, Communications Support Circuit, Data Acquisition Front End.
Low-Voltage Sensor Conditioning
The LMR931G-GTR fits sensor-amplifier stages that operate from a nominal 5 V rail and need to process signals near either supply limit. Its rail-to-rail input behavior provides useful common-mode headroom, while the reported 5 nA input bias current helps reduce bias-related error with high-impedance sources. The 1.4 MHz gain-bandwidth product supports ordinary low-frequency conditioning rather than high-bandwidth sensing. Place the amplifier in a conventional noninverting or inverting configuration, keep feedback loops short, and verify source impedance, sensor range, and the datasheet stability requirements before committing the gain and compensation values.
推荐
Portable Measurement Systems
Battery-powered instruments benefit from an operational amplifier that combines low-power operation with a nominal 5 V supply. The LMR931G-GTR can buffer sensor outputs, level-shift within the supply range, and drive moderate loads where the 1.4 MHz gain-bandwidth product and 0.42 V/us slew rate are adequate. Rail-to-rail output operation can maximize the available signal swing in compact systems. The design should account for shutdown behavior at the system level, avoid driving capacitive loads unless stability is confirmed, and use local supply bypassing to limit noise coupled into the measurement path.
推荐
Audio Signal Buffering
The LMR931G-GTR can serve as a low-voltage audio buffer when the source and destination operate within its nominal 5 V supply. Rail-to-rail input and output characteristics improve headroom in compact audio paths, while the 0.42 V/us slew rate is suitable for many low-bandwidth audio signals. Its 1.4 MHz gain-bandwidth product constrains high-order filtering and very high-frequency behavior. Confirm the output-load capability, output swing, noise, and stability in the manufacturer datasheet, and place the device so return currents from the audio path do not share sensitive input-ground routes.
推荐
Industrial Control Interfaces
LMR931G-GTR is suitable for general-purpose industrial interface stages that require a single low-power amplifier, nominal 5 V operation, and rail-to-rail signal handling. It can amplify or buffer low-bandwidth control signals and interface limited-range sensor outputs to a controller. The reported 5 nA input bias current is advantageous with high-impedance sources, but system-level EMI immunity and transient protection must be handled separately from the amplifier itself. Review the operating-temperature limits, supply tolerances, and input/output absolute maximum ratings before using the device in industrial equipment.
推荐
Communications Support Circuit
The LMR931G-GTR can be used in low-speed communications equipment for baseband buffering, thresholding, or gain stages when a nominal 5 V rail is available. Its 1.4 MHz bandwidth and 0.42 V/us slew rate are adequate for many low-rate support circuits but do not target high-speed line-driver applications. The single-channel 5-SSOP format also saves board area compared with a dual amplifier when only one channel is needed. Engineers should evaluate input capacitance, capacitive loading, output settling, and supply-noise behavior against the signal timing requirements of the communication standard.
推荐
Data Acquisition Front End
LMR931G-GTR can provide the first active stage of a compact data-acquisition chain when signals require buffering, modest gain, and operation from a low-voltage supply. Rail-to-rail input operation supports sensor outputs near the supply rails, and the 1.4 MHz gain-bandwidth product can accommodate many slowly varying measurements. The amplifier should be selected only after checking input bias current, offset, noise, settling behavior, and common-mode limits against the required accuracy. Use short, shielded signal routes, a quiet reference node, and local bypass capacitors, especially when the source impedance is high.
推荐
推荐产品汇总
工程参考数据: LMR931G-GTR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Brand | ROHM Semiconductor |
| Package | 5-pin SSOP |
| Number of Channels | 1 circuit |
| Nominal Supply Voltage | 5 V |
| Input Bias Current | 5 nA |
| Gain Bandwidth Product | 1.4 MHz |
| Slew Rate | 0.42 V/us |
| Rail-to-Rail Input | Yes |
| Rail-to-Rail Output | Yes |
| Operating Class | Low-power, low-voltage operational amplifier |
关键差异点
- Rail-to-rail signal handling in a low-power single-amplifier package (对比 LMV931MFX/NOPB)
- Single-channel format avoids unused amplifier channels (对比 LMR931G dual configuration)
- Low-voltage operation with useful input bias-current performance (对比 OPA343NA/250)
设计说明
Place the supply bypass capacitor and the amplifier ground connection close to the device pins. Route the feedback components directly from the output to the inverting input and keep the non-inverting input trace short, especially when the source impedance is high. Because the verified catalog information does not state the pin numbers, use the ROHM package drawing and pin-description table before assigning either power or signal nets.
Do not treat rail-to-rail operation as an unlimited range. The usable input and output span still depends on supply voltage, load, output swing, and common-mode limits in the manufacturer datasheet. The reported 1.4 MHz gain-bandwidth product also means that high closed-loop gain reduces available bandwidth. Validate the intended gain, signal bandwidth, and capacitive load before release rather than relying only on the nominal rail-to-rail description.
For high-impedance sources, minimize leakage and board contamination around the input node, and keep sensitive traces away from switching nodes and switching-regulator outputs. The 5 nA input bias-current figure makes source impedance important because bias-current error depends on the impedance seen by the input. Confirm whether the design also requires the amplifier's full noise and offset specifications, which should be read from the ROHM datasheet.
Power the LMR931G-GTR from a nominal 5 V rail only after checking its operating-supply range, quiescent current, and load behavior. Low-power operation does not remove the need for local decoupling because supply ripple and ground movement can still affect precision analog measurements. Where multiple analog and digital loads share a board, route amplifier return current directly to the quiet ground reference rather than through digital return paths.
合规信息
The available product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 status is not stated; not_applicable here means automotive qualification was not established from the available information, not that the device is qualified or disqualified.